LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Infiniti >> 2017 >> Q60 Base, AWD >> Repair and Diagnosis >> Steering >> Steering Control Systems >> Steering Control System (Direct Adaptive Steering) (DTC/Circuit Diagnosis) >> DTC / Circuit Diagnosis >> Power Supply And Ground Circuit >> Diagnosis Procedure >> Diagnostic Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnostic Test

  1. CHECK STEERING FORCE CONTROL MODULE GROUND CIRCUIT

    1. Turn the ignition switch OFF.
    2. Disconnect steering force control module harness connector.
    3. Check the continuity between control module harness connector and ground.
      Steering force control module - Continuity
      Connector Terminal
      M72 33 Ground Existed

    Is the inspection result normal?

    YES 

    GO TO STEP 2  .

    NO 

    Repair open circuit in harness or connectors.

  2. CHECK STEERING ANGLE MAIN CONTROL MODULE GROUND CIRCUIT

    1. Disconnect steering angle main control module harness connector.
    2. Check the continuity between control module harness connector and ground.
      Steering angle main control module - Continuity
      Connector Terminal
      E27 33 Ground Existed
      E28 39

    Is the inspection result normal?

    YES 

    GO TO STEP 3  .

    NO 

    Repair open circuit in harness or connectors.

  3. CHECK STEERING ANGLE SUB CONTROL MODULE GROUND CIRCUIT

    1. Disconnect steering angle sub control module harness connector.
    2. Check the continuity between control module harness connector and ground.
      Steering angle sub control module - Continuity
      Connector Terminal
      E30 33 Ground Existed
      E31 39

    Is the inspection result normal?

    YES 

    GO TO STEP 4  .

    NO 

    Repair open circuit in harness or connectors.

  4. CHECK STEERING FORCE CONTROL MODULE POWER SUPPLY CIRCUIT (1)

    1. Disconnect steering force control module harness connector.
    2. Check the voltage between steering force control module harness connector and ground.
      Steering force control module - Continuity
      Connector Terminal
      M72 34 Ground 10.5 - 16.0 V

    Is the inspection result normal?

    YES 

    GO TO STEP 6  .

    NO 

    GO TO STEP 5  .

  5. CHECK STEERING FORCE CONTROL MODULE POWER SUPPLY CIRCUIT (2)

    1. Check the 60A fusible link (#G).
    2. Check the harness for open or short between steering force control module harness connector No. 34 terminal and the 60A fusible link (#G).

    Is the inspection result normal?

    YES 

    Perform the trouble diagnosis for battery power supply circuit. Refer to WIRING DIAGRAM - BATTERY POWER SUPPLY - .

    NO 

    Repair or replace error - detected parts.

  6. CHECK STEERING ANGLE MAIN CONTROL MODULE POWER SUPPLY CIRCUIT (1)

    1. Turn the ignition switch OFF.
    2. Disconnect steering angle main control module harness connector.
    3. Check the voltage between steering angle main control module harness connector and ground.
      Steering angle main control module - Continuity
      Connector Terminal
      E27 34 Ground 10.5 - 16.0 V

    Is the inspection result normal?

    YES 

    GO TO STEP 8  .

    NO 

    GO TO STEP 7  .

  7. CHECK STEERING ANGLE MAIN CONTROL MODULE POWER SUPPLY CIRCUIT (2)

    1. Check the 100A fusible link (#J).
    2. Check the harness for open or short between steering angle main control module harness connector No. 34 terminal and the 100A fusible link (#J).

    Is the inspection result normal?

    YES 

    Perform the trouble diagnosis for battery power supply circuit. Refer to WIRING DIAGRAM - BATTERY POWER SUPPLY - .

    NO 

    Repair or replace error - detected parts.

  8. CHECK STEERING ANGLE SUB CONTROL MODULE POWER SUPPLY CIRCUIT (1)

    1. Turn the ignition switch OFF.
    2. Disconnect steering angle sub control module harness connector.
    3. Check the voltage between steering angle sub control module harness connector and ground.
      Steering angle sub control module - Continuity
      Connector Terminal
      E30 34 Ground 10.5 - 16.0 V

    Is the inspection result normal?

    YES 

    GO TO STEP 10  .

    NO 

    GO TO STEP 9  .

  9. CHECK STEERING ANGLE SUB CONTROL MODULE POWER SUPPLY CIRCUIT (2)

    1. Check the 100A fusible link (#H).
    2. Check the harness for open or short between steering angle sub control module harness connector No. 34 terminal and the 100A fusible link (#H).

    Is the inspection result normal?

    YES 

    Perform the trouble diagnosis for battery power supply circuit. Refer to WIRING DIAGRAM - BATTERY POWER SUPPLY - .

