Data List / Active Test
- DATA LIST
HINT:
According to the DATA LIST displayed on the intelligent tester, the value and status of the switch, sensor, actuator, etc. can be obtained without part removal. Reading the DATA LIST as the first step in troubleshooting is one way to shorten labor time.
- Connect the intelligent tester to the DLC3.
- Turn the engine switch on (IG).
- From the display on the tester, read the "DATA LIST".
DATA LIST REFERENCETester Display Measurement Item/Range Normal Condition Diagnostic Note VEHICLE SPD Vehicle speed reading/ min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) Actual vehicle speed Speed indicated on speedometer IG VOLTAGE ECU power supply voltage/ min.: 0 V, max.: 25.5 V Actual ECU power supply voltage: 10 to 14 V - STEERING ANGLE Steering angle sensor reading/ min.: -73725.75 deg, max.: 73728 deg Actual steering angle
Left turn: Reading increases
Right turn: Reading decreasesZero point is set when the battery is connected ENGINE SPD Cam position sensor reading/ min.: 0 rpm, max.: 25,500 rpm Actual engine speed Speed indicated on the combination meter STOP LIGHT SW Stop light switch/ ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released- DAMPER SW 1 Damping force switch 1/ ON or OFF The same as absorber control switch position Operate the absorber control switch TS TS terminal/ ON or OFF ON: During test mode
OFF: Normal mode- TC TC terminal/ ON or OFF ON: DTC recorded
OFF: No DTC recorded- G (UP & DOWN) FR G (up & down) FR sensor reading/ min.: -1045267.3 mm/s2 , max.: 1045299.2 mm/s2 -8,820 mm/s2 to 980 mm/s2 at still condition Reading changes when vehicle (FR) is bounced G (UP & DOWN) FL G (up & down) FL sensor reading/ min.: -1045267.3 mm/s2 , max.: 1045299.2 mm/s2 -8,820 mm/s2 to 980 mm/s2 at still condition Reading changes when vehicle (FL) is bounced G (UP & DOWN) R G (up & down) rear sensor reading/ min.: -1045267.3 mm/s2 , max.: 1045299.2 mm/s2 -8,820 mm/s2 to 980 mm/s2 at still condition Reading changes when vehicle (rear) is bounced DAMPER FR Damper step FR/ min.: 0 step, max.: 255 step Min.: 1 step, max.: 17 step - DAMPER FL Damper step FL/ min.: 0 step, max.: 255 step Min.: 1 step, max.: 17 step - DAMPER RR Damper step RR/ min.: 0 step, max.: 255 step Min.: 1 step, max.: 17 step - DAMPER RL Damper step RL/ min.: 0 step, max.: 255 step Min.: 1 step, max.: 17 step - WHEEL SPD FR Front right wheel speed reading/ min.: 0 km/h (0 mph), max.: 255 km/h(158 mph) Actual vehicle speed Speed indicated on speedometer MAX DMP STEP FR Max. damper step FR/ min.: 0 step, max.: 255 step 17 step at still condition - MAX DMP STEP FL Max. damper step FL/ min.: 0 step, max.: 255 step 17 step at still condition - MAX DMP STEP RR Max. damper step RR/ min.: 0 step, max.: 255 step 17 step at still condition - MAX DMP STEP RL Max. damper step RL/ min.: 0 step, max.: 255 step 17 step at still condition - #CODES Number of DTC recorded/min.: 0, max.: 255 Min.: 0, Max.: XX - - ACTIVE TEST
HINT:
Performing the ACTIVE TEST using the intelligent tester allows the relay, actuator, etc. to operate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one way to shorten labor time. It is possible to display the DATA LIST during the ACTIVE TEST.
- Connect the intelligent tester to DLC3.
- Turn the engine switch on (IG).
- According to the display on the tester, perform the "ACTIVE TEST".
ACTIVE TEST REFERENCETester Display Test Part Control Range DAMPER FR Damper step front right wheel 1 step to 17 steps (Damper step is change) DAMPER FL Damper step front left wheel 1 step to 17 steps (Damper step is change) DAMPER RR Damper step rear right wheel 1 step to 17 steps (Damper step is change) DAMPER RL Damper step rear left wheel 1 step to 17 steps (Damper step is change)