LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2004 >> RX 330 AWD >> Repair and Diagnosis >> Engine Performance >> Remove, Overhaul & Install >> Engine Control System >> Throttle Body ASSY (3MZ-FE) >> Replacement
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Throttle Body ASSY (3MZ-FE): Replacement

  1. DRAIN ENGINE COOLANT (See  ENGINE COOLANT (3MZ-FE)  ) 
  2. REMOVE V-BANK COVER SUB-ASSY 
    1. Using a socket hexagon wrench 5, remove the 3 nuts.
      Fig 1: Locating V-Bank Cover Sub-Assy Removing Nuts
      G03010606Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the V-bank cover.
  3. REMOVE AIR CLEANER INLET NO.2 
  4. REMOVE AIR CLEANER ASSY ) 
  5. REMOVE INTAKE AIR RESONATOR 
    1. Remove the ventilation hose No. 2.
    2. Remove the fuel vapor feed hose from the 2 hose clamps.
    3. Loosen the air cleaner hose clamp bolt, and then remove the intake air resonator.
      Fig 2: Removing Intake Air Resonator
      G03010607Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE THROTTLE BODY ASSY 
    1. Disconnect the throttle motor connector.
    2. Disconnect the water by-pass hose No. 2.
    3. Disconnect the water by-pass hose No. 3.
      Fig 3: Removing Throttle Body Assy
      G03010608Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. TMC Made
      1. Remove the 4 bolts, and then remove the throttle body.
        Fig 4: Removing Throttle Body (TMC Made)
        G03010609Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. TMMWV Made
      1. Remove the 2 bolts and 2 nuts, and then remove the throttle body.
    6. Remove the gasket from the intake air connector.
      Fig 5: Removing Throttle Body (TMMWV Made)
      G03010610Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. INSTALL THROTTLE BODY ASSY 
    1. Install a new gasket to the intake air connector.
    2. TMC Made
      1. Install the throttle body with the 4 bolts.

        Torque: 11 N.m (112 kgf.cm, 8 ft.lbf) 

    3. TMMWV Made
      1. Install the throttle body with the 2 bolts and 2 nuts.

        Torque: 11 N.m (112 kgf.cm, 8 ft.lbf) 

    4. Connect the water by-pass hose No.3.
    5. Connect the water by-pass hose No.2.
    6. Connect the throttle motor connector.
  8. INSTALL INTAKE AIR RESONATOR 
  9. INSTALL AIR CLEANER ASSY ) 
  10. INSTALL AIR CLEANER INLET NO.2 ) 
  11. CHECK CONNECTION OF VACUUM HOSE (See  REPLACEMENT  ) 
  12. ADD ENGINE COOLANT (See  ENGINE COOLANT (3MZ-FE)  ) 
  13. CHECK FOR ENGINE COOLANT LEAKS (See  ON-VEHICLE INSPECTION  ) 
  14. INSTALL V-BANK COVER SUB-ASSY 
    1. Fit the 2 retainers and install the V-bank cover.
    2. Using a socket hexagon wrench 5, tighten the 3 nuts.

      Torque: 7.9 N.m (81 kgf.cm, 70 in.lbf) 

scientia non olet · About LEMON Manuals