Confirmation/Adjustment Mode

Start the diagnosis function and select "Confirmation/Adjustment". The confirmation/adjustment mode indicates where each item can be checked or adjusted.
Select each switch on the "Confirmation/Adjustment Mode" screen to display the relevant trouble diagnosis screen. Touch the "Back" to return to the initial Confirmation/Adjustment Mode screen.

Display Diagnosis

Confirmation of the Display Control Unit screen and integral switch screen.

Item		Description
Display Settings	Color Spectrum Bar	Display 8 colors of following bars. White Yellow Cyan (Close to light blue) Green Magenta (Close to purplish red) Red Blue Black Gray Scale
	Gradation Bar	Display 64 gradation gray-scale image to a screen.
	White Display	Display white screen.
	Black Display	Display black screen.
Touch Panel		The function can check the presence of a "+" indication and deviation from where it should be while touching the touch panel. Display coordinates and gesture operation name (Drag, Tap, Double Tap, Spread, etc.) of the screen which touched.
Sensor Sensitivity Setting		Display a current touch panel sensor sensitivity set value. Can change the touch panel sensor sensitivity set value with 1 (Low) - 5 (high) phases.

Vehicle Signals

A comparison check can be made of each actual vehicle signal and the signals recognized by the system.

Display Control Unit

Diagnosis item	Display	Vehicle status	Remarks
Vehicle Speed	ON	Vehicle speed > 0 km/h (0 MPH)	Changes in indication may be delayed. This is normal.
Vehicle Speed	OFF	Vehicle speed = 0 km/h (0 MPH)
Parking Brake Signal	ON	Parking brake is applied.
Parking Brake Signal	OFF	Parking brake is released.
Light Signal	ON	Block the light beam from the auto light optical sensor when the light switch is ON.	--
Light Signal	OFF	Either of the following conditions Lighting switch OFF. Expose the auto light optical sensor to light when the light switch is ON.	--
Ignition Signal	ON	Ignition switch ON.	--
Ignition Signal	OFF	Ignition switch in ACC position.	--
Reverse Signal	ON	Shift the selector lever to "R" position.	Changes in indication may be delayed. This is normal.
Reverse Signal	OFF	Shift the selector lever other than "R" position.	Changes in indication may be delayed. This is normal.

Navigation

Diagnosis item	Display	Vehicle status	Remarks
Vehicle Speed	ON	Vehicle speed > 0 km/h (0 MPH)	Changes in indication may be delayed. This is normal.
Vehicle Speed	OFF	Vehicle speed = 0 km/h (0 MPH)	Changes in indication may be delayed. This is normal.
Ignition Signal	ON	Ignition switch ON.	--
Ignition Signal	OFF	Ignition switch in ACC position.	--
Reverse Signal	ON	Shift the selector lever to "R" position.	Changes in indication may be delayed. This is normal.
Reverse Signal	OFF	Shift the selector lever other than "R" position.	Changes in indication may be delayed. This is normal.

### Speaker Test

Select "### Speaker Test" to display the speaker diagnosis screen. Touch "Start" to generate a test tone in a speaker. Touch "Next" to generate a test tone in the next speaker. Touch "End" to stop the test tones.

Navigation

Item	Description
Sensor Information	The reception status of GPS can be confirmed.
Route Simulation	Set the display ON/OFF of the "simulation" menu of the navigation.

Error History

The self-diagnosis results are judged depending on whether any error occurs from when "Self-diagnosis" is selected until the self-diagnosis results are displayed.

However, the diagnosis results are judged normal if an error has occurred before the Ignition Switch is turned ON and then no error has occurred until the self-diagnosis start. Check the "Error Record" to detect any error that may have occurred before the self-diagnosis start because of this situation.

The error record displays the time and place of the most recent occurrence of that error. However, take note of the following points.

Place of the error occurrence is represented by the longitude and latitude at the time an error occurred. If current location mark has deviated from the correct position, then the place of the error occurrence cannot be located correctly.
The frequency of occurrence is displayed in a up-and-down manner.

Count up method

The counter resets to 0 if an error occurs when Ignition Switch is turned ON. The counter increases by 1 if the condition is normal at a next ignition ON cycle.
The counter upper limit is 39. Any counts exceeding 39 are ignored." The counter can be reset (no error record display) with the "Delete log" switch or CONSULT.

Display type of occurrence frequency	Error history display item
Count up method	CAN communication line, Control Unit (CAN), AV communication line, Control Unit (AV)

Error item

Some error items may be displayed simultaneously according to the cause. If some error items are displayed simultaneously, the detection of the cause can be performed by the combination of display items

AV COMM Diagnosis

AV COMM Monitor

Displays the communication status between Display Control Unit (master unit) and each unit.
The error counter displays "OK" if any malfunction was not detected in the past and displays "0" if a malfunction is detected. It increases by 1 if the condition is normal at the next Ignition Switch ON cycle. The upper limit of the counter is 39.

The error counter is erased if "Reset" is pressed.

Items	Status (Current)	Counter (Past)
CMF Send Switch	OK / UNKW	OK / 0 - 39 / --
CMF Receive Switch	OK / UNKW	OK / 0 - 39 / --
CMF Receive Bose® Amp	OK / UNKW	OK / 0 - 39 / --
CMF Receive AVM	OK / UNKW	OK / 0 - 39 / --
CMF Receive Meter	OK / UNKW	OK / 0 - 39 / --
CMF Receive TCU2	OK / UNKW	OK / 0 - 39 / --
CMF Receive Audio	OK / UNKW	OK / 0 - 39 / --
CMF Receive RSE	OK / UNKW	OK / 0 - 39 / --

Clock Setting

The date and time information can be adjusted.

Camera Control

Item	Description
Adjust Guide Line of Rear View Cam	The guiding lines in the rear view monitor can be adjusted.
Check/Change Configuration	Displays the current configuration data.
Reset Configuration	Initializes the camera system configuration.
Camera System Type	Sets the type of camera that is connected.

SXM

XM Mode Diagnosis

Item	Description
Show XM Diagnosis	Display adjustment items to test satellite radio function.
External Connection Mode	Set in external diagnostic mode.

Delete Unit Connection Log

Deletes any unit connection records and error records from the Display Control Unit memory. (Clear the records of the unit that has been removed.)

Reset Settings

Item	Description
Reset User Data	Initializes the Display Control Unit, NAVI Control Unit and AV Control Unit memory.
Reset Configuration	Initializes the configuration data.

Version Information

Version information of the each Control Unit and switch is displayed.

Program Update

Version of the Display Control Unit can be update.

### Hands-Free Phone

The hands-free phone reception volume adjustment and microphone and speaker test functions are also available.

Item	Description
Handsfree Volume	The reception volume can be set in three steps: "Low", "Standard" and "High".
### Voice Microphone Test	The microphone audio can be directly connected to the speakers to perform a microphone test.
Onload model ID	Displays the on board unit ID.