Data List / Active Test
- READ DATA LIST
HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful as intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the DATA LIST information early in troubleshooting is one way to save diagnostic time.
- Connect the intelligent tester (with CAN VIM) to the DLC3.
When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 or less second intervals until communication between the tester and vehicle starts.
- Turn the engine switch on (IG).
- Enter the following menus: DIAGNOSIS / OBD / MOBD / DATA LIST.
- Read the DATA LIST.
MAIN BODY:
DATA LIST (MAIN BODY)Tester Display Measurement Item/Range Normal Condition Diagnostic Note ACC SW Engine switch on (ACC) / ON or OFF ON: Engine switch on (ACC)
OFF: Engine switch off- IGSW Engine switch on (IG) / ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off- SHIFT P SIG Shift P position signal / ON or OFF ON: Shift position is P
OFF: Shift position is not P- STR UNLOCK SW Steering lock condition / ON or OFF ON: Steering is unlocked (Engine switch on (ACC))
OFF: Steering is locked (Engine switch off)- STOP LIGHT SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released- STSW1 Start switch 1 / ON or OFF ON: Engine switch is pushed
OFF: Engine switch is not pushed- STSW2 Start switch 2 / ON or OFF ON: Engine switch is pushed
OFF: Engine switch is not pushed- N SW/C SW Neutral start switch / ON or OFF ON: Shift position is P or N
OFF: Shift position is neither P nor N- LATCH CIRCUIT Latch circuit / ON or OFF ON: Engine switch on (IG) or engine running
OFF: Engine switch off or on (ACC)- IG1 RELAY MON1 IG1 outer relay monitor / ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off- IG1 RELAY MON2 IG1 inner relay monitor / ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off- IG2 RELAY M0N1 IG2 outer relay monitor / ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off- IG2 RELAY M0N2 IG2 inner relay monitor / ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off- ST REQUEST SIG Starter request signal monitor / ON or OFF ON: ST relay is ON
OFF: ST relay is OFFEngine switch pressed and held with shift lever in P or N ACC RELAY MON ACC relay monitor / ON or OFF ON: Engine switch on (ACC)
OFF: Engine switch off- ACC CUT SIG ACC relay cut signal / ON or OFF ON: Engine is cranking
OFF: Engine is not cranking- E/G COND Engine condition / STOP or RUN STOP: Engine is stopped
RUN: Engine is running- VEHICLE SPD SIG Vehicle speed signal / STOP or RUN STOP: Vehicle is stopped
RUN: Vehicle is running- PWR COND Power supply condition / ALL, ACC ON, IG1 IG2, ST ON ALL: All relays are OFF
ACC ON: ACC relay is ON
IG1: IG1 relay is ON
IG2: IG2 relay is ON
ST ON: ST request signal is ON- COM ENTRY&STRT Communication for certification ECU / OK or STOP OK: Communication
STOP: No communication-
- Connect the intelligent tester (with CAN VIM) to the DLC3.
- PERFORM ACTIVE TEST
HINT:
Performing the intelligent tester's ACTIVE TEST allows the relay, VSV, actuator and other items to be operated without removing any parts. Performing the ACTIVE TEST early in troubleshooting is one way to save time. The DATA LIST can be displayed during the ACTIVE TEST.
- Connect the intelligent tester to the DLC3.
- Turn the engine switch on (IG).
- Enter the following menus: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST.
- Perform the ACTIVE TEST according to the display on the tester.
MAIN BODY:
ACTIVE TEST DETAIL (MAIN BODY)Tester Display Test Part Control Range Diagnostic Note LIGHTING IND Indicator for lighting ON / OFF - IND CONDITION Engine switch indicator Green / Amber / No Sig - STR LOCK PWR Power supply for steering lock ECU ON / OFF -