LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2005 >> RX 330 AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 563 (Suspension Control) >> Height Control Compressor >> Installation
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Height Control Compressor: Installation

WARNING: This page is about a different car, the 2007 Lexus RX 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL HEIGHT CONTROL COMPRESSOR ASSEMBLY 
    1. Coat the O-ring with MP grease, install the height control compressor assembly.

      HINT:

      When the height control compressor assembly is replaced with new one, it doesn't require a new O-ring.

  2. INSTALL HEIGHT CONTROL DRYER ASSEMBLY 
    1. Install the height control dryer assembly with a bolt onto the height control compressor assembly.

      Torque: 6.4 N*m (65 kgf*cm, 57 in.*lbf) 

      Fig 1: Identifying Bolt On Height Control Dryer Assembly
      G05269886Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect the height control tube No. 2 to the height control dryer assembly.
      Fig 2: Identifying Height Control Tube
      G05269885Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Lock the clip and holder.

      HINT:

      For the installation procedure of the (type 3) tube, refer to PRECAUTION  .

  3. INSTALL REAR HEIGHT CONTROL COMPRESSOR BRACKET 
    1. Install the 3 height control compressor bush No. 2 onto the rear height control compressor bracket.
    2. Install the rear height control compressor bracket with the 3 bolts onto the height control compressor assembly.

      Torque: 5.9 N*m (60 kgf*cm, 52 in.*lbf) 

      Fig 3: Identifying Rear Height Control Compressor Bracket
      G05269890Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Install the 3 clamps.
  4. INSTALL HEIGHT CONTROL FILTER 
    1. Install the 2 hoses and 2 clips to the height control filter.
    2. Install a clamp onto the height control filter.
      Fig 4: Identifying Rear Height Control Compressor Bracket With Clamps
      G05269884Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Connect the height control filter onto the rear height control compressor bracket.
  5. INSTALL REAR HEIGHT CONTROL COMPRESSOR BRACKET 
    1. Passing the wire harness sub-assembly between the bracket and compressor, temporarily place the bracket.
      Fig 5: Passing Wire Harness Sub-Assembly Between Bracket & Compressor
      G05269892Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the rear height control compressor bracket with the 3 bolts onto the height control compressor bracket.

      Torque: 19 N*m (194 kgf*cm, 14 ft.*lbf) 

      Fig 6: Identifying Rear Height Control Compressor Bracket With Bolts
      G05269882Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Connect the hose to the cap grommet and clamp it.
      Fig 7: Identifying Hose To Cap Grommet Clamp
      G05269881Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Install the 3 clamps and the 2 connectors.
      Fig 8: Identifying Connectors & Wire Harness Clamps
      G05269880Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. CONNECT HEIGHT CONTROL TUBE NO.2 
    1. Install a new O-ring onto the height control tube No. 2.
    2. Coat the O-ring with MP grease.
    3. Connect the height control tube No. 2 to the 2 way cap.
      4. Fig 9: Identifying Height Control Tube With Clip & Holder
      G05269879Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Lock the tube with a new clip and a new holder.

      HINT:

      For the installation procedure of the (type 3) tube, refer to PRECAUTION  .

  7. INSPECT AIR LEAK 
  8. INSTALL HEIGHT CONTROL COMPRESSOR COVER 
    1. Install the height control compressor cover with the 2 screws, the clip and the bolt.
scientia non olet · About LEMON Manuals