Timing Belt: Installation

1. Align the pulley set key with the key groove of the pulley.
   Fig 1: Aligning Pulley Set Key With Key Groove Of Pulley

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Slide on the timing pulley facing the flange side inward.
   NOTE: Do not scratch the sensor part of the crankshaft timing pulley.
3. Install the timing belt plate with the bolt.
   1. Torque: 8.0 N.m (80 kgf.cm, 71 in..lbf) 
   Fig 2: Installing Timing Belt Plate With Bolt

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Apply adhesive to 2 or 3 threads of the pivot bolt.
   1. Adhesive: Part No. 08833-00080, THREE BOND 1344, LOCTITE 242 or equivalent 
      Fig 3: Applying Adhesive To Threads Of Pivot Bolt

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Using a 10 mm hexagon wrench, install the plate washer and pulley with the pivot bolt.
   1. Torque: 35 N.m (350 kgf.cm, 26 ft.lbf) 
3. Check that the pulley bracket moves smoothly.

1. Use the crankshaft pulley bolt to turn the crankshaft, and align the dot mark on the crankshaft timing pulley and the timing mark on the oil pump body.
   Fig 4: Aligning Dot Mark On Crankshaft Timing Pulley And Timing Mark

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Remove any oil or water on the crankshaft timing pulley and idler pulley, and keep them clean.
3. Install the timing belt on the crankshaft timing pulley and idler pulley.

   HINT:

   When re-using timing belt:

   Align the matchmarks of the crankshaft timing pulley and timing belt, and install the belt with the arrow pointing in the direction of engine revolution.

Fig 5: Installing Belt With Arrow Pointing In Direction Of Engine Revolution

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install the guide, facing the cup side outward.

1. Install the gasket to the timing belt cover.
2. Install the timing belt cover with the 5 bolts.
   1. Torque: 8.0 N.m (80 kgf.cm, 71 in..lbf) 

Fig 6: Installing Timing Belt Guide

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Align the pulley set key with the key groove of the pulley, and slide on the pulley.
2. Check that the sub timing mark (60° mark BTDC) of the crankshaft pulley is aligned with the timing mark "0" of the No. 1 timing belt cover.

   HINT:

   At this time, the crankshaft pulley set key groove and the timing mark (TDC mark) of the crankshaft pulley are as shown in Fig 7 .

   Fig 7: Installing Crankshaft Pulley

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Temporarily install the pulley bolt.

1. Align the camshaft knock pin with the VVT-i pulley, and push the VVT-i pulley by hand until you feel it touch the bottom.
   Fig 8: Aligning Camshaft Knock Pin With VVT-I Pulley

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Check that the outer circumference of the VVT-i pulley easily rotates through 30°.
   Fig 9: Checking Rotation Of Outer Circumference Of VVT-I Pulley

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Holding the hexagon portion of the camshaft with a wrench.
4. Using a 10 mm hexagon wrench, and the set bolt.
   1. Torque: 81 N.m (810 kgf.cm, 60 ft.lbf) 
5. Using a 14 mm hexagon wrench, install the straight screw plug with the seal washer to the set bolt.
   1. Torque: 15 N.m (150 kgf.cm, 11 ft.lbf) 
      Fig 10: Installing Straight Screw Plug With Seal Washer To Set Bolt

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Align the dot mark on the camshaft timing pulley with the timing mark of the No. 4 timing belt cover.
7. Remove the wrench.

1. Install the union bolt to the oil control valve filter.
   NOTE: In case of touching the filter, avoid holding the mesh part and holding the frame part.
   Fig 11: Installing Union Bolt To Oil Control Valve Filter

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the oil pipe with 2 new gasket and the union bolt to the No.3 camshaft bearing cap.
   1. Torque: 55 N.m (550 kgf.cm, 41 ft.lbf) 

1. Install the cylinder head and gasket with the 6 bolts.
   1. Torque: 8.5 N.m (85 kgf.cm, 75 in..lbf) 
2. Using a torx socket (E5), install the 2 stud bolts.
   1. Torque: 8.5 N.m (85 kgf.cm, 75 in..lbf) 
      Fig 12: Installing Stud Bolt Using Torx Socket

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the 2 nuts to the 2 stud bolts.
   1. Torque: 8.5 N.m (85 kgf.cm, 75 in..lbf) 
4. Install the high-tension cords and clamps with the 2 bolts.
   1. Torque: 8.0 N.m (80 kgf.cm, 71 in..lbf) 
5. Using a 5 mm hexagon wrench, install the engine wire protector with the bolt and nut.

