Work Procedure

WARNING: This page is about a different car, the 2019 Nissan Armada and 2018 Nissan Armada. However, it is still accessible from the selected car via links, so may be relevant.

WARNING: Be careful of traffic conditions and safety around the vehicle when performing road test.

CAUTION: Fully understand the following items well before the road test;

Precautions: Refer to Blind Spot Warning/Intelligent Blind Spot Intervention System Service .
System description for Blind Spot Warning: Refer to System Description .
System description for Intelligent Blind Spot Intervention: Refer to System Description .
Normal operating condition: Refer to Description .

LDW/INTELLIGENT LANE INTERVENTION SYSTEM ACTION TEST
Perform the LDW/Intelligent Lane Intervention system action test. Refer to Work Procedure .

GO TO 2 .
CHECK BSW SYSTEM SETTING
1. Start the engine.
2. Check that the BSW system setting can be enabled/disabled on the integral switch.
3. Turn OFF the ignition switch and wait for 5 seconds or more.
4. Check that the previous setting is saved when the engine starts again.
GO TO 3 .

BSW SYSTEM ACTION TEST

Enable the setting of the BSW system on the integral switch.
Turn warning systems switch ON (warning systems ON indicator is ON).
NOTE: Intelligent Blind Spot Intervention system is OFF.

Check BSW operation according to the following table.

Vehicle condition/ Driver's operation				Action
Warning systems ON indicator	Vehicle speed	Turn signal condition	Status of vehicle detection within detection area	Indication on the Blind Spot Warning/Intelligent Blind Spot Intervention indicator	Buzzer
OFF	-	-	-	OFF	OFF
ON	Less than approx. 29 km/h (18 MPH)	-	-	OFF	OFF
	Approx. 32 km/h (20 MPH)	-	Vehicle is absent	OFF	OFF
		OFF	Vehicle is detected	ON	OFF
		ON (vehicle detected direction)	Before turn signal operates Vehicle is detected	Blink Courtesy of NISSAN NORTH AMERICA, INC.	Short continuous beep Courtesy of NISSAN NORTH AMERICA, INC.
		ON (vehicle detected direction)	Vehicle is detected after turn signal operates	Blink Courtesy of NISSAN NORTH AMERICA, INC.	OFF

NOTE:

If vehicle speed exceeds approximately 32 km/h (20 MPH), BSW function operates until the vehicle speed becomes lower than approximately 29 km/h (18 MPH).
Time shown in the figure is approximate time.
Always Intelligent Blind Spot Intervention system operates together with BSW system. Whenever Intelligent Blind Spot Intervention system is turned on by pushing the dynamic driver assistance switch, BSW system also be turned on even if the BSW system is turned off. However, at this time the warning systems ON indicator remains OFF.

GO TO 4 .

CHECK INTELLIGENT BLIND SPOT INTERVENTION SYSTEM SETTING
1. Start the engine.
2. Check that the Intelligent Blind Spot Intervention system setting can be enabled/disabled on the integral switch.
3. Turn OFF the ignition switch and wait for 5 seconds or more.
4. Check that the previous setting is saved when the engine starts again.
GO TO 5 .
CHECK DYNAMIC DRIVER ASSISTANCE SWITCH
1. Start the engine.
2. After starting the engine wait for 5 seconds or more.
3. Enable the setting of the Intelligent Blind Spot Intervention system on the integral switch.
4. Press the dynamic driver assistance switch.
5. Check that the Intelligent Blind Spot Intervention ON indicator on the combination meter illuminates.
6. Check that the Intelligent Blind Spot Intervention ON indicator turns OFF when the system is turned OFF by pressing the dynamic driver assistance switch.
7. Check that the Intelligent Blind Spot Intervention ON indicator turns OFF when the engine starts again.
NOTE:
- The Intelligent Blind Spot Intervention ON indicator does not illuminate even when the dynamic driver assistance switch is turned ON within approximately 5 seconds after starting the engine.
- When the Intelligent Blind Spot Intervention system setting is disabled on the integral switch, the Intelligent Blind Spot Intervention ON indicator is not turned ON by pressing the dynamic driver assistance switch.
INSPECTION END