LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Infiniti >> 2016 >> QX50 AWD >> Repair and Diagnosis (Single Page) >> Engine Performance >> System >> Engine Control System Diagnostic Trouble Codes (DTCS) (P0447-P2138) >> DTC/Circuit Diagnosis >> DTC P2122, P2123: Accelerator Pedal Position (App) Sensor 1 Circuit Low/High Input >> Diagnosis Procedure >> Diagnostic Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnostic Test

  1. CHECK GROUND CONNECTION

    1. Turn ignition switch OFF.
    2. Check ground connection M95. Refer to Ground Inspection in CIRCUIT INSPECTION .

    Is the inspection result normal?

    YES 

    GO TO STEP 2  .

    NO 

    Repair or replace ground connection.

  2. CHECK APP SENSOR 1 POWER SUPPLY CIRCUIT

    1. Disconnect accelerator pedal position (APP) sensor harness connector.
    2. Turn ignition switch ON.
    3. Check the voltage between APP sensor harness connector and ground.
      APP sensor Ground Voltage (V)
      Connector Terminal
      E112
      (Without ICC)
      E116
      (With ICC)      		 5 Ground Approx. 5

    Is the inspection result normal?

    YES 

    GO TO STEP 4  .

    NO 

    GO TO STEP 3  .

  3. DETECT MALFUNCTIONING PART

    Check the following:

    • Harness connectors M6, E106
    • Harness for open or short between ECM and accelerator pedal position sensor

    Repair open circuit, short to ground or short to power in harness or connectors.

  4. CHECK APP SENSOR 1 GROUND CIRCUIT FOR OPEN AND SHORT

    1. Turn ignition switch OFF.
    2. Disconnect ECM harness connector.
    3. Check the continuity between APP sensor harness connector and ECM harness connector.
      APP sensor ECM Continuity
      Connector Terminal Connector Terminal
      E112
      (Without ICC)      		 4 M107 100 Existed
      E116
      (With ICC)      		 1
    4. Also check harness for short to ground and short to power.

    Is the inspection result normal?

    YES 

    GO TO STEP 6  .

    NO 

    GO TO STEP 5  .

  5. DETECT MALFUNCTIONING PART

    Check the following:

    • Harness connectors M6, E106
    • Harness for open or short between ECM and accelerator pedal position sensor

    Repair open circuit, short to ground or short to power in harness or connectors.

  6. CHECK APP SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

    1. Check the continuity between APP sensor harness connector and ECM harness connector.
      APP sensor ECM Continuity
      Connector Terminal Connector Terminal
      E112
      (Without ICC)      		 3 M107 97 Existed
      E116
      (With ICC)      		 4
    2. Also check harness for short to ground and short to power.

    Is the inspection result normal?

    YES 

    GO TO STEP 8  .

    NO 

    GO TO STEP 7  .

  7. DETECT MALFUNCTIONING PART

    Check the following:

    • Harness connectors M6, E106
    • Harness for open or short between ECM and accelerator pedal position sensor

    Repair open circuit, short to ground or short to power in harness or connectors.

  8. CHECK APP SENSOR

    Refer to COMPONENT INSPECTION .

    Is the inspection result normal?

    YES 

    GO TO STEP 10  .

    NO 

    GO TO STEP 9  .

  9. REPLACE ACCELERATOR PEDAL ASSEMBLY

    1. Replace accelerator pedal assembly. Refer to REMOVAL AND INSTALLATION .
    2. Go to SPECIAL REPAIR REQUIREMENT .

    INSPECTION END

  10. CHECK INTERMITTENT INCIDENT

    Refer to INTERMITTENT INCIDENT .

    INSPECTION END

scientia non olet · About LEMON Manuals