Specifications Index
LIBERTY SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | 100 Ft. Lbs. (136 N.m) | ||
| Brakes | |||
| Bleeding Sequence | |||
| With ABS | STANDARD PROCEDURE - ABS BRAKE BLEEDING | ||
| Without ABS | BLEEDING SEQUENCE | ||
| Disc Brakes | DISC BRAKE SPECIFICATIONS | ||
| Drum Brakes | DRUM BRAKE SPECIFICATIONS | ||
| Torque | LIBERTY | ||
| Charging | |||
| Generator | GENERATOR APPLICATION | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | |||
| 2.4L | DRIVE BELT | ||
| 3.7L | DRIVE BELT | ||
| Belt Routing | |||
| 2.4L | See Figures under INSTALLATION . | ||
| 3.7L | See Figure under REMOVAL . | ||
| Engine Cooling | |||
| General Service Specifications | |||
| 2.4L | Capacity - 11.0 Qts. (10.4L). For additional information, see COOLING SYSTEM - 2.4L | ||
| 3.7L | Capacity - 11.0 Qts. (10.4L). For additional information, see COOLING SYSTEM - 3.7L . | ||
| Radiator Cap Pressure | 18-21 psi | ||
| Thermostat R & I | |||
| 2.4L | ENGINE COOLANT THERMOSTAT | ||
| 3.7L | ENGINE COOLANT THERMOSTAT | ||
| Water Pump R & I | |||
| 2.4L | WATER PUMP | ||
| 3.7L | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | |||
| 2.4L (CAUTION: If oil pressure is zero at curb idle, DO NOT run engine at 3000 RPM.) | Oil pressure at curb idle (minimum) is 4 psi (25 kPa). Oil pressure at 3000 RPM is 25-80 psi (170-550 kPa). | ||
| 3.7L (CAUTION: If oil pressure is zero at curb idle, DO NOT run engine at 3000 RPM.) | Oil pressure at curb idle (minimum) is 4 psi (25 kPa). Oil pressure at 3000 RPM is 25-110 psi (170-758 kPa). | ||
| Overhaul | |||
| 2.4L | See Figures under ENGINE SPECIFICATIONS . | ||
| 3.7L | See Figures under ENGINE SPECIFICATIONS . | ||
| Torque | |||
| 2.4L | TORQUE SPECIFICATIONS | ||
| 3.7L | See Figures under TORQUE SPECIFICATIONS . | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Drive Plate/Flex Plate Torque | |||
| 2.4L | 60 Ft. Lbs. (81 N.m) | ||
| 3.7L | 45 Ft. Lbs. (60 N.m) | ||
| Fuel System | |||
| Fuel Filter Location | FUEL FILTER | ||
| Pressure Specifications | FUEL PUMP | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE TEST | ||
| Fuel Pressure Release Procedure | FUEL SYSTEM PRESSURE RELEASE | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | HIGH TENSION WIRE RESISTANCE | ||
| Ignition Wires (Routing) | FIRING ORDER Wire routing is located in Figures. | ||
| Spark Plugs | SPARK PLUGS | ||
| Starting | |||
| Starter | GENERATOR RATINGS -- GAS ENGINES | ||
| Torque | TORQUE -- EXCEPT DIESEL | ||
| Wheel Alignment | |||
| Adjustment Specifications | ALIGNMENT SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Lug Nut Torque | 85-115 Ft. Lbs. (115-156 N.m) | ||