DTC Diagnosis Procedure

With CONSULT

1. Turn ignition switch ON.
2. Select "Data Monitor" in "SHIFT".
3. Select "SHIFT SENSOR 1", "SHIFT SENSOR 2", "SHIFT SENSOR 3", "SHIFT SENSOR 4", "SHIFT SENSOR 5", "SHIFT SENSOR 6", "Shift sensor 7", and "Shift sensor 8".
4. Operate the selector lever to identify a electric shift sensor of which value does not change.

   Monitor item	Condition	Value / Status
   SHIFT SENSOR 1	Selector lever is held in R position	On
   	Other than the above	Off
   SHIFT SENSOR 2	Selector lever is held in R and Nr positions	On
   	Other than the above	Off
   SHIFT SENSOR 3	Selector lever is held in H (Home) and Nr positions	On
   	Other than the above	Off
   SHIFT SENSOR 4	Selector lever is held in H (Home) and Nr positions	On
   	Other than the above	Off
   SHIFT SENSOR 5	Selector lever is held in H (Home) and Nd positions	On
   	Other than the above	Off
   SHIFT SENSOR 6	Selector lever is held in H (Home) and Nd positions	On
   	Other than the above	Off
   Shift sensor 7	Selector lever is held in D/M and Nd positions	On
   	Other than the above	Off
   Shift sensor 8	Selector lever is held in D/M position	On
   	Other than the above	Off

Without CONSULT

1. Turn ignition switch ON.
2. Operate the selector lever.
3. Check the voltage between the electric shift control module vehicle side harness connector terminal and ground.

   Electric shift sensor	+		-	Condition	Voltage(Approx.)
   	Electric shift control module
   	Connector	terminal
   1	M241	34	Ground	Selector lever is held in R position	0 V
   				Other than the above	5 V
   2		35		Selector lever is held in R and Nr positions	0 V
   				Other than the above	5 V
   3		36		Selector lever is held in H (Home) and Nr positions	0 V
   				Other than the above	5 V
   4		37		Selector lever is held in H (Home) and Nr positions	0 V
   				Other than the above	5 V
   5		44		Selector lever is held in H (Home) and Nd positions	0 V
   				Other than the above	5 V
   6		45		Selector lever is held in H (Home) and Nd positions	0 V
   				Other than the above	5 V
   7		39		Selector lever is held in D/M and Nd positions	0 V
   				Other than the above	5 V
   8		40		Selector lever is held in D/M position	0 V
   				Other than the above	5 V

Is the inspection results normal?

>>

INSPECTION END

>>

GO TO 2.

1. Turn ignition switch OFF.
2. Disconnect the electric shift control module connector.
3. Disconnect the electric shift selector connector.
4. Check the continuity between the electric shift control module vehicle side harness connector terminal and the electric shift selector vehicle side harness connector terminal.

   Electric shift sensor	Electric shift control module		Electric shift selector		Continuity
   	Connector	terminal	Connector	terminal
   1	M241	34	M251	2	Existed
   3		36		3
   5		44		4
   7		39		5
   2		35		14
   4		37		15
   6		45		16
   8		40		17

5. Check the continuity between the electric shift control module vehicle side harness connector terminals and ground.

   Electric shift sensor	Electric shift control module		Ground	Continuity
   	Connector	terminal
   1	M241	34	Ground	Not existed
   3		36
   5		44
   7		39
   2		35
   4		37
   6		45
   8		40

Is the inspection result normal?

>>

Replace the electric shift selector. Refer to Removal and Installation .

>>

Repair or replace damaged parts.