Active Test Mode

TEST ITEM

CONDITION

JUDGEMENT

CHECK ITEM (REMEDY)

ENG COOLANT TEMP

• Engine: Return to the original trouble condition
• Change the engine coolant temperature using CONSULT.

If trouble symptom disappears, see CHECK ITEM.

• Harness and connectors
• Engine coolant temperature sensor
• Fuel injector

FUEL INJECTION

• Engine: Return to the original trouble condition
• Change the amount of fuel injection using CONSULT.

If trouble symptom disappears, see CHECK ITEM.

• Harness and connectors
• Fuel injector
• Air fuel ratio (A/F) sensor 1

PURG VOL CONT/V

• Engine: After warming up, run engine at 1, 500 rpm.
• Change the EVAP canister purge volume control solenoid valve opening percent using CONSULT.

Engine speed changes according to the opening percent.

• Harness and connectors
• Solenoid valve

FUEL/T TEMP SEN

Change the fuel tank temperature using CONSULT.

POWER BALANCE

• Engine: After warming up, idle the engine.
• A/C switch OFF
• Selector lever: P or N
• Cut off each injector signal one at a time using CONSULT.

Engine runs rough or dies.

• Harness and connectors
• Compression
• Fuel injector
• Power transistor
• Spark plug
• Ignition coil

EXT V/T ASSIGN ANGLE

• Engine: Return to the original non-standard condition
• Change exhaust valve timing using CONSULT.

If malfunctioning symptom disappears, see CHECK ITEM.

• Harness and connectors
• Exhaust valve timing control solenoid valve

VENT CONTROL/V

• Ignition switch: ON (Engine stopped)
• Turn solenoid valve ON and OFF with the CONSULT and listen to operating sound.

Solenoid valve makes an operating sound.

• Harness and connectors
• Solenoid valve

FAN DUTY CONTROL*

• Ignition switch: ON
• Change duty ratio using CONSULT.

Cooling fan speed changes.

• Harness and connectors
• Cooling fan motor
• Cooling fan relay
• Cooling fan control module
• IPDM E/R

ALTERNATOR DUTY

• Engine: Idle
• Change duty ratio using CONSULT.

Battery voltage changes.

• Harness and connectors
• IPDM E/R
• Alternator

FPCM

• Engine: Return to the original trouble condition
• Select "LOW", "MID" and "HI" with CONSULT.

Fuel pump speed changes or stops.

• Harness and connectors
• Fuel pump control module (FPCM)

IGNITION TIMING

• Engine: Return to the original trouble condition
• Timing light: Set
• Retard the ignition timing using CONSULT.

If trouble symptom disappears, see CHECK ITEM.

Perform Idle Air Volume Learning.

WASTEGATE ACTUATOR

• Ignition switch: ON
• Engine stopped
• Change valve of wastegate actuator target angle using CONSULT

Wastegate valve position sensor voltage changes according to valve target angle

• Harness and connectors
• Electric wastegate control actuator (Removal bypass valve from turbocharger is NG)
• Turbocharger assembly

ENGINE OIL PRESSURE CONTROL SOLENOID VALVE

• Water temperature: >-10 deg.C
• Engine oil temperature: < 120 deg.C (248 deg.F)
• Engine speed: < 4000rpm

Engine oil pressure change

• Harness and connectors
• Engine oil pressure control solenoid valve
• Engine oil pressure sensor
• Engine oil pump

Charge air cooler cooling electric water pump

• Engine: Idle

Change the driving mode of charge air cooler cooling electric water pump.

• Charge air cooler coolant temperature sensor
• Intake air temperature sensor
• Engine oil pressure sensor
• Charge air cooler cooling electric water pump 1, 2

INT V/T ASSIGN ANGLE

• Engine: Return to the original non-standard condition
• Change intake valve timing using CONSULT.

If malfunctioning symptom disappears, see CHECK ITEM.

• Harness and connectors
• Intake valve timing control solenoid valve