Active Test
The active test is used to determine and identify details of a malfunction, based on self-diagnosis test results and data obtained in the DATA MONITOR. In response to instructions from CONSULT, instead of those from chassis control module on the vehicle, a drive signal is sent to the actuator to check its operation.
CAUTION:
- Never perform ACTIVE TEST while driving the vehicle.
- Always bleed air from brake system before active test.
- Never perform active test when system is malfunctioning.
NOTE:
During an active test, sometimes a chassis control warning is displayed and the master warning lamp illuminates on the information display in the combination meter; however, this is not a malfunction.
| Test item | Operation | Description |
|---|---|---|
| BRAKE ACTUATOR 1 MODE 1 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 1 MODE 2 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 1 MODE 3 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 2 MODE 1 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 2 MODE 2 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 2 MODE 3 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 3 MODE 1 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 3 MODE 2 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 3 MODE 3 | Start | Controls brake fluid pressure. |
| ESS REALY ACTIVE | - | Displayed but not used. |
| ESS ACTIVE | - | Displayed but not used. |
| COMMAND STEERING ANGLE | Start | Transmits the steering command value 0 deg → 0.00349 deg (hold it for approximately 2 seconds) → 0 deg (hold it for approximately 2 seconds) → 0.00349 deg (hold it for approximately 2 seconds) → 0 deg to the steering force control module. |
| COMMAND ST WHL FORC | Start | Transmits the steering reaction force command value 0 N → 0.6 N (hold it for approximately 2 seconds) → 0 N (hold it for approximately 2 seconds) → 0.6 N (hold it for approximately 2 seconds) → 0 N to the steering force control module. |
| STOP LAMP OFF RELAY 1 ACTIVE | - | Displayed but not used. |
| STOP LAMP OFF RELAY 2 ACTIVE | - | Displayed but not used. |
| MASTER WARNING ACTIVE | On | If touching "On" with the master warning lamp not illuminated, the master warning lamp illuminates. Stops in approximately 1 minute. |
| Off | The master warning lamp turns OFF. (vehicle in normal state) | |
| ALC DISP | On | Displays active lane control active status on the information display in the combination meter. |
| Off | Displays active lane control inactive status on the information display in the combination meter. | |
| FL TIRE DISP | On | Displays the front LH tire on the information display in the combination meter. |
| Off | Does not display the front LH tire on the information display in the combination meter. | |
| FR TIRE DISP | On | Displays the front RH tire on the information display in the combination meter. |
| Off | Does not display the front RH tire on the information display in the combination meter. | |
| RL TIRE DISP | On | Displays the rear LH tire on the information display in the combination meter. |
| Off | Does not display the rear LH tire on the information display in the combination meter. | |
| RR TIRE DISP | On | Displays the rear RH tire on the information display in the combination meter. |
| Off | Does not display the rear RH tire on the information display in the combination meter. | |
| TURN DISP | NO DISP | Does not display the turning status on the information display in the combination meter. |
| LH | Displays the LH turning status on the information display in the combination meter. | |
| RH | Displays the RH turning status on the information display in the combination meter. | |
| ALC LEVEL | LEVEL 1 | Displays active lane control corresponding to the selected level on the information display in the combination meter. |
| LEVEL 2 | ||
| LEVEL 3 | ||
| LEVEL 4 | ||
| ALC SETTING | On | Displays active lane control active status on the information display in the combination meter. |
| Off | Displays active lane control inactive status on the information display in the combination meter. | |
| ATC 1 DISP | On | Displays active trace control function active status on the information display in the combination meter. |
| Off | Displays active trace control function inactive status on the information display in the combination meter. | |
| ATC 2 DISP | On | Displays active trace control function active status on the information display in the combination meter. |
| Off | Displays active trace control function inactive status on the information display in the combination meter. | |
| ATC 3 DISP | On | Displays active trace control function active status on the information display in the combination meter. |
| Off | Displays active trace control function inactive status on the information display in the combination meter. | |
| ATC 4 DISP | On | Displays active trace control function active status on the information display in the combination meter. |
| Off | Displays active trace control function inactive status on the information display in the combination meter. | |
| FR shock absorber* | Soft | Controls dynamic digital suspension (FR). |
| Medium | ||
| Hard | ||
| FL shock absorber* | Soft | Controls dynamic digital suspension (FL). |
| Medium | ||
| Hard | ||
| RR shock absorber* | Soft | Controls dynamic digital suspension (RR). |
| Medium | ||
| Hard | ||
| RL shock absorber* | Soft | Controls dynamic digital suspension (RL). |
| Medium | ||
| Hard | ||
| All shock absorber* | Soft | Controls all dynamic digital suspension. |
| Medium | ||
| Hard |
* : Models with digital motion control