    NO 

    Repair or replace error - detected parts.

  10. CHECK IGNITION POWER SUPPLY FOR STEERING ANGLE MAIN CONTROL MODULE

    1. Turn the ignition switch OFF.
    2. Disconnect steering angle main control module harness connector.
    3. Check the voltage between steering angle main control module harness connector and ground.
      Steering angle main control module - Continuity
      Connector Terminal
      E26 25 Ground 0 V
    4. Turn the ignition switch ON.
    5. Check the voltage between steering angle control module harness connector and ground.
      Steering angle main control module - Continuity
      Connector Terminal
      E26 25 Ground 10.5 - 16.0 V

    Is the inspection result normal?

    YES 

    INSPECTION END.

    NO 

    GO TO STEP 11  .

  11. CHECK IGNITION POWER SUPPLY CIRCUIT (1)

    1. Turn the ignition switch OFF.
    2. Disconnect steering angle sub control module harness connector.
    3. Check the continuity between steering angle main control module harness connector and steering angle sub control module harness connector.
      Steering angle main control module Steering angle sub control module Continuity
      Connector Terminal Connector Terminal
      E26 25 E29 27 Existed

    Is the inspection result normal?

    YES 

    GO TO STEP 12  .

    NO 

    Repair or replace error - detected parts.

  12. CHECK INTERNAL CIRCUIT IN STEERING ANGLE SUB CONTROL MODULE

    Check the continuity between steering angle sub control module connector terminals.

    Steering angle sub control module Continuity
    Terminal
    25 27 Existed

    Is the inspection result normal?

    YES 

    GO TO STEP 13  .

    NO 

    Replace steering angle sub control module. Refer to REMOVAL AND INSTALLATION .

  13. CHECK IGNITION POWER SUPPLY FOR STEERING ANGLE SUB CONTROL MODULE

    1. Check the voltage between steering angle sub control module harness connector and ground.
      Steering angle sub control module - Continuity
      Connector Terminal
      E29 25 Ground 0 V
    2. Turn the ignition switch ON.
    3. Check the voltage between steering angle control module harness connector and ground.
      Steering angle sub control module - Continuity
      Connector Terminal
      E29 25 Ground 10.5 - 16.0 V

    Is the inspection result normal?

    YES 

    NO 

    GO TO STEP 14  .

  14. CHECK IGNITION POWER SUPPLY CIRCUIT (2)

    1. Turn the ignition switch OFF.
    2. Disconnect steering force control module harness connector.
    3. Check the continuity between steering angle sub control module harness connector and steering force control module harness connector.
      Steering angle sub control module Steering force control module Continuity
      Connector Terminal Connector Terminal
      E29 25 M71 27 Existed

    Is the inspection result normal?

    YES 

    GO TO STEP 15  .

    NO 

    Repair or replace error - detected parts.

  15. CHECK INTERNAL CIRCUIT IN STEERING FORCE CONTROL MODULE

    Check the continuity between steering force control module connector terminals.

    Steering force control module Continuity
    Terminal
    25 27 Existed

    Is the inspection result normal?

    YES 

    GO TO STEP 16  .

    NO 

    Replace steering force control module. Refer to REMOVAL AND INSTALLATION .

  16. CHECK IGNITION POWER SUPPLY FOR STEERING FORCE CONTROL MODULE

    1. Check the voltage between steering force control module harness connector and ground.
      Steering force control module - Continuity
      Connector Terminal
      M71 25 Ground 0 V
    2. Turn the ignition switch ON.
    3. Check the voltage between force control module harness connector and ground.
      Steering force control module - Continuity
      Connector Terminal
      M71 25 Ground 10.5 - 16.0 V

    Is the inspection result normal?

    YES 

    NO 

    GO TO STEP 17  .

  17. CHECK IGNITION POWER SUPPLY CIRCUIT (3)

    1. Turn the ignition switch OFF.
    2. Check the 10A fuse (#12).
    3. Disconnect fuse block (J/B) harness connector.
    4. Check the continuity between steering force control module connector and fuse block (J/B).
      Steering force control module Fuse block (J/B) Continuity
      Connector Terminal Connector Terminal
      M71 25 M133 20C Existed
    5. Check the continuity between steering force control module connector and ground.
      Steering force control module - Continuity
      Connector Terminal
      M71 25 Ground Not existed

    Is the inspection result normal?

    YES 

    Perform the trouble diagnosis for ignition power supply circuit. Refer to WIRING DIAGRAM - IGNITION POWER SUPPLY - .

    NO 

    Repair or replace error - detected parts.

scientia non olet · About LEMON Manuals