DTC 01-D5 Absence of Registration Unit (EMV); DTC 01-D8 No Response for Connection Check (EMV); DTC 01-D9 Last Mode Error (EMV); DTC 01-DA No Response Against ON / OFF Command (EMV); DTC 01-DB Mode Status Error (EMV); DTC 01-DC Failure in Transmission (EMV); DTC 01-DE Slave Reset (EMV): Description
DIAGNOSTIC TROUBLE CODE CHART
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| 01-D5 *1, *5 | Device that the sub-code shows is (was) disconnected from system when turning engine switch on (ACC) or on (IG) Communication condition with device that code shows cannot be obtained when engine starts | Inspection for device indicated by sub-code (Refer to inspection list for device indicated by sub-code) |
| 01-D8 *2, *5 | Device indicated by the sub-code is (was) disconnected from system after engine start | |
| 01-D9 *1, *5 | Device (for audio visual system) that had functioned before engine stopped is (was) disconnected from system when engine switch is (was) in on (ACC) or on (IG) | |
| 01-DA *5 | No response is identified when changing mode (audio and visual mode change) Detected when sound and image do not change by switch operation | |
| 01-DB *1, *5 | This code detects dual alarm | |
| 01-DC *3, *5 | This code indicates transmission failure to device indicated by sub-code NOTE: This DTC may not be related to malfunction | |
| 01-DE *4, *5 | This code is stored when slave device has been disconnected after engine start |
HINT:
- *1: This code may be recorded depending on the battery condition or engine start voltage even if no failure is detected.
- *2: If the power connector is disconnected after the engine starts, this code is recorded after 180 seconds.
- *3: This code may be stored if the engine is started, idled for 60 seconds, turned off, and then started again.
- *4: This code may be stored if the engine is started, turned off, and then started again.
- *5: If the device is reported as not existing during verification, check the power source circuit and AVC-LAN circuit for the device.
- READ OUTPUT DTC (LAN MONITOR)
- Read the communication diagnostic check result (see DTC CHECK / CLEAR
).
Result
PROBLEM SYMPTOM CHARTDisplay (Sub-code Output) Proceed to Sub-code output A Not output B
B : Go to step 3
A : GO TO NEXT STEP
- Read the communication diagnostic check result (see DTC CHECK / CLEAR
).
- CHECK AVC-LAN HARNESS AND POWER SOURCE
HINT:
Potential causes of the problem are listed in order of probability in the "Suspected Areas" column of the table below. The sub-code is always displayed with the DTC if it is registered.
- Check these suspected areas when the sub-code is shown.DEVICE NAME AND SUSPECTED AREAS CHART
Sub-code Address (Device Name) Suspected Areas 178 (Navigation ECU) Navigation ECU power source circuit AVC-LAN circuit between multi-display and navigation ECU Navigation ECU 190 (Radio Receiver Assembly) Radio receiver power source circuit AVC-LAN circuit between multi-display and radio receiver assembly Radio receiver assembly 17D (Telephone Transceiver and Speaker Relay) AVC-LAN circuit between stereo component amplifier and stereo component tuner Telephone transceiver and speaker relay 1C6 (Gateway ECU) AVC-LAN circuit between radio receiver assembly and gateway ECU Gateway ECU 280 (Television Camera ECU) Television camera ECU power source circuit AVC-LAN circuit between multi-display and television camera ECU Television camera ECU 440 (Stereo Component Amplifier) Stereo component amplifier power source circuit AVC-LAN circuit between stereo component amplifier and radio receiver assembly Stereo component amplifier
NG : CHECK AND REPLACE MALFUNCTIONING PART
OK : GO TO NEXT STEP
- Check these suspected areas when the sub-code is shown.
- CLEAR DTC
- Clear DTC (see DTC CHECK / CLEAR ).
NEXT : END