Active Test

WARNING: This page is about a different car, the 2018 Infiniti Q60. However, it is still accessible from the selected car via links, so may be relevant.

The active test is used to determine and identify details of a malfunction, based on self-diagnosis test results and data obtained in the DATA MONITOR. In response to instructions from CONSULT, instead of those from chassis control module on the vehicle, a drive signal is sent to the actuator to check its operation.

CAUTION:

Never perform ACTIVE TEST while driving the vehicle.
Always bleed air from brake system before active test.
Never perform active test when system is malfunctioning.

NOTE: During an active test, sometimes a chassis control warning is displayed and the master warning lamp illuminates on the information display in the combination meter; however, this is not a malfunction.

Test item	Operation	Description
BRAKE ACTUATOR 1 MODE 1	Start	Controls brake fluid pressure.
BRAKE ACTUATOR 1 MODE 2	Start	Controls brake fluid pressure.
BRAKE ACTUATOR 1 MODE 3	Start	Controls brake fluid pressure.
BRAKE ACTUATOR 2 MODE 1	Start	Controls brake fluid pressure.
BRAKE ACTUATOR 2 MODE 2	Start	Controls brake fluid pressure.
BRAKE ACTUATOR 2 MODE 3	Start	Controls brake fluid pressure.
BRAKE ACTUATOR 3 MODE 1	Start	Controls brake fluid pressure.
BRAKE ACTUATOR 3 MODE 2	Start	Controls brake fluid pressure.
BRAKE ACTUATOR 3 MODE 3	Start	Controls brake fluid pressure.
ESS RELAY ACTIVE	--	Displayed but not used.
ESS RELAY ACTIVE	--	Displayed but not used.
ESS ACTIVE	--	Displayed but not used.
COMMAND STEERING ANGLE	Start	Transmits the steering command value 0 deg -> 0.00349 deg (hold it for approximately 2 seconds) -> 0 deg (hold it for approximately 2 seconds) -> 0.00349 deg (hold it for approximately 2 seconds) -> 0 deg to the steering force control module.
COMMAND ST WHL FORCE	Start	Transmits the steering reaction force command value 0 N -> 0.6 N (hold it for approximately 2 seconds) -> 0 N (hold it for approximately 2 seconds)-> 0.6 N (hold it for approximately 2 seconds) -> 0 N to the steering force control module.
STOP LAMP OFF RELAY 1 ACTIVE	--	Displayed but not used.
STOP LAMP OFF RELAY 2 ACTIVE	--	Displayed but not used.
MASTER WARNING ACTIVE	On	If touching "On" wit the master warning lamp not illuminated, the master warning lamp illuminates. Stops in approximately 1 minute.
MASTER WARNING ACTIVE	Off	The master warning lamp OFF. (vehicle in normal state)
ALC DISP	On	Displays Active Lane Control active status on the information display in the combination meter.
ALC DISP	Off	Displays Active Lane Control inactive status on the information display in the combination meter.
FL TIRE DISP	On	Displays the front LH tire on the information display in the combination meter.
FL TIRE DISP	Off	Does not display the front LH tire on the information display in the combination meter.
FR TIRE DISP	On	Displays the front RH tire on the information display in the combination meter.
FR TIRE DISP	Off	Does not display the front RH tire on the information display in the combination meter.
RL TIRE DISP	On	Displays the rear LH tire on the information display in the combination meter.
RL TIRE DISP	Off	Does not display the rear LH tire on the information display in the combination meter.
RR TIRE DISP	On	Displays the rear RH tire on the information display in the combination meter.
RR TIRE DISP	Off	Does not display the rear RH tire on the information display in the combination meter.
TURN DISP	NO DISP	Does not display the turning status on the information display in the combination meter.
	LH	Displays the LH turning status on the information display in the combination meter.
	RH	Displays the RH turning status on the information display in the combination meter.
ALC LEVEL	LEVEL 1	Displays Active Lane Control corresponding to the selected level on the information display in the combination meter.
	LEVEL 2
	LEVEL 3
	LEVEL 4
ALC SETTING	On	Displays Active Lane Control active status on the information display in the combination meter.
ALC SETTING	Off	Displays Active Lane Control inactive status on the information display in the combination meter.
ATC 1 DISP	On	Displays active trace control function active status on the information display in the combination meter.
ATC 1 DISP	Off	Displays active trace control function inactive status on the information display in the combination meter.
ATC 2 DISP	On	Displays active trace control function active status on the information display in the combination meter.
ATC 2 DISP	Off	Displays active trace control function inactive status on the information display in the combination meter.
ATC 3 DISP	On	Displays active trace control function active status on the information display in the combination meter.
ATC 3 DISP	Off	Displays active trace control function inactive status on the information display in the combination meter.
ATC 4 DISP	On	Displays active trace control function active status on the information display in the combination meter.
ATC 4 DISP	Off	Displays active trace control function inactive status on the information display in the combination meter.
FR shock absorber ^*	Soft	Controls dynamic digital suspension (FR).
	Medium
	Hard
FL shock absorber ^*	Soft	Controls dynamic digital suspension (FL).
	Medium
	Hard
RR shock absorber ^*	Soft	Controls dynamic digital suspension (RR).
	Medium
	Hard
RL shock absorber ^*	Soft	Controls dynamic digital suspension (RL).
	Medium
	Hard
All shock absorber ^*	Soft	Controls all dynamic digital suspension.
	Medium
	Hard

*: Models with digital motion control