LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Infiniti >> 2007 >> QX56 AWD >> Repair and Diagnosis >> Accessories & Equipment >> Communication Devices >> Body Control System >> BCM (Body Control Module) >> Configuration >> Write Configuration Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Write Configuration Procedure

CAUTION: If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be detected in self-diagnosis depending on control unit which carries out CAN communication.
  1. With ignition switch OFF, connect CONSULT-II and CONSULT-II CONVERTER to data link connector and turn ignition switch ON.
    Fig 1: Connecting CONSULT-II And CONSULT-II CONVERTER To Data Link Connector
    G04899601
  2. Touch "START (NISSAN BASED VHCL)".
    Fig 2: CONSULT-II Screen Display - START (NISSAN BASED VHCL)
    G04899602
  3. Touch "BCM" on "SELECT SYSTEM" screen.

    If "BCM" is not indicated, go to "CONSULT-II DATA LINK CONNECTOR (DLC) CIRCUIT ".

    Fig 3: CONSULT-II Function Screen Display - Select System
    G04899603
  4. Touch "BCM" on "SELECT TEST ITEM" screen.
    Fig 4: CONSULT-II Screen Display - SELECT TEST ITEM
    G04903945
  5. Touch "CONFIGURATION" on "SELECT DIAG MODE" screen.
    Fig 5: CONSULT-II Screen Display - SELECT DIAG MODE
    G04899604
  6. Touch "JA60" and "OK" on "VEHICLE SELECT" screen. For canceling, touch "CANCEL" on "VEHICLE SELECT" screen.
    NOTE: Confirm vehicle model. Refer to "MODEL VARIATION " in GI section.
    Fig 6: CONSULT-II Screen Display - SELECT DIAG MODE
    G04903947
  7. Touch "WRITE CONFIGURATION" on "SELECT CONFIG ITEM" screen.
    Fig 7: CONSULT-II Screen Display - SELECT CONFIG ITEM
    G04903948
  8. Touch "YES".

    For canceling, touch "NO".

    Fig 8: CONSULT-II Screen Display - CONFIGURATION
    G04903958
  9. Touch "WITH" or "WITHOUT" on "WRITE CONFIGURATION" screen based on the following ITEM LIST.
    • Depending on CONSULT-II software version being used, some or all of the write configuration items shown in the following configuration lists may be displayed. If an item does not appear on the CONSULT-II "WRITE CONFIGURATION" screen(s), then it is an auto setting item and it cannot be manually set or changed.
      ITEM REFERENCE

      ITEM SET VAL
      DTRL WITH <=> WITHOUT
      SPEED SNS WIP WITH <=> WITHOUT
      NOTE: Confirm vehicle model. Refer to "MODEL VARIATION " in GI section.
  10. Touch "CHNG SETTING" on "WRITE CONFIGURATION" screen.
    CAUTION: Make sure to touch "CHNG SETTING" even if the indicated configuration of new BCM is same as the desirable configuration.
    If not, configuration which is set automatically by selecting vehicle model cannot be memorized.
  11. Touch "OK" on "WRITE CONFIGURATION" screen.

    If "CANCEL" is touched, it will return to previous screen.

    Fig 9: CONSULT-II Screen Display - WRITE CONFIGURATION
    G04903959
  12. Wait until the next screen during setting.
    Fig 10: CONSULT-II Screen Display - WRITE CONFIGURATION
    G04903960
  13. WRITE CONFIGURATION results are printed out automatically. Confirm "WRITE CONFIGURATION" is correctly executed by comparing sheet automatically printed out with applicable configuration list shown in step  9.
    Fig 11: CONSULT-II Screen Display - WRITE CONFIGURATION
    G04903961
  14. Touch "OK" on "WRITE CONFIGURATION" screen. WRITE CONFIGURATION is completed.
    Fig 12: CONSULT-II Screen Display - WRITE CONFIGURATION
    G04903962
scientia non olet · About LEMON Manuals