CONSULT Function
APPLICABLE ITEM
| Mode | Function |
|---|---|
| All DTC Reading | Display all DTCs or diagnostic items that all ECUs are recording and judging. |
| CAN Diagnosis | This mode displays a network diagnosis result about CAN by diagram. |
| CAN Diagnosis Support Monitor | It monitors the status of CAN communication. |
| Self Diagnostic Results | The ECU self diagnostic results are displayed. |
| Data Monitor | The ECU input/output data is displayed in real time. |
| ECU Identification | The ECU part number is displayed. |
SELF DIAGNOSTIC RESULTS
Display Item List
Refer to DTC Index .
How to Read DTC
DTC is displayed on "Self Diagnostic results" of CONSULT. When DTC is currently detected, "CRNT" is displayed. If "PAST" is displayed, it shows a malfunction occurred in the past. The trip number of drive without malfunction of concerned DTC can be confirmed with "IGN counter" inside "FFD".
How to Erase DTC
NOTE:
If the ignition switch is left ON after repair, turn OFF the ignition switch and wait for 10 seconds or more. Then, turn the ignition ON again. (Engine stop)
- Touch "SHIFT" of CONSULT.
- Touch "Self Diagnostic Result".
- Touch "Erase". (DTC memorized in electric shift control module is erased.)
Freeze Frame Data (FFD)
The following vehicle status is recorded when DTC is detected and is displayed on CONSULT.
| Monitored item | Displayed contents |
|---|---|
| ODO/TRIP METER | Displays the mileage at the time the malfunction is detected. |
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items.
| Monitored item | (Unit) | Remarks |
|---|---|---|
| SHIFT SENSOR 1 | Displays the signal value of electric shift sensor No. 1 | |
| SHIFT SENSOR 2 | Displays the signal value of electric shift sensor No. 2 | |
| SHIFT SENSOR 3 | Displays the signal value of electric shift sensor No. 3 | |
| SHIFT SENSOR 4 | Displays the signal value of electric shift sensor No. 4 | |
| SHIFT SENSOR 5 | Displays the signal value of electric shift sensor No. 5 | |
| SHIFT SENSOR 6 | Displays the signal value of electric shift sensor No. 6 | |
| P POSITION SWITCH 1 | Displays the signal value of P position switch No. 1 | |
| P POSITION SWITCH 2 | Displays the signal value of P position switch No. 2 | |
| BRAKE SWITCH | Displays the signal value of the stop lamp switch | |
| PARKING ACTUATOR RELAY A | Displays the command value from the electric shift control module to shift actuator relay A | |
| PARKING ACTUATOR RELAY B | Displays the command value from the electric shift control module to shift actuator relay B | |
| NOT P POSITION CONDITION | Displays a status other than the P position recognized by the electric shift control module | |
| IGNITION SWITCH | Displays the input status of the power switch | |
| BRAKE SWITCH (CAN) | Displays the signal value of the stop lamp switch received from BCM. | |
| Shift sensor 7 | Displays the signal value of electric shift sensor No. 7 | |
| Shift sensor 8 | Displays the signal value of electric shift sensor No. 8 | |
| ECU POWER 1 | Monitors the power supply of electric shift control module and displays the status | |
| MAIN POWER VOLTAGE | (V) | Monitors the voltage value of the main power supply for the electric shift control module and displays the monitored value |
| MOTOR A U VOLTAGE | (V) | Displays the motor A U-phase terminal voltage A/D converted value |
| MOTOR A V VOLTAGE | (V) | Displays the motor A V-phase terminal voltage A/D converted value |
| MOTOR A W VOLTAGE | (V) | Displays the motor A W-phase terminal voltage A/D converted value |
| MOTOR B U VOLTAGE | (V) | Displays the motor B U-phase terminal voltage A/D converted value |
| MOTOR B V VOLTAGE | (V) | Displays the motor B V-phase terminal voltage A/D converted value |
| MOTOR B W VOLTAGE | (V) | Displays the motor B W-phase terminal voltage A/D converted value |
| RANGE POSITION | Displays the position recognized by the electric shift control module | |
| SHIFT POSITION JUDGMENT | Displays the shift input position recognized by the electric shift control module | |
| TARGET SHIFT POSITION | Displays the target shift position recognized by the electric shift control module | |
| Ds mode | Displays the status of manual mode request signal | |
| Actual shift position | Displays the shift position signal received from TCM | |
| VEHICLE SPEED (VDC) | (km/h or mph) | Displays the signal value of the vehicle speed received from ABS actuator control unit |
| Vehicle speed (CVT) | (km/h or mph) | Displays the signal value of the vehicle speed received from TCM |
| E-SHIFT WARNING LAMP | Displays the electric shift warning lamp signal status transmitted from the electric shift control module | |
| Power supply voltage | Displays the status of battery voltage | |
| E-SHIFT WARNING MSG | Displays the master warning message status transmitted from the electric shift control module | |
| SHIFT SENSOR 1 VOLTAGE | (V) | Displays the voltage value of electric shift sensor No. 1 |
| SHIFT SENSOR 2 VOLTAGE | (V) | Displays the voltage value of electric shift sensor No. 2 |
| SHIFT SENSOR 3 VOLTAGE | (V) | Displays the voltage value of electric shift sensor No. 3 |
| SHIFT SENSOR 4 VOLTAGE | (V) | Displays the voltage value of electric shift sensor No. 4 |
| SHIFT SENSOR 5 VOLTAGE | (V) | Displays the voltage value of electric shift sensor No. 5 |
| SHIFT SENSOR 6 VOLTAGE | (V) | Displays the voltage value of electric shift sensor No. 6 |
| Park position SW 1 voltage | (V) | Displays the voltage value of P position switch No. 1 |
| Park position SW 2 voltage | (V) | Displays the voltage value of P position switch No. 2 |
| Shift sensor 7 voltage | (V) | Displays the voltage value of electric shift sensor No. 7 |
| Shift sensor 8 voltage | (V) | Displays the voltage value of electric shift sensor No. 8 |