LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2007 >> LS 460 >> Repair and Diagnosis >> External Pages >> Different car >> Section 764 (Engine Control System - Component Testing) >> Ignition Signal >> Diagnostic Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnostic Procedure

WARNING: This page is about a different car, the 2007 Nissan Quest. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK ENGINE START 

    Turn ignition switch OFF, and restart engine.

    Is engine running? 

    Yes or No 

    Yes (With CONSULT-II) >> GO TO 2.

    Yes (Without CONSULT-II) >> GO TO  3.

    No: GO TO  4.

  2. CHECK OVERALL FUNCTION 

    With CONSULT-II 

    1. Perform "POWER BALANCE" in "ACTIVE TEST" mode with CONSULT-II.
    2. Make sure that each circuit produces a momentary engine speed drop.

    OK or NG 

    OK: INSPECTION END 

    NG: GO TO  10.

    Fig 1: CONSULT-II Display - ACTIVE TEST
    G04900123Courtesy of NISSAN NORTH AMERICA, INC.
  3. CHECK OVERALL FUNCTION 

    Without CONSULT-II 

    1. Let engine idle.
    2. Read the voltage signal between ECM terminals 60, 61, 62, 79, 80, 81 and ground with an oscilloscope.
    3. Verify that the oscilloscope screen shows the signal wave as shown below.
      NOTE: The pulse cycle changes depending on rpm at idle.
      Fig 2: Checking Voltage Signal Between ECM Terminals 60, 61, 62, 79, 80, 81 And Ground
      G04905873Courtesy of NISSAN NORTH AMERICA, INC.
      Fig 3: Signal Waveform
      G04905874Courtesy of NISSAN NORTH AMERICA, INC.

    OK or NG 

    OK: INSPECTION END 

    NG: GO TO  10.

  4. CHECK IGNITION COIL POWER SUPPLY CIRCUIT-I 
    1. Turn ignition switch OFF, wait at least 10 seconds and then turn ON.
    2. Check voltage between ECM terminals 119, 120 and ground with CONSULT-II or tester.

      Voltage: Battery voltage 

    OK or NG 

    OK: GO TO 5.

    NG: GO to "POWER SUPPLY AND GROUND CIRCUIT ".

    Fig 4: Checking Voltage Between ECM Terminals 119, 120 And Ground
    G04900811Courtesy of NISSAN NORTH AMERICA, INC.
  5. CHECK IGNITION COIL POWER SUPPLY CIRCUIT-II 
    1. Turn ignition switch OFF.
    2. Disconnect condenser-1 harness connector.
    3. Turn ignition switch ON.
      Fig 5: Identifying Intake Manifold Collector
      G04905876Courtesy of NISSAN NORTH AMERICA, INC.
    4. Check voltage between condenser-1 terminal + and ground with CONSULT-II or tester.

      Voltage: Battery voltage 

    OK or NG 

    OK: GO TO  8.

    NG: GO TO 6.

    Fig 6: Checking Voltage Between Condenser Terminal And Ground
    G04905877Courtesy of NISSAN NORTH AMERICA, INC.
  6. CHECK IGNITION COIL POWER SUPPLY CIRCUIT-III 
    1. Turn ignition switch OFF.
    2. Disconnect IPDM E/R harness connector E122.
    3. Check harness continuity between IPDM E/R terminal 17 and condenser-1 terminal +. Refer to WIRING DIAGRAM .

      Continuity should exist. 

    4. Also check harness for short to ground and short to power.

    OK or NG 

    OK: GO to "POWER SUPPLY AND GROUND CIRCUIT ".

    NG: GO TO 7.

  7. DETECT MALFUNCTIONING PART 

    Check the following.

    • Harness connectors E5, F14
    • Harness for open or short between IPDM E/R and condenser-1

    : Repair open circuit or short to ground or short to power in harness or connectors.

  8. CHECK CONDENSER-1 GROUND CIRCUIT FOR OPEN AND SHORT 
    1. Turn ignition switch OