LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2007 >> LS 460 >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System - Service Information & Circuit Tests >> Air Fuel Ratio Sensor >> Installation
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Air Fuel Ratio Sensor: Installation

  1. INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1) 
    1. Using SST, remove the air fuel ratio sensor from the exhaust manifold LH.

      SST 09224-00010 

      Torque: 

      without SST 

      44 N*m (449 kgf*cm, 32 ft.*lbf) 

      with SST 

      40 N*m (408 kgf*cm, 30 ft.*lbf) 

      NOTE: Use a torque wrench with a fulcrum length of 300 mm (11.81 in.)
      Fig 1: Installing Air Fuel Ratio Sensor (For Bank 1 Sensor 1)
      G04943112Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1) 
    1. Using SST, remove the air fuel ratio sensor from the exhaust manifold RH.

      SST 09224-00010 

      Torque: 

      without SST 

      44 N*m (449 kgf*cm, 32 ft.*lbf) 

      with SST 

      40 N*m (408 kgf*cm, 30 ft.*lbf) 

      NOTE: Use a torque wrench with a fulcrum length of 300 mm (11.81 in.)
      Fig 2: Installing Air Fuel Ratio Sensor (For Bank 2 Sensor 1)
      G04943113Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH  (See INSTALLATION )
  4. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR  (See INSTALLATION )
  5. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH  (See INSTALLATION )
  6. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR  (See INSTALLATION )
  7. INSTALL OIL DIPSTICK GUIDE  (See INSTALLATION )
  8. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH  (See INSTALLATION )
  9. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH  (See INSTALLATION )
  10. INSTALL ENGINE UNDER COVER SUB-ASSEMBLY LH  (See INSTALLATION )
  11. INSTALL ENGINE UNDER COVER SUB-ASSEMBLY RH  (See INSTALLATION )
  12. INSTALL FRONT STABILIZER BAR  (See INSTALLATION )
  13. INSTALL ENGINE UNDER COVER REAR LH  (See INSTALLATION )
  14. INSTALL ENGINE UNDER COVER REAR RH  (See INSTALLATION )
  15. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (w/ VGRS)  (See INSTALLATION )
  16. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (w/o VGRS)  (See INSTALLATION )
  17. INSTALL STEERING INTERMEDIATE SHAFT (w/o VGRS)  (See INSTALLATION )
  18. INSTALL STEERING SLIDING YOKE WITH SHAFT SUB-ASSEMBLY (w/ VGRS)  (See INSTALLATION )
  19. INSTALL STEERING SLIDING YOKE WITH SHAFT SUB-ASSEMBLY (w/o VGRS)  (See INSTALLATION )
  20. INSTALL FRONT EXHAUST PIPE ASSEMBLY 
    1. Install the front exhaust pipe (see INSTALLATION ).
  21. INSTALL GENERATOR ASSEMBLY  (See INSTALLATION )
  22. INSTALL V-RIBBED BELT  (See INSTALLATION )
  23. INSTALL INTAKE AIR CONNECTOR PIPE (See  INSTALLATION   ) 
  24. INSTALL NO. 2 ENGINE UNDER COVER  (See INSTALLATION )
  25. INSTALL FRONT SUSPENSION MEMBER PROTECTOR LOWER  (See INSTALLATION )
  26. INSTALL NO. 1 ENGINE UNDER COVER  (See REPLACEMENT )
  27. INSTALL NO. 1 AIR CLEANER INLET (See  INSTALLATION   ) 
  28. INSTALL AIR CLEANER INLET COVER (See  INSTALLATION   ) 
  29. INSTALL V-BANK COVER SUB-ASSEMBLY (See  INSTALLATION   ) 
  30. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
  31. INSTALL COWL TOP VENTILATOR LOUVER RH  (See INSTALLATION )
  32. PERFORM INITIALIZATION 
    1. Perform initialization (see INITIALIZATION ).
      NOTE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.
scientia non olet · About LEMON Manuals