Data List / Active Test
- READ DATA LIST
HINT:
Using the intelligent tester's DATA LIST allows switch, sensor, actuator and other item values to be read without out removing any parts. Reading the DATA LIST early in troubleshooting is one way to save time.
- Connect the intelligent tester (with CAN VIM) to the DLC3.
- Turn the power switch ON (IG).
- Turn the intelligent tester on.
- Read the DATA LIST according to the display on the tester.
Skid control ECU:
DATA LISTTester Display Measurement Item/Range Normal Condition Diagnostic Note Electronically Controlled Brake System MTR RELAY Electronically controlled brake system motor relay / ON or OFF ON: Motor relay ON
OFF: Motor relay OFF- TRAC / VSC OFF SW Traction OFF switch / ON or OFF ON: Traction OFF switch OFF
OFF: Traction OFF switch ON- IDLE SW Main idle switch / ON or OFF ON: Accelerator pedal released
OFF: Accelerator pedal depressed- STOP LAMP SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released- PARKING BRAKE SW Parking brake switch / ON or OFF ON: Parking brake applied
OFF: Parking brake released- LEVER POSITION Shift lever position information / P/N, R, D/M, 1st-6th/B, FAIL - - FR WHEEL SPD Wheel speed sensor (FR) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer FL WHEEL SPD Wheel speed sensor (FL) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer RR WHEEL SPD Wheel speed sensor (RR) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer RL WHEEL SPD Wheel speed sensor (RL) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer DECELERAT SEN Acceleration sensor 1 reading / min.: -1.869 G, max.: 1.869 G Approximately 0 +-0.13 G while stationary Reading changes when vehicle is bounced DECELERAT SEN 2 Acceleration sensor 2 reading / min.: -1.869 G, max.: 1.869 G Approximately 0 +-0.13 G while stationary Reading changes when vehicle is bounced FR WHEEL DIR Wheel direction (FR) / FORWARD or BACK FORWARD: Forward
BACK: Back- FL WHEEL DIR Wheel direction (FL)/ FORWARD or BACK FORWARD: Forward
BACK: Back- RR WHEEL DIR Wheel direction (RR) / FORWARD or BACK FORWARD: Forward
BACK: Back- RL WHEEL DIR Wheel direction (RL) / FORWARD or BACK FORWARD: Forward
BACK: Back- ACCELERATOR % Percentage of accelerator pedal opening angle / min.: 0%, max.: 128% - - FR SPD OPN FR speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- FL SPD OPN FL speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- RR SPD OPN RR speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- RL SPD OPN RL speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- YAW RATE OPN Yaw rate sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- DECELERAT OPN Acceleration sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- STEERING OPN Steering angle sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- M/C OPN Master cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- HV COM OPN HV communication open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- #DTC Number of DTC / min.: 0, max.: 255 - - ABS WARN LAMP ABS warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- BRAKE WARN LAMP BRAKE warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- SLIP INDI LAMP SLIP indicator light / ON or OFF ON: Indicator light ON
OFF: Indicator light OFF- BUZZER Skid control buzzer / ON or OFF ON: Buzzer ON
OFF: Buzzer OFF- VSC WARN LAMP Brake control warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- VEHICLE SPD Maximum wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Actual vehicle speed Speed indicated on speedometer FR WHEEL ACCEL FR wheel acceleration / min.: -200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2
Max.: 199.27 m/s2- FL WHEEL ACCEL FL wheel acceleration / min.: -200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2
Max.: 199.27 m/s2- RR WHEEL ACCEL RR wheel acceleration / min.: -200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2
Max.: 199.27 m/s2- RL WHEEL ACCEL RL wheel acceleration / min.: -200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2
Max.: 199.27 m/s2- ZERO DECELERAT Memorized zero value / min.: -25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2
Max.: 24.91 m/s2- ZERO DECELERAT2 Memorized zero value / min.: -25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2
Max.: 24.91 m/s2- ZERO STEERING Memorized zero value / min.: -3276.8 deg, max.: 3276.7 deg Min.: -3276.8 deg
Max.: 3276.7 deg- LATERAL G Lateral G / min.: -25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2
Max.: 24.91 m/s2- FORWARD&REA G Forward and rearward G / min.: -25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2
Max.: 24.91 m/s2- YAW RATE VALUE Yaw rate value / min.: -128 deg/s, max.: 127 deg/s Min.: -128 deg/s
Max.: 127 deg/s- STEERING ANGLE Steering angle value / min.: -3276.8 deg, max.: 3276.7 deg Min.: -3276.8 deg
Max.: 3276.7 deg- TRAC STATUS TRAC control status / ON or OFF ON: During the control - TRAC BRK STATUS TRAC brake control status / ON or OFF ON: During the control - FR VSC STATUS FR wheel VSC control status / ON or OFF ON: During the control - FL VSC STATUS FL wheel VSC control status / ON or OFF ON: During the control - RR VSC STATUS RR wheel VSC control status / ON or OFF ON: During the control - RL VSC STATUS RL wheel VSC control status / ON or OFF ON: During the control - YAW RATE SENS 1 Yaw rate sensor 1 / min.: -128 deg/s, max.: 127 deg/s Min.: -128 deg/s
