LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Infiniti >> 2017 >> Q50 Base, AWD >> Repair and Diagnosis (Single Page) >> Steering >> Steering Control Systems >> Steering Control System (Direct Adaptive Steering) (Basic Inspection) (Except Hybrid) >> Basic Inspection >> Additional Service When Replacing Control Module >> Work Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Work Procedure

WARNING:

Never move the vehicle during "DAST CALIBRATION (MODE1)" because the steering gear is held in neutral position until ignition switch is turned OFF.

CAUTION:
  • Be careful for the moving parts, steering wheel and front wheels are steered automatically when start "DAST CALIBRATION (MODE1)".
  • Do not rotate road wheels during the DAST calibration because the system is detected the vehicle running.

  1. CHECK OFF-CENTER (1)

    G-20With CONSULT 

    1. Set the vehicle to the straight-ahead position.
    2. Turn the ignition switch ON.
      CAUTION:

      Never start the engine.

    3. On the CONSULT screen, select "EPS/DAST 3">>"DATA MONITOR">>"ST ANGLE SENSOR", and then and then check the value.
      Monitor item Standard value
      ST ANGLE SENSOR ST ANGLE SENSOR ≤+-120 deg

    Is the inspection result normal?

    YES 

    GO TO STEP 2  .

    NO 

    • Refer to DIAGNOSIS PROCEDURE to correct off-center and then, GO TO STEP 2  .
      CAUTION:

      Proceeding to the next step with off-center bigger than 120 deg causes the spiral cable to be torn off.

  2. PREPARATION

    1. Set the front wheel on the turn table.
      NOTE:

      Do not lift up the vehicle during "DAST CALIBRATION (MODE1)"

    2. Connect the battery charger to protect the battery.
      NOTE:

      Much electricity is used in "DAST CALIBRATION (MODE1)".

    3. Connect the CONSULT.
    4. Turn the ignition switch ON.
      CAUTION:

      Never start the engine.

    GO TO STEP 3  .

  3. ECU CONFIGURATION

    G-20With CONSULT 

    1. Perform configuration for steering force control module. Refer to WORK PROCEDURE .
    2. Perform configuration for steering angle main control module. Refer to WORK PROCEDURE .
    3. Perform configuration for steering angle sub control module. Refer to WORK PROCEDURE .

    GO TO STEP 4  .

  4. DAST CALIBRATION (MODE1) [CLUTCH PHASE LEARNING]

    G-20With CONSULT 

    1. Perform "DAST CALIBRATION (MODE1)". Refer to DESCRIPTION .
    2. Turn the ignition switch OFF.
      CAUTION:

      Be sure to perform this step.

    GO TO STEP 5  .

  5. CHECK OFF-CENTER (2)

    G-20With CONSULT 

    NOTE:

    This confirmation is procedure to confirm that the steering wheel is not rotated 360 deg when performing the DAST calibration.

    CAUTION:

    Proceeding to the next step with the steering wheel rotated 360 deg causes the spiral cable to be torn off.

    1. Turn the ignition switch ON.
      CAUTION:

      Never start the engine.

    2. On the CONSULT screen, select "EPS/DAST 3">>"DATA MONITOR">>"ST ANGLE SENSOR", and then and then check the value.
      Monitor item Standard value
      ST ANGLE SENSOR ST ANGLE SENSOR ≤+-20 deg

    Is the inspection result normal?

    YES 

    GO TO STEP 7  .

    NO 

    GO TO STEP 6  .

  6. CORRECT STEERING WHEEL NEUTRAL POSITION

    G-20With CONSULT 

    1. Separate steering upper shaft from steering clutch assembly. And then, turn the steering wheel to the direction that the value returns to 0 deg with checking "ST ANGLE SENSOR" on "DATA MONITOR".
    2. Connect steering clutch assembly and steering upper shaft. Refer to REMOVAL AND INSTALLATION .

    Re-perform the work from configuration to reset the learning information of clutch phaze learning. GO TO STEP   3  .

  7. DAST CALIBRATION (MODE1) [STEERING RACK NEUTRAL POSITION LEARNING]

    G-20With CONSULT 

    Perform "DAST CALIBRATION (MODE1)". Refer to DESCRIPTION .

    GO TO STEP 8  .

  8. ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION

    G-20With CONSULT 

    1. On the CONSULT screen, select "ABS">>"WORK SUPPORT">>"ST ANGLE SENSOR ADJUSTMENT".
    2. Touch START.
      CAUTION:

      Never touch steering wheel while adjusting steering angle sensor.

    3. After approx. 10 seconds, select "END".
    4. Turn ignition switch OFF, and then turn it ON again.
      CAUTION:

      Be sure to perform this step.

    GO TO STEP 9  .

  9. PERFORM SELF-DIAGNOSIS

    G-20With CONSULT 

    1. Turn ignition switch OFF and wait at least 10 seconds.
    2. Start the engine.
      CAUTION:

      Never drive the vehicle.

    3. Perform self-diagnosis for "EPS/DAST 3", "DAST 1" and "DAST 2".

    Is any DTC detected?

    YES 

    When other than above DTC is detected, Perform trouble diagnosis for the detected DTC. Refer to DTC INDEX (EPS/DAST 3), DTC INDEX (DAST 1), DTC INDEX (DAST 2).

    NO 

    GO TO STEP 10  .

  10. FINAL CONFIRMATION

    G-20With CONSULT 

    1. Turn the ignition switch OFF to ON.
      CAUTION:

      Never start the engine.

    2. On the CONSULT screen, select "EPS/DAST 3">>"DATA MONITOR">>"ANGLE 1', and then and then check the value.
      Monitor item Standard value
      ANGLE 1 - 4.4 ≤ ANGLE 1 ≤ 4.4

    Is the confirmation result normal?

    YES 

    WORK END

    NO 

    Slightly lower the tilt position, and then re-perform DAST CALIBRATION (MODE1)  .

scientia non olet · About LEMON Manuals