Install the engine cover with the 4 nuts.

Fig 13: Installing Engine Cover

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Align the camshaft knock pin with the groove on the pulley, and slide on the timing pulley.
2. Slide the timing pulley on the camshaft, facing the front mark forward.
3. Using SST, install the pulley bolt.
   1. SST 09960-10010 (09962-01000, 09963-01000)
   1. Torque: 81 N.m (810 kgf.cm, 60 ft.lbf) 
   Fig 14: Installing Pulley Bolt

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Using SST, align the dot mark on the camshaft timing pulley with the timing mark of the No. 4 timing belt cover.
   1. SST 09960-10010 (09962-01000, 09963-01000)

Fig 15: Aligning Dot Mark On Camshaft Timing Pulley With Timing Mark Of No. 4 Timing Belt Cover

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT:

When re-using timing belt:

• Check that the matchmark on the timing belt matches the end of the No. 1 timing belt cover.

  If the matchmark does not align, shift the meshing of the timing belt and crankshaft timing pulley until they align.

• Align the matchmarks of the timing belt and camshaft timing pulleys.
  Fig 16: Aligning Matchmarks Of Timing Belt And Camshaft Timing Pulleys

  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Remove any oil or water on the camshaft timing pulley, and keep it clean.
2. Install the timing belt, checking the tension between the crankshaft timing pulley and intake camshaft timing pulley.

Fig 17: Installing Timing Belt

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using a press, slowly press in the push rod using 981 - 9,807 N (100 - 1,000 kgf, 220 - 2,205 lbf) of force.
2. Align the holes of the push rod and housing, pass a 1.5 mm hexagon wrench through the holes to keep the push rod retracted.
   Fig 18: Aligning Holes Of Push Rod And Housing

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Release the press.
4. Install the dust boot onto the tensioner.
   Fig 19: Installing Dust Boot Onto Tensioner

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Temporarily install the tensioner with the 2 bolts.
2. Alternately tighten the 2 bolts.
   1. Torque: 27 N.m (270 kgf.cm, 20 ft.lbf) 
   Fig 20: Tightening Timing Belt Tensioner

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Remove the 1.5 mm hexagon wrench from the tensioner with pliers.

Fig 21: Removing 1.5 Mm Hexagon Wrench From Tensioner With Pliers

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Slowly turn the crankshaft pulley 2 revolutions from TDC to TDC.
   NOTE: Always turn the crankshaft clockwise.
   Fig 22: Turning Crankshaft Pulley 2 Revolutions From TDC To TDC

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Check that each pulley aligns with the timing marks as shown in Fig 23 .

   If the marks do not align, remove the timing belt and reinstall it.

   Fig 23: Checking Alignment Of Pulley

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Using SST, install the pulley bolt.

1. SST 09213-70011, 09330-00021

Fig 24: Installing Pulley Bolt

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Torque: 330 N.m (3,300 kgf.cm, 243 ft.lbf) 

Install the tensioner with the 3 bolts.

1. Torque: 21 N.m (210 kgf.cm, 15 ft.lbf) 

1. Install the gasket on the timing belt cover.
2. Using a 5 mm hexagon wrench, install the timing belt cover with the 3 bolts.
   1. Torque: 8.0 N.m (80 kgf.cm, 71 in..lbf) 

1. Install the gasket on the timing belt cover.
2. Using a 5 mm hexagon wrench, install the timing belt cover with the 4 bolts.
   1. Torque: 8.0 N.m (80 kgf.cm, 71 in..lbf) 
3. Install the oil filler cap.

1. Temporarily install the vane pump to the bracket.
2. Install the plate washer and front bracket with the 3 bolts.
   1. Torque: 58 N.m (590 kgf.cm, 43 ft.lbf) for bolt A 52 N.m (530 kgf.cm, 38 ft.lbf) for bolt B 

Fig 25: Installing Plate Washer And Front Bracket Bolts

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install the absorber with the 2 nuts.

1. Torque: 20 N.m (200 kgf.cm, 14 ft.lbf) 

Check for abnormal noise, shock, slippage, correct shift points and smooth operation.