Max.: 127 deg/s- YAW RATE SENS 2 Yaw rate sensor 2 / min.: -128 deg/s, max.: 127 deg/s Min.: -128 deg/s
Max.: 127 deg/s- ZERO YAW RATE Memorized zero value / min.: -128 deg/s, max.: 127 deg/s Min.: -128 deg/s
Max.: 127 deg/s- ZERO YAW RATE 2 Memorized zero value / min.: -128 deg/s, max.: 127 deg/s Min.: -128 deg/s
Max.: 127 deg/s- STEERING SEN Steering angle sensor / min.: -3276.8 deg, max.: 3276.7 deg Left turn: Increase
Right turn: Decrease- MAS CYL PRESS 1 Master cylinder pressure sensor 1 reading / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V Reading increases when brake pedal is depressed MAS CYL PRESS 2 Master cylinder pressure sensor 2 reading / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V Reading increases when brake pedal is depressed FR ABS STATUS FR wheel ABS control status / ON or OFF ON: During the control - FL ABS STATUS FL wheel ABS control status / ON or OFF ON: During the control - RR ABS STATUS RR wheel ABS control status / ON or OFF ON: During the control - RL ABS STATUS RL wheel ABS control status / ON or OFF ON: During the control - BA STATUS BA control status / ON or OFF ON: During the control - PBA STATUS PBA control status / ON or OFF ON: During the control - PEDAL STROKE Stroke sensor / min.: 0 V, max.: 5 V When brake pedal is released: 0.7 to 1.3 V - PEDAL STROKE 2 Stroke sensor 2 / min.: 0 V, max.: 5 V When brake pedal is released: 3.7 to 4.3 V - ACC PRESS SENS Accumulator pressure sensor / min.: 0 V, max.: 5 V Specified value: 3.2 to 4.0 V - FR W/C SENS FR wheel cylinder pressure sensor / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V - FL W/C SENS FL wheel cylinder pressure sensor/ min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V - RR W/C SENS RR wheel cylinder pressure sensor / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V - RL W/C SENS RL wheel cylinder pressure sensor / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V - RESERVOIR SW Brake fluid level warning switch / ON or OFF ON: Reservoir level normal
OFF: Reservoir level low- Electronically Controlled Brake System WARN LAMP Brake control warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- Electronically Controlled Brake System MTR RELAY 2 Electronically controlled brake system motor relay 2 / ON or OFF ON: Motor relay ON
OFF: Motor relay OFF- Electronically Controlled Brake System RELAY Electronically controlled brake system main relay / ON or OFF ON: Main relay ON
OFF: Main relay OFF- Electronically Controlled Brake System RELAY 2 Electronically controlled brake system main relay 2 / ON or OFF ON: Main relay ON
OFF: Main relay OFF- VOLT M/C SEN Voltage of master cylinder pressure sensor / min.: -2.5 V, max.: 2.49 V When brake pedal is released: 0.3 to 0.9 V - VOLT M/C SEN 2 Voltage of master cylinder pressure sensor 2 / min.: -2.5 V, max.: 2.49 V When brake pedal is released: 0.3 to 0.9 V - VOLT STROK SEN Voltage of stroke sensor / min.: -2.5 V, max.: 2.49 V When brake pedal is released: 0.7 to 1.3 V - VOLT STROK SEN 2 Voltage of stroke sensor 2 / min.: -2.5 V, max.: 2.49 V When brake pedal is released: 3.7 to 4.3 V - SLAFR CUR SLAFR solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLAFL CUR SLAFL solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLARR CUR SLARR solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLARL CUR SLARL solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLRFR CUR SLRFR solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLRFL CUR SLRFL solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLRRR CUR SLRRR solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLRRL CUR SLRRL solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - M/C2 OPN Master cylinder pressure sensor 2 open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- STROKE OPN Stroke sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- FR W/C OPN FR wheel cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- FL W/C OPN FL wheel cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- RR W/C OPN RR wheel cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- RL W/C OPN RL wheel cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- ACC OPN Accumulator pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- SMC1 Electronically controlled brake system solenoid (SMC1) / ON or OFF ON: Operate
OFF: Not operate- SMC2 Electronically controlled brake system solenoid (SMC2) / ON or OFF ON: Operate
OFF: Not operate- SCSS Electronically controlled brake system solenoid (SCSS) / ON or OFF ON: Operate
OFF: Not operate- RR RQST TORQ Rear regenerative request torque / min.: 0 N*m, max.: 65,536 N*m - - RR OPERATE TORQ Rear regenerative operation torque / min.: 0 N*m, max.: 65,536 N*m - - REGEN COOP Regenerative cooperation / ON or OFF ON: Operate
OFF: Not operate-
- PERFORM ACTIVE TEST
HINT:
Performing the intelligent tester's ACTIVE TEST allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the ACTIVE TEST early in troubleshooting is one way to save time. The DATA LIST can be displayed during the ACTIVE TEST.
- Connect the intelligent tester (with CAN VIM) to the DLC3.
- Turn the power switch ON (IG).
- Turn the intelligent tester on.
- Perform the ACTIVE TEST according to the display on the tester.
HINT:
- The power switch must be turned ON (IG) to proceed to the ACTIVE TEST using the intelligent tester.
- The ACTIVE TESTs of the ABS solenoid, ABS motor relay, ABS warning light and brake warning light are available when the vehicle is stopped.
- The motors stop automatically after 5 seconds of activation to prevent them from being damaged. When the motors are driven repeatedly, certain intervals are required.
- Each solenoid stops automatically after 2 seconds of activation to prevent them from being damaged, and can be operated again after a certain interval.
- Do not depress the brake pedal while only the pressure reduction solenoid valves are on.
- Do not drive 2 or more solenoids simultaneously except to operate the pressure holding solenoid valves and pressure reduction solenoid valves of each wheel.
Skid control ECU:
DATA LISTTester Display Test Part Control Range SMC1 Turns electronically controlled brake system solenoid (SMC1) ON / OFF Operation sound of solenoid (clicking sound) can be heard SMC2 Turns electronically controlled brake system solenoid (SMC2) ON / OFF Operation sound of solenoid (clicking sound) can be heard Electronically Controlled Brake System RELAY Turns electronically controlled brake system main relay ON / OFF Operation sound of relay (clicking sound) can be heard Electronically Controlled Brake System RELAY 2 Turns electronically controlled brake system main relay 2 ON / OFF Operation sound of relay (clicking sound) can be heard ABS WARN LAMP Turns ABS warning light ON / OFF Observe combination meter VSC WARN LAMP Turns brake control warning light ON / OFF Observe combination meter SLIP INDI LAMP Turns SLIP indicator light ON / OFF Observe combination meter BRAKE WARN LAMP Turns BRAKE warning light ON / OFF Observe combination meter BUZZER Turns skid control buzzer ON / OFF Buzzer can be heard STP LAMP RELAY Turns stop light operation relay ON / OFF Observe rear combination light (stop light) (Does not come on for 5 sec. or more) Electronically Controlled Brake System WARN LAMP Turns brake control warning light ON / OFF Observe combination meter Electronically Controlled Brake System MTR RELAY Turns electronically controlled brake system motor relay ON / OFF Operation sound of relay (clicking sound) and motor can be heard Electronically Controlled Brake System MTR RELAY 2 Turns electronically controlled brake system motor relay 2 ON / OFF Operation sound of relay (clicking sound) and motor can be heard Electronically Controlled Brake System INVALID Electronically controlled brake system control invalid ON / OFF Electronically controlled brake system control is blocked (braking with no boost assist) ZERO DOWN Accumulator zero down activation ON / OFF Brake fluid existing the accumulator makes noise SCSS PATTERN Stroke simulator cut valve pattern activation ON / OFF -
(Difficult to identify visually)ACT PATTERN Actuator air bleeding pattern activation ON / OFF When accumulator pressure lowers, pump operation creates sound POWER SUPPLY1 Power supply air bleeding pattern activation 1 ON / OFF When accumulator pressure lowers, pump operation creates sound POWER SUPPLY2 Power supply air bleeding pattern activation 2 ON / OFF When accumulator pressure lowers, pump operation creates sound RL AIR BLEEDING RL wheel air bleeding pattern activation ON / OFF When accumulator pressure lowers, pump operation creates sound RR AIR BLEEDING RR wheel air bleeding pattern activation ON / OFF When accumulator pressure lowers, pump operation creates sound PUMP PATTERN Pump check pattern activation ON / OFF When accumulator pressure lowers, pump operation creates sound DRAIN PATTERN Drain system air bleeding pattern activation ON / OFF When accumulator pressure lowers, pump operation creates sound SLRRL CLOSE Turns SLRRL solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard SLARL CLOSE Turns SLARL solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard SLRRR CLOSE Turns SLRRR solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard SLARR CLOSE Turns SLARR solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard SLRFL CLOSE Turns SLRFL solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard SLAFL CLOSE Turns SLAFL solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard SLRFR CLOSE Turns SLRFR solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard SLAFR CLOSE Turns SLAFR solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard