LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2007 >> LS 460 >> Repair and Diagnosis >> Body & Frame >> Mirrors >> Mirror >> Power Mirror Control System >> Data List / Active Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test

  1. READ DATA LIST 

    HINT:

    Using the intelligent tester or Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
    1. Warm up the engine.
    2. Turn the engine switch off.
    3. Connect the intelligent tester (with CAN VIM) or Techstream to the DLC3.
    4. Turn the engine switch on (IG).
    5. Turn the tester on.
    6. Enter the following menus:
      1. Intelligent tester - Select: DIAGNOSIS / OBD / MOBD / (desired system) / DATA LIST / ALL /
      2. Techstream - Select: Body Electrical / (desired system) / Data List /
    7. According to the display on tester, read the "DATA LIST".
      1. Intelligent tester

        D-DOOR 

        INTELLIGENT TESTER - D-DOOR

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        MIRROR MEM 1 Driver side mirror position memorized in seat memory switch M1 /ON or OFF ON: Memorized
        OFF: Not memorized        		 -
        MIRROR MEM 2 Driver side mirror position memorized in seat memory switch M2 / ON or OFF ON: Memorized
        OFF: Not memorized        		 -
        MIRROR MEM 3 Driver side mirror position memorized in seat memory switch M3 / ON or OFF ON: Memorized
        OFF: Not memorized        		 -
        V POS MR S VOL Driver side mirror vertical sensor voltage / MIN: 0, MAX: 255 Within range from 0 to 255 -
        H POS MR S VOL Driver side mirror horizontal sensor voltage / MIN: 0, MAX: 255 Within range from 0 to 255 -

        P-DOOR 

        INTELLIGENT TESTER - P-DOOR

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        MIRROR MEM 1 Passenger side mirror position memorized in seat memory switch M1 / ON or OFF ON: Memorized
        OFF: Not memorized        		 -
        MIRROR MEM 2 Passenger side mirror position memorized in seat memory switch M2 / ON or OFF ON: Memorized
        OFF: Not memorized        		 -
        MIRROR MEM 3 Passenger side mirror position memorized in seat memory switch M3 / ON or OFF ON: Memorized
        OFF: Not memorized        		 -
        V POS MR S VOL Passenger side mirror vertical sensor voltage / MIN: 0, MAX: 255 Within range from 0 to 255 -
        H POS MR S VOL Passenger side mirror horizontal sensor voltage / MIN: 0, MAX: 255 Within range from 0 to 255 -

        D-SEAT SW 

        INTELLIGENT TESTER - D-SEAT SW

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        MIRR SEL SW R Mirror master switch signal for RH mirror / ON or OFF ON: Switch is in R position
        OFF: Switch is OFF or in L position        		 -
        MIRR SEL SW L Mirror master switch signal for LH mirror / ON or OFF ON: Switch is in L position
        OFF: Switch is OFF or in R position        		 -
        MIR - ADJ RIGHT Mirror control switch signal (RIGHT) / ON or OFF ON: RIGHT switch is ON
        OFF: Any switch except RIGHT is ON or all switches are OFF        		 -
        MIR - ADJ LEFT Mirror control switch signal (LEFT) / ON or OFF ON: LEFT switch is ON
        OFF: Any switch except LEFT is ON or all switches are OFF        		 -
        MIR-ADJ UP Mirror control switch signal (UP) / ON or OFF ON: UP switch is ON
        OFF: Any switch except UP is ON or all switches are OFF        		 -
        MIR - ADJ DOWN Mirror control switch signal (DOWN) / ON or OFF ON: DOWN switch is ON
        OFF: Any switch except DOWN is ON or all switches are OFF        		 -
        MIRROR CLOSE Mirror retract switch signal / ON or OFF ON: Switch is ON (retracting)
        OFF: Switch is OFF        		 -
        MIRROR OPEN Mirror retract switch signal / ON or OFF ON: Switch is ON (returning)
        OFF: Switch is OFF        		 -
      2. Techstream

        Driver Door 

        TECHSTREAM - DRIVER DOOR

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        Mirror Memory No. 1 Driver side mirror position memorized in seat memory switch M1 /ON or OFF ON: Memorized
        OFF: Not memorized        		 -
        Mirror Memory No.2 Driver side mirror position memorized in seat memory switch M2 / ON or OFF ON: Memorized
        OFF: Not memorized        		 -
        Mirror Memory No.3 Driver side mirror position memorized in seat memory switch M3 / ON or OFF ON: Memorized
        OFF: Not memorized        		 -
        Mirror Vertical Sensor Voltage Driver side mirror vertical sensor voltage / MIN: 0, MAX: 255 Within range from 0 to 255 -
        Mirror Horizontal Sensor Voltage Driver side mirror horizontal sensor voltage / MIN: 0, MAX: 255 Within range from 0 to 255 -

