LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Infiniti >> 2013 >> M56 Base >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System - DTCS P0190 To P1084 >> DTC P100A, P100B: VVEL System >> Diagnosis Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnosis Procedure

  1. VVEL ACTUATOR MOTOR OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT 
    1. Disconnect VVEL control module harness connector.
    2. Disconnect VVEL actuator motor harness connector.
    3. Check the continuity between VVEL control module harness connector and VVEL actuator motor harness connector.
      DTC No. VVEL control module VVEL actuator motor Continuity
      Bank Connector Terminal Connector Terminal
      P100A 1 E15 12 F73 1 Existed
      2 Not existed
      25 1 Not existed
      2 Existed
      P100B 2 2 F71 1 Existed
      2 Not existed
      15 1 Not existed
      2 Existed
    4. Also check harness for short to ground and power.

      Is the inspection result normal? 

      YES: GO TO  3.

      NO: GO TO 2.

  2. DETECT MALFUNCTIONING PART 

    Check the following.

    • Harness for open or short between VVEL actuator motor and VVEL control module
    • Loose or poor connection for each connector and harness

      : Repair open circuit, short to ground or short to power in harness or connectors.

  3. CHECK VVEL ACTUATOR MOTOR 

    Refer to "COMPONENT INSPECTION (VVEL ACTUATOR MOTOR) ".

    Is the inspection result normal? 

    YES: GO TO  5.

    NO: GO TO 4.

  4. REPLACE VVEL ACTUATOR SUB ASSEMBLY 

    Replace VVEL actuator sub assembly. Refer to "EXPLODED VIEW ".

    : INSPECTION END

  5. CHECK INTERMITTENT INCIDENT 

    Refer to "INTERMITTENT INCIDENT ".

    Is the inspection result normal? 

    YES: GO TO 6.

    NO: Repair or replace.

  6. REPLACE VVEL CONTROL MODULE 

    Replace VVEL control module. Refer to "REMOVAL AND INSTALLATION ".

    : GO TO 7.

  7. PERFORM DTC CONFIRMATION PROCEDURE 
    1. Turn ignition switch ON.
    2. Erase 1st trip DTC.
    3. Perform DTC Confirmation Procedure.

      See "DTC LOGIC ".

      Is the DTC P100A or P100B displayed again? 

      YES: GO TO 8.

      NO: INSPECTION END

  8. CHECK VVEL ACTUATOR SUB ASSEMBLY 

    Refer to "COMPONENT INSPECTION (VVEL ACTUATOR SUB ASSEMBLY) ".

    Is the inspection result normal? 

    YES: GO TO  10.

    NO: GO TO 9.

  9. REPLACE VVEL ACTUATOR SUB ASSEMBLY 

    Replace VVEL actuator sub assembly. Refer to "EXPLODED VIEW ".

    : INSPECTION END

  10. CHECK VVEL LADDER ASSEMBLY 

    Refer to "EXPLODED VIEW ".

    Is the inspection result normal? 

    YES: GO TO  12.

    NO: GO TO 11.

  11. REPLACE CYLINDER HEAD, VVEL LADDER ASSEMBLY AND VVEL ACTUATOR SUB ASSEMBLY 

    Replace cylinder head, VVEL ladder assembly and VVEL actuator sub assembly.

    Refer to "EXPLODED VIEW " (Cylinder head).

    Refer to "EXPLODED VIEW " (VVEL ladder assembly and VVEL actuator sub assembly)

    : INSPECTION END

  12. CHECK INTERMITTENT INCIDENT 

    Refer to "INTERMITTENT INCIDENT ".

    : INSPECTION END

scientia non olet · About LEMON Manuals