LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2007 >> LS 460 >> Repair and Diagnosis >> External Pages >> Different car >> Section 527 (Body Control System) >> BCM (Body Control Module) >> Configuration >> Write Configuration Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Write Configuration Procedure

WARNING: This page is about a different car, the 2007 Nissan Maxima. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION: If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be detected in self-diagnosis depending on control unit which carries out CAN communication.
  1. With ignition switch OFF, connect CONSULT-II and CONSULT-II CONVERTER to data link connector and turn ignition switch ON.
    Fig 1: Connecting CONSULT-II And CONSULT-II Converter To Data Link Connector
    G04918148Courtesy of NISSAN MOTOR CO., U.S.A.
  2. Touch "START (NISSAN BASED VHCL)".
    Fig 2: CONSULT-II Function Screen Display - START (NISSAN BASED VHCL)
    G04918149Courtesy of NISSAN MOTOR CO., U.S.A.
  3. Touch "BCM" on "SELECT SYSTEM" screen.

    If "BCM" is not indicated, go to "CONSULT-II DATA LINK CONNECTOR (DLC) CIRCUIT ".

    Fig 3: CONSULT-II Function Screen Display - Select System
    G04918150Courtesy of NISSAN MOTOR CO., U.S.A.
  4. Touch "BCM" on "SELECT TEST ITEM" screen.
    Fig 4: CONSULT-II SELECT TEST ITEM Screen
    G04918151Courtesy of NISSAN MOTOR CO., U.S.A.
  5. Touch "CONFIGURATION" on "SELECT DIAG MODE" screen.
    Fig 5: CONSULT-II Function Screen Display - SELECT DIAG MODE
    G04918152Courtesy of NISSAN MOTOR CO., U.S.A.
  6. Touch "A34" and "OK" on "VEHICLE SELECT" screen. For canceling, touch "CANCEL" on "VEHICLE SELECT" screen.
    NOTE: Confirm vehicle model. Refer to "MODEL VARIATION ".
    Fig 6: CONSULT-II SELECT DIAG MODE Screen
    G04918153Courtesy of NISSAN MOTOR CO., U.S.A.
  7. Touch "WRITE CONFIGURATION" on "SELECT CONFIG ITEM" screen.
    Fig 7: CONSULT-II Function Screen Display - SELECT CONFIG ITEM
    G04918154Courtesy of NISSAN MOTOR CO., U.S.A.
  8. Touch "YES".

    For canceling, touch "NO".

    Fig 8: CONSULT-II Function Screen Display - CONFIGURATION
    G04918155Courtesy of NISSAN MOTOR CO., U.S.A.
  9. Touch "WITH" or "WITHOUT" on "WRITE CONFIGURATION" screen based on the following ITEM LIST.
    DISPLAY ITEM LIST REFERENCE

    ITEM SET VAL
    DTRL WITH ← → WITHOUT
    SPEED SENS WIP WITH ← → WITHOUT
    NOTE: Confirm vehicle model. Refer to "MODEL VARIATION ".
  10. Touch "CHNG SETTING" on "WRITE CONFIGURATION" screen.
    CAUTION: Make sure to touch "CHNG SETTING" even if the indicated configuration of new BCM is same as the desirable configuration.
    If not, configuration which is set automatically by selecting vehicle model cannot be memorized.
  11. Touch "OK" on "WRITE CONFIGURATION" screen.

    If "CANCEL" is touched, it will return to previous screen.

    Fig 9: CONSULT-II WRITE CONFIGURATION Screen
    G04918156Courtesy of NISSAN MOTOR CO., U.S.A.
  12. Wait until the next screen during setting.
    Fig 10: CONSULT-II WRITE CONFIGURATION Screen
    G04918157Courtesy of NISSAN MOTOR CO., U.S.A.
  13. WRITE CONFIGURATION results are printed out automatically. Check "WRITE CONFIGURATION" is correctly executed by comparing sheet automatically printed out with desirable configuration.
    Fig 11: CONSULT-II NISSAN WRITE CONFIGURATION Screen
    G04918158Courtesy of NISSAN MOTOR CO., U.S.A.
  14. Touch "OK" on "WRITE CONFIGURATION" screen. WRITE CONFIGURATION is completed.
    Fig 12: CONSULT-II WRITE CONFIGURATION Screen
    G04918159Courtesy of NISSAN MOTOR CO., U.S.A.
scientia non olet · About LEMON Manuals