Data Monitor

Monitor Item [Unit]

Main

Description

REQ SW -DR [On/Off]

x

Indicates condition of door request switch LH.

REQ SW -AS [On/Off]

x

Indicates condition of door request switch RH.

REQ SW -BD/TR [On/Off]

x

Indicates condition of back door request switch.

PUSH SW [On/Off]

Indicates condition of push-button ignition switch.

BRAKE SW 1 [On/Off]

x

Indicates condition of brake pedal position switch.

BRAKE SW 2 [On/Off]

Indicates condition of stop lamp switch.

DETE/CANCL SW [On/Off]

x

Indicates condition of park position switch.

PUSH SW -IPDM [On/Off]

Indicates condition of push-button ignition switch received from IPDM E/R on CAN communication line.

IGN RLY1 -F/B [On/Off]

Indicates condition of ignition relay 1 received from IPDM E/R on CAN communication line.

SFT PN -IPDM [On/Off]

Indicates condition of P (park) or N (neutral) position from TCM on CAN communication line.

STARTER RELAY -IPDM [On/Off]

Indicates condition of starter relay received from IPDM E/R on CAN communication line.

ENGINE STATE [STOP/START/CRANK/RUN]

x

Indicates condition of engine state from ECM on CAN communication line.

ST/INH RELAY - IPDM [On/Off]

Indicates condition of starter relay and starter control relay status signal from IPDM E/R.

REVERSE SIGNAL -IPDM [On/Off]

Indicates condition of transmission range switch received from IPDM E/R on CAN communication line.

CRANKING PERMIT -ECM [PERMIT]

Indicates condition of engine start possibility from ECM on CAN communication line.

STARTER CUT RELAY -ECM [On/Off]

Indicates condition of starter cut relay from ECM on CAN communication line.

VEH SPEED 1 [mph/km/h]

x

Indicates condition of vehicle speed signal received from ABS on CAN communication line.

VEH SPEED 2 [mph/km/h]

x

Indicates condition of vehicle speed signal received from combination meter on CAN communication line.

IGN REQ -IPDM [On/Off]

Indicates condition of ignition request from IPDM E/R on CAN communication line.

STARTER REQ -IPDM [On/Off]

Indicates condition of starter request received from IPDM E/R on CAN communication line.

DOOR STAT -DR [LOCK/READY/UNLK]

x

Indicates condition of driver side door status.

DOOR STAT -AS [LOCK/READY/UNLK]

x

Indicates condition of passenger side door status.

DOOR STAT -RR [LOCK/READY/UNLK]

x

Indicates condition of rear right side door status.

DOOR STAT -RL [LOCK/READY/UNLK]

x

Indicates condition of rear left side door status.

ID OK FLAG [Set/Reset]

Indicates condition of Intelligent Key ID.

PRMT ENG STRT [Set/Reset]

Indicates condition of engine start possibility.

PRMT RKE STRT [Set/Reset]

Indicates condition of engine start possibility from Intelligent Key.

I-KEY OK FLAG [Key ON/Key OFF]

x

Indicates condition of Intelligent Key OK flag.

PRBT ENG STRT [Set/Reset]

Indicates condition of engine start prohibit.

ID AUTHENT CANCEL TIMER [STOP]

Indicates condition of Intelligent Key ID authentication.

CRNK PRBT TMR [On/Off]

Indicates condition of crank prohibit timer.

AUT CRNK TMR [On/Off]

Indicates condition of automatic engine crank timer from Intelligent Key.

CRNK PRBT TME [sec]

Indicates condition of engine crank prohibit time.

AUTO CRNK TME [sec]

Indicates condition of automatic engine crank time from Intelligent Key.

CRANKING TME [sec]

Indicates condition of engine cranking time from Intelligent Key.

RKE OPE COUN1 [0-19]

x

When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the numerical value start changing.

RKE-LOCK [On/Off]

Indicates condition of lock signal from Intelligent Key.

RKE-UNLOCK [On/Off]

Indicates condition of unlock signal from Intelligent Key.

RKE-PANIC [On/Off]

Indicates condition of panic signal from Intelligent Key.

RKE-MODE CHG [On/Off]

Indicates condition of mode change signal from Intelligent Key.

RKE PBD [On/Off]

Indicates condition of automatic back door signal from Intelligent Key.