Reference Value From Consult-II
WARNING: This page is about a different car, the 2007 Nissan Maxima. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION:
The display shows the control unit calculation data, so a normal value might be displayed even in the event the output circuit (harness) is open or short circuited.
REFERENCE VALUE FROM CONSULT-II
| Monitor item | Display content | Data monitor |
NOTE:
Error inspection checklist
|
|
|---|---|---|---|---|
| Condition | Reference value in normal operation | |||
| FR RH SENSOR FR LH SENSOR RR RH SENSOR RR LH SENSOR |
Wheel speed | Vehicle stopped | 0 [km/h (MPH)] | "Wheel Sensor System Inspection " |
| Vehicle running (Note 1) | Almost in accordance with speedometer display (within ±10%) | |||
| ACCEL POS SIG | Open/close condition of throttle valve (linked with accelerator pedal). | Accelerator pedal not depressed (ignition switch is ON) | 0% | "CAN COMMUNICATION SYSTEM INSPECTION " |
| Depress accelerator pedal (ignition switch is ON) | 0 to 100% | |||
| ENGINE SPEED | With engine running | With engine stopped | 0 rpm | "ENGINE SYSTEM INSPECTION " |
| Engine running | Almost in accordance with tachometer display | |||
| BATTERY VOLT | Battery voltage supplied to ABS actuator and electric unit (control unit) | Ignition switch ON | 10 to 16V | "ABS/TCS CONTROL UNIT POWER AND GROUND SYSTEMS INSPECTION " |
| STOP LAMP SW | Brake pedal operation | Brake pedal depressed | ON | "STOP LAMP SWITCH SYSTEM INSPECTION " |
| Brake pedal not depressed | OFF | |||
| ABS WARN LAMP | ABS warning lamp ON condition (Note 2) | ABS warning lamp ON | ON | "ABS WARNING LAMP DOES NOT COME ON WHEN IGNITION SWITCH IS TURNED ON " |
| ABS warning lamp OFF | OFF | |||
| MOTOR RELAY | Operation status of motor and motor relay | Ignition switch ON or engine running (ABS not operated) | OFF | "ACTUATOR MOTOR, MOTOR RELAY, AND CIRCUIT INSPECTION " |
| Ignition switch ON or engine running (ABS operated) | ON | |||
| ACTUATOR RLY | Actuator relay operation status | Vehicle stopped (Ignition switch ON) | OFF | "ACTUATOR MOTOR, MOTOR RELAY, AND CIRCUIT INSPECTION " |
| Vehicle stopped (Engine running) | ON | |||
| SLIP LAMP | SLIP indicator lamp status (Note 4) | When SLIP indicator lamp is ON | ON | "ARRANGEMENT OF COMBINATION METER " |
| When SLIP indicator lamp is OFF | OFF | |||
| FR LH IN SOL FR LH OUT SOL FR RH IN SOL FR RH OUT SOL RR RH IN SOL RR RH OUT SOL RR LH IN SOL RR LH OUT SOL |
Solenoid valve operation | Actuator (solenoid) is active ("ACTIVE TEST" with CONSULT-II) or actuator relay is inactive (in fail-safe mode). | ON | - |
| When actuator (solenoid) is not active and actuator relay is active (ignition switch ON). | OFF | |||
| TCS FAIL SIG ABS FAIL SIG EBD FAIL SIG |
Fail signal status | TCS fail ABS fail EBD fail |
OFF | TCS system ABS system EBD system |
| Note 1: Confirm tire pressure is normal. | ||||
| Note 2: ON/OFF timing of ABS warning lamp | ||||
| ON: For approximately 2 seconds after ignition switch is turned ON, or when a malfunction is detected. | ||||
| OFF: Approximately 2 seconds after ignition switch is turned ON (when system is in normal operation) and TCS function is not activated. | ||||
| Note 4: SLIP indicator lamp ON/OFF timing | ||||
| ON: For approximately 2 seconds after ignition switch is turned ON, or when a malfunction is detected and TCS function is activated while driving. | ||||
| OFF: Approximately 2 seconds after ignition switch is turned ON (when system is in normal operation) and TCS function is not activated. | ||||
| Flashing: TCS function is active during driving | ||||