LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2007 >> GS 430 >> Repair and Diagnosis >> Transmission >> Automatic Trans >> Automatic Transaxle >> Transmission Wire >> Installation
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Transmission Wire: Installation

  1. INSTALL TRANSMISSION WIRE 
    1. Coat a new O-ring with ATF and install it to the transmission wire.
      Fig 1: Identifying Transmission Wire O-Ring
      G05289668Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the transmission wire with the bolt.

      Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

    3. Connect the transmission wire connector.
  2. CONNECT TRANSMISSION WIRE 
    1. Coat an O-ring of the ATF temperature sensor with ATF.
      Fig 2: Locating Transmission Wire Bolt
      G05295334Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect the 9 connectors to the solenoid valves.
      Fig 3: Locating Solenoid Valves Connectors
      G05289666Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Install the 2 clamps with the 2 bolts.

      Torque: Bolt A 

      6.4 N*m (65 kgf*cm, 57 in.*lbf) 

      Bolt B 

      10 N*m (102 kgf*cm, 7 ft.*lbf) 

      Fig 4: Locating Clamp Bolts
      G05289673Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Install the ATF temperature sensor and lock plate with the bolt.

      Torque: 10 N*m (100 kgf*cm, 7 ft.*lbf) 

  3. INSTALL VALVE BODY OIL STRAINER ASSEMBLY 
    1. Coat a new O-ring with ATF.
      Fig 5: Locating Lock Plate Bolt
      G05289664Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the O-ring.
      Fig 6: Identifying Oil Strainer O-Ring
      G05295330Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Install the oil strainer with the 4 bolts.

      Torque: 10 N*m (100 kgf*cm, 7 ft.*lbf) 

    Fig 7: Locating Oil Strainer Bolts
    G05295329Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY 
    1. Install the 3 magnets in the oil can.
      Fig 8: Identifying Magnets
      G05295344Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install a new gasket and the oil pan to the transmission case with the 20 bolts.

      Torque: 4.4 N*m (45 kgf*cm, 39 in.*lbf) 

    Fig 9: Locating Oil Pan Bolts
    G05294751Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. INSTALL ENGINE UNDER COVER AIR GUIDE BRACKET 
    1. Install the engine under cover air guide bracket with the 2 bolts.
      Fig 10: Locating Engine Under Cover Air Guide Bracket Bolts
      G05295326Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 26 N*m (260 kgf*cm, 19 ft.*lbf) 

  6. INSTALL EXHAUST PIPE NO.1 SUPPORT BRACKET SUB-ASSEMBLY (See  TORQUE CONVERTER AND DRIVE PLATE  ) 
  7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
  8. ADD AUTOMATIC TRANSMISSION FLUID 

    (See AUTOMATIC TRANSMISSION FLUID )

  9. INSTALL ENGINE UNDER COVER NO.2 
  10. RESET MEMORY 

    (See MANUAL SHIFTING TEST )

  11. PERFORM INITIALIZATION 

    (See INITIALIZATION )