Customize Parameters

CUSTOMIZING FUNCTION WITH INTELLIGENT TESTER

HINT:

The items in the table below can be customized.

NOTE:

When the customer requests a change in a function, first make sure that the function can be customized.
Be sure to make a note of the current setting before customizing.
When troubleshooting a function, first make sure that the function is set to the default setting.

SMART:

SMART CUSTOMIZE PARAMETERS

Display (Item)	Default	Contents	Setting
PARK WAIT TIME (Wait time to permit opening door after locking)	2.5s	Function that sets waiting time to permit opening door after door is locked with entry lock function.	0.5s/1.5s/2.5s / 5.0s
IGNITION AREA (SMART ignition available area)	ALL	Function to choose the available area for electrical key to start E/G and cancel the steering lock.	FRONT/ALL
TRUNK OPEN MODE (Luggage compartment opening operation)	ON	Function to open a luggage compartment when the driver has the electrical key and presses the luggage open button.	ON/OFF

WIRELESS DOOR LOCK:

WIRELESS DOOR LOCK CUSTOMIZE PARAMETERS

Display (Item)	Default	Contents	Setting
ALARM FUNCTION (Panic function)	ON	Function to operate the theft deterrent system by keeping pressing the lock button of the transmitter for 2.5 seconds. If there is a panic button, press the panic button instead of the lock button.	ON / OFF
WIRELS BUZZ VOL	Level 7	Function to adjust the volume of the wireless door lock buzzer.	Level 0 / 1 / 2 / 3 / 4 / 5 / 6 / 7

WARNING:

WARNING WIRELESS DOOR LOCK

Display (Item)	Default	Contents	Setting
KEY LOW-BATT WRN	ON	Function to set a warning function for the time when a key battery becomes weak.	ON/OFF

Entry Unlock Mode Switching Function
1. To change the vehicle to entry unlock mode switching function, make sure the vehicle power is off and simultaneously press and hold the electrical key's LOCK switch and another electrical key switch for 4.5 seconds.
  When the switches are pressed and held for 4.5 seconds, the entry door unlock mode changes in the following order: driver door mode, all door mode.
  
  NOTE: After pressing and holding the switches for 4.5 seconds, wait 4.5 seconds before performing the same procedure again.
  - Driver door unlock mode:
    When the driver door's touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.
  - All door unlock mode:
    When the touch sensor is touched, all doors unlock.
2. The certification ECU receives this signal from the entry door control receiver and changes the smart access system with push-button start to the entry unlock mode.
3. The certification ECU sounds the buzzers of the wireless door lock buzzer and combination meter to inform the user that the mode has been switched.
  
  Fig 1: Identifying Multi-Information Display
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  HINT:
  
  The function only changes the entry unlock mode of the smart access system with push-button start. It does not switch the unlocking of the wireless door lock control.
Electrical Key Cancel
The electrical key cancel operation disables the following functions:
- Entry Ignition
- Entry Unlock/Lock
- Entry Luggage Compartment Open
- Electrical Key Lock-in Prevention
- Warning
- Memory Call
1. The operation procedures are as follows:
  Precondition:
  
  Engine switch off, driver side door closed and unlocked.
  1. Unlock the driver side door once with the UNLOCK switch of the electrical key.
  2. Open the driver door within 5 seconds.
  3. Unlock the driver side door twice with the UNLOCK switch of the electrical key within 5 seconds.
  4. Repeat open → close twice for the driver door within 30 seconds, and open again.
    (Driver door: Open → Close → Open → Close → Open)
  5. Unlock the driver side door twice with the UNLOCK switch of the electrical key within 5 seconds.
  6. Repeat open → close once for the driver door within 30 seconds, and open again.
    (Driver door: Open → Close → Open)
  7. Close the driver door within 5 seconds. When electrical key cancel is activated, the wireless door lock buzzer sounds twice.
    To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.