Self Diagnostic Result
Refer to DTC Index .
When "CRNT" is displayed on self-diagnosis result
- The system is presently malfunctioning.
When "PAST" is displayed on self-diagnosis result
- System malfunction in the past is detected, but the system is presently normal.
Freeze frame data (FFD)
When DTC is detected, a vehicle state shown below is recorded and displayed on CONSULT.
|
Item name |
Indication/Unit |
Display item |
|
ODO/TRIP METER |
km |
Total mileage (Odometer value) of the moment a particular. |
|
DTC LOCAL CODE |
-- |
DTC code is displayed but not used. |
|
IGN VOLT |
V |
Displays the ignition power supply voltage. |
|
VEHICLE SPEED |
km |
Displays the vehicle speed. |
|
FR WHEEL SPEED |
rpm |
Displays the rotational speed of front RH tire. |
|
FL WHEEL SPEED |
rpm |
Displays the rotational speed of front LH tire. |
|
RR WHEEL SPEED |
rpm |
Displays the rotational speed of rear RH tire. |
|
RL WHEEL SPEED |
rpm |
Displays the rotational speed of rear LH tire. |
|
STEERING ANG SENSOR |
deg |
Displays the steering angle from the steering angle sensor. |
|
DECEL G SENSOR |
G |
Displays the decel G. |
|
SIDE G SENSOR |
G |
Displays the side G. |
|
YAW RATE SENSOR |
deg/s |
Displays the yaw rate. |
|
ACCELE PEDAL POSITION |
% |
Displays the accelerator pedal position. |
|
SHIFT POSITION |
Off / P / R / N / D (A) / S / L / B / 1- 6 / M 1 -M 8 / A 1 - A 6 |
Displays the shift position. |
|
BRAKE SWITCH 2 |
Off / On |
Displays brake pedal operating status. |
|
BRAKE SWITCH 1 |
Off / On |
Displays brake pedal operating status. |
|
STOP LAMP SW |
ACT / INACT |
Displays the stop lamp switch status. |
|
PRESS SENSOR |
bar |
Displays the brake fluid pressure. |
|
ABS |
NORMAL / ABNOR |
Displays ABS function status. |
|
ABS MALF |
Off / On |
Displays ABS function malfunction status. |
|
TCS |
NORMAL / ABNOR |
Displays TCS function status. |
|
TCS MALF |
Off / On |
Displays TCS function malfunction status. |
|
VDC |
NORMAL / ABNOR |
Displays VDC function status. |
|
VDC MALF |
Off / On |
Displays VDC function malfunction status. |
|
VDC OFF SW |
Off / On |
Displays VDC OFF switch status. |
|
ACCELE PEDAL MALF |
Off / On |
Displays accelerator pedal malfunction status. |
|
DRIVE MODE SELECTOR |
STD / SPORT / SPORT+ / ECO / SNOW / PERSO |
Displays the drive mode select switch selection status. |
|
LANE MARKER (LH)*1 |
NOT / DETECT |
Displays the lane marker (LH) detection status. |
|
LANE MARKER (RH)*1 |
NOT / DETECT |
Displays the lane marker (RH) detection status. |
|
TURN SIGNAL (LH)*1 |
Off / On |
Displays the turn signal switch (LH) operating status. |
|
TURN SIGNAL (RH)*1 |
Off / On |
Displays the turn signal switch (RH) operating status. |
|
TURN SIGNAL SWITCH*1 |
Off / LEFT / RIGHT / MALF |
Displays the turn signal switch operating status. |
|
DAST*1 |
Off / On |
Displays the operation request status to direct adaptive steering. |
|
ROAD DISTORTION*1 |
1/m |
Displays the road distortion rate radius. |
|
COMMAND ST ANG*1 |
rad |
Displays the steering command value to direct adaptive steering. |
|
ST WHL FORCE TORQUE*1 |
Nm |
Displays the estimated value for the steering wheel force torque. |
|
COMMAND ST WHL FORCE*1 |
N |
Displays the steering reaction force command value to direct adaptive steering. |
|
ADAS COND*1 |
NORMAL / ABNOR |
Displays the ADAS control unit function status. |
|
DDS operating condition*2 |
Off / On |
Displays the dynamic digital suspension condition. |
|
Engine rpm*2 |
rpm |
Displays the engine speed. |
|
DMC) CAN signal not receive*2 |
Non detection / Detection |
Displays the CAN signal not receive of digital motion control. |
|
DMC) CAN signal irregularity 1*2 |
Non detection / Detection |
Displays the CAN signal irregularity (message counter) of digital motion control. |
|
DMC) CAN signal irregularity 2*2 |
Non detection / Detection |
Displays the CAN signal irregularity (checksum) of digital motion control. |
|
DMC) CAN signal invalid*2 |
Non detection / Detection |
Displays the CAN signal invalid of digital motion control. |
|
Stop/Start*2 |
A |
Displays the Stop/Start status. |
|
FR shock ab command current*2 |
A |
Displays the dynamic digital suspension (FR) command current. |
|
FL shock ab command current*2 |
A |
Displays the dynamic digital suspension (FL) command current. |
|
RR shock ab command current*2 |
A |
Displays the dynamic digital suspension (RR) command current. |
|
RL shock ab command current*2 |
A |
Displays the dynamic digital suspension (RL) command current. |
|
DMC status*2 |
Inactive / Active 1 /Active 2 / Active 3 /Active 4 /Not connect current line / Active test 1 /Active test 2 / Other control unit / CAN communication / Control unit |
Displays the digital motion control status. |
|
WIPER STATUS*1 |
Off / LOW / HIGH / MALF |
Displays the wiper operating status. |
|
CAN DIAG PERMIS CONDITION |
Off / On |
Displays CAN network diagnosis status. |
|
THRTL OPENING |
% |
Displays the electric throttle position. |
*1: Models with active lane control
*2: Models with digital motion control