Common Specs & Procedures
CADENZA COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SPECIFICATION | ||
| Torque | Refer to Tightening Torque in text in appropriate HVAC article. | ||
| Axle Nut/Hub Nut | |||
| Front | 240.3-269.7 N.m (24.5-27.5 kgf.m, 177.2- 198.9 lb. ft.) | ||
| Rear | N/A | ||
| Battery | BATTERY | ||
| Brakes | |||
| Bleeding Sequence | Refer to BLEEDING OF BRAKE SYSTEM . | ||
| Disc Brakes | |||
| Service Specifications | SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUES | ||
| Drum Brakes | |||
| Service Specifications | N/A | ||
| Torque | N/A | ||
| Charging | |||
| Generator | ALTERNATOR | ||
| Torque | Refer to TIGHTENING TORQUES SPECIFICATIONS table under STARTING SYSTEM . | ||
| Drive Belts | |||
| Adjustment | REMOVAL AND INSTALLATION | ||
| Drive Belt Routing | Refer to Drive Belt Routing figure under REMOVAL AND INSTALLATION . | ||
| Engine Cooling | |||
| General Service Specifications | Refer to Cooling System in chart under SPECIFICATIONS | ||
| Radiator Cap Pressure | 13.51-17.78 psi (93.16-122.58 kPa) | ||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | COMPRESSION TEST | ||
| Oil Pressure | 130 kPa (1.32 kgf/cm2 , 18.77 psi) at 1000 RPM, 110°C (230°F) | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUES | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 71.54-75.46 N.m (52.80-55.69) | ||
| Fuel System | |||
| Pressure Specification | 343-500 kPa (3.5-5.1 kgf/cm2 , 49.8-72.5 psi) | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE TEST (LOW PRESSURE SYSTEM) | ||
| Fuel Filter Location | Fuel filter is part of fuel pump module | ||
| Fuel Filter R & I | FUEL FILTER | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil on plug. Refer to IGNITION COIL . | ||
| Ignition Wires (Routing) | Coil on plug. | ||
| Spark Plug | |||
| Type: SILZKR7B11 | |||
| Gap | 1.0-1.1 mm (0.0394-0.0433 in.) | ||
| Torque | 14.7-24.5 N.m (1.5-2.5 kgf.m, 10.8-18.0 lb-ft) | ||
| Starting | |||
| Starter | Refer to STARTING SYSTEM . | ||
| Torque | Refer to TIGHTENING TORQUES SPECIFICATIONS table under STARTING SYSTEM . | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT | ||
| Torque | TIGHTENING TORQUES | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 88.2-107.8 N.m (9.0-11.0 kgf.m, 65.0-79.5 lb-ft) | ||