Encoder Circuit Check Rear LH or RH

1. Turn ignition switch OFF.
2. Disconnect rear power window motor LH or RH.
3. Turn ignition switch ON.
4. Check voltage between rear power window motor LH or RH connector D204 (LH) or D304 (RH) terminal 4 and ground.

   4 - Ground : Approx. 10V 

OK or NG 

OK: GO TO  3.

NG: GO TO 2.

Fig 1: Checking Voltage Between Rear Power Window Motor LH Or RH Connector Terminal And Ground

1. Turn ignition switch OFF.
2. Disconnect rear power window motor LH or RH and rear power window control unit LH or RH.
3. Check continuity between rear power window motor LH or RH connector D204 (LH) or D304 (RH) (B) terminal 4 and rear power window control unit LH or RH connector D209 (LH) or D309 (RH) (A) terminal 5.

   4 - 5 : Continuity should exist. 

OK or NG 

OK: Replace rear power window switch LH or RH. Refer to "REMOVAL AND INSTALLATION ".

NG: Repair or replace harness.

Fig 2: Checking Continuity Between Rear Power Window Motor And Control Unit LH Or RH Connector Terminals

1. Disconnect rear power window motor LH or RH.
2. Check continuity between rear power window motor LH or RH connector D204 (LH) or D304 (RH) terminal 6 and ground.

   6 - Ground : Continuity should exist. 

OK or NG 

OK: GO TO  5.

NG: GO TO 4.

Fig 3: Checking Continuity Between Rear Power Window Motor LH Or RH Connector Terminal And Ground

1. Disconnect rear power window control unit LH or RH.
2. Check continuity between rear power window motor LH or RH connector D204 (LH) or D304 (RH) terminal 6 and rear power window control unit LH or RH connector D209 (LH), D309 (RH) terminal 3.

   6 - 3 : Continuity should exist. 

OK or NG 

OK: Replace rear power window control unit LH or RH.

NG: Repair or replace harness.

Fig 4: Checking Continuity Between Rear Power Window Motor And Control Unit LH Or RH Connector Terminals

1. Connect rear power window motor LH or RH and rear power window control unit LH or RH.
2. Turn ignition switch ON.
3. Check the signal between rear power window control unit LH or RH connector D209 (LH) or D309 (RH) terminal 4 and ground with oscilloscope.
   CONNECTOR TERMINALS REFERENCE CHART
   
   

   Connector	Terminals		Condition	Signal
   	(+)	(-)
   D209 (LH)	4	Ground	Opening
   D309 (RH)	4

   Fig 5: Checking Signal Between Rear Power Window Control Unit LH Or RH Connector Terminals And Ground With Oscilloscope

   

OK or NG 

OK: GO TO 6.

NG: Replace rear power window control unit LH or RH.

1. Turn ignition switch OFF.
2. Disconnect rear power window control unit LH or RH and rear power window motor LH or RH.
3. Check continuity between rear power window control unit LH or RH connector D209 (LH) or D309 (RH) terminal 4 and rear power window motor LH or RH connector D204 (LH), D304 (RH) terminal 3.

   4 - 3 : Continuity should exist. 

   Fig 6: Checking Continuity Between Rear Power Window Control Unit And Motor LH Or RH Connector Terminals

   

OK or NG 

OK: Replace rear power window motor LH or RH. Refer to "REMOVAL AND INSTALLATION ".

NG: Repair or replace harness.