Repair Procedures: Removal

Remove the air cleaner assembly.
(Refer to "AIR CLEANER .")
Remove the battery and battery tray.
(Refer to "BATTERY .")
Remove the ground line after removing the bolt (A).

Courtesy of
Disconnect the solenoid valve connector (A) and inhibitor switch connector (B).

Courtesy of
Disconnect the Electric Oil Pump (EOP) connector (A).

Courtesy of
Remove the wiring brackets (A, B, C).
Tightening torque:

(A, C) 9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

(B) 14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.8 ~ 15.9 lb-ft)

Courtesy of

Courtesy of
Remove the shift cable (C) after removing the nut (A) and bolts (B).
Tightening torque:
1. 9.8 ~ 13.7 N.m (1.0 ~ 1.4 kgf.m, 7.2 ~ 10.1 lb-ft)
2. 14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.9 ~ 15.9 lb-ft)
Courtesy of
Disconnect the hose (B) after removing the automatic transaxle fluid cooler hose clamp (A).

Courtesy of
Remove the automatic transaxle upper mounting bolts (A) and the starter mounting bolts (B).
Tightening torque:
1. 42.2 ~ 54.0 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)
2. 49.0 ~ 63.7 N.m (5.0 ~ 6.5 kgf.m, 36.2 ~ 47.0 lb-ft)
Courtesy of
Install the engine support fixture.
1. Loosen the bolts (A) from both side.
2. Assemble the engine support fixture.
  (Refer to "AUTOMATIC TRANSAXLE SYSTEM - GENERAL INFORMATION - 2.0L .")
Courtesy of
Remove the cover (A).

Courtesy of
Remove the transaxle mounting bracket bolts (A).
Tightening torque:

88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.8 lb-ft)

Courtesy of
Remove the transaxle support bracket (A).
Tightening torque:

58.9 ~ 78.5 N.m (6.0 ~ 8.0 kgf.m, 43.4 ~ 57.9 lb-ft)

Courtesy of
Lift the vehicle with a jack.
Remove the under cover and side cover.
(Refer to "ENGINE ROOM UNDER COVER .")
Remove the drive shaft assembly.
(Refer to "FRONT DRIVESHAFT .")
Remove the heat protector (A).
Tightening torque:

19.6 ~ 29.4 N.m (2.0 ~ 3.0 kgf.m, 14.5 ~ 21.7 lb-ft)

Courtesy of
Remove the air guide bracket (A).
Tightening torque:

8.8 ~ 13.7 N.m (0.9 ~ 1.4 kgf.m, 6.5 ~ 10.1 lb-ft)

Courtesy of
Remove the dust cover (A).
Tightening torque:

42.2 ~ 53.9 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)

Courtesy of
Remove the torque converter mounting bolts (A) with rotating the crankshaft.
Tightening torque:

45.1 ~ 52.0 N.m (4.6 ~ 5.3 kgf.m, 33.3 ~ 38.3 lb-ft)

Courtesy of
Remove the roll rod bracket (C) after removing bolts (A, B).
Tightening torque:
1. 49.0 ~ 63.7 N.m (5.0 ~ 6.5 kgf.m, 36.2 ~ 47 lb-ft)
2. 107.9 ~ 127.5 N.m (11.0 ~ 13.0 kgf.m, 79.6 ~ 94 lb-ft)
Courtesy of
Remove the mounting bolts (A, B) after supporting the transaxle by a jack.
Tightening torque:
1. 42.2 ~ 48.1 N.m (4.3 ~ 4.9 kgf.m, 31.1 ~ 35.4 lb-ft)
2. 42.2 ~ 53.9 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)
Courtesy of
Remove the transaxle while slowly lower the jack.
NOTE: Be careful not to damage other system or parts near by when removing the transaxle assembly.