        Passenger Door 

        TECHSTREAM - PASSENGER DOOR

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        Mirror Memory No.1 Passenger side mirror position memorized in seat memory switch M1 / ON or OFF ON: Memorized
        OFF: Not memorized        		 -
        Mirror Memory No.2 Passenger side mirror position memorized in seat memory switch M2 / ON or OFF ON: Memorized
        OFF: Not memorized        		 -
        Mirror Memory No.3 Passenger side mirror position memorized in seat memory switch M3 / ON or OFF ON: Memorized
        OFF: Not memorized        		 -
        Mirror Vertical Sensor Voltage Passenger side mirror vertical sensor voltage / MIN: 0, MAX: 255 Within range from 0 to 255 -
        Mirror Horizontal Sensor Voltage Passenger side mirror horizontal sensor voltage / MIN: 0, MAX: 255 Within range from 0 to 255 -

        D-SEAT SW 

        TECHSTREAM - D-SEAT SW

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        Mirror Selection SW (Right) Mirror master switch signal for RH mirror 1 ON or OFF ON: Switch is in R position
        OFF: Switch is OFF or in L position        		 -
        Mirror Selection SW (Left) Mirror master switch signal for LH mirror / ON or OFF ON: Switch is in L position
        OFF: Switch is OFF or in R position        		 -
        Mirror Adjustment Right Mirror control switch signal (RIGHT) / ON or OFF ON: RIGHT switch is ON
        OFF: Any switch except RIGHT is ON or all switches are OFF        		 -
        Mirror Adjustment Left Mirror control switch signal (LEFT) / ON or OFF ON: LEFT switch is ON
        OFF: Any switch except LEFT is ON or all switches are OFF        		 -
        Mirror Adjustment Up Mirror control switch signal (UP) / ON or OFF ON: UP switch is ON
        OFF: Any switch except UP is ON or all switches are OFF        		 -
        Mirror Adjustment Down Mirror control switch signal (DOWN) / ON or OFF ON: DOWN switch is ON
        OFF: Any switch except DOWN is ON or all switches are OFF        		 -
        Mirror Close Switch Mirror retract switch signal / ON or OFF ON: Switch is ON (retracting)
        OFF: Switch is OFF        		 -
        Mirror Open Switch Mirror retract switch signal / ON or OFF ON: Switch is ON (returning)
        OFF: Switch is OFF        		 -
  2. PERFORM ACTIVE TEST 

    HINT:

    Using the intelligent tester or Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Warm up the engine.
    2. Turn the engine switch off.
    3. Connect the intelligent tester (with CAN VIM) or the Techstream to the DLC3.
    4. Turn the engine switch on (IG).
    5. Turn the tester on.
    6. Enter the following menus:
      1. Intelligent tester - Select: DIAGNOSIS / OBD / MOBD / (desired system) / ACTIVE TEST /
      2. Techstream - Select: Body Electrical / (desired system) / Active Test /
    7. According to the display on tester, perform the "ACTIVE TEST".
      1. Intelligent tester

        D-DOOR 

        INTELLIGENT TESTER - D-DOOR

        Tester Display Test Part Control Range
        MIRR HEATER Mirror heater operation OFF / ON
        MIRR FOLD / RETRN Mirror retract operation FOLD/RETURN
        MIRR RIGHT/LEFT Mirror horizontal operation RIGHT / LEFT
        MIRR UP / DOWN Mirror vertical operation UP/DOWN

        P-DOOR 

        INTELLIGENT TESTER - P-DOOR

        Tester Display Test Part Control Range
        MIRR HEATER Mirror heater operation OFF/ON
        MIRR FOLD / RETRN Mirror retract operation FOLD/RETURN
        MIRR RIGHT / LEFT Mirror horizontal operation RIGHT/LEFT
        MIRR UP / DOWN Mirror vertical operation UP/DOWN
      2. Techstream

        Driver Door 

        TECHSTREAM - DRIVER DOOR

        Tester Display Test Part Control Range
        Mirror Heater Mirror heater operation OFF/ON
        Mirror Fold / Return Mirror retract operation FOLD/RETURN
        Mirror Right / Left Mirror horizontal operation RIGHT / LEFT
        Mirror Up / Down Mirror vertical operation UP/DOWN

        Passenger Door 

        TECHSTREAM - PASSENGER DOOR

        Tester Display Test Part Control Range
        Mirror Heater Mirror heater operation OFF/ON
        Mirror Fold / Return Mirror retract operation FOLD/RETURN
        Mirror Right / Left Mirror horizontal operation RIGHT / LEFT
        Mirror Up / Down Mirror vertical operation UP/DOWN
scientia non olet · About LEMON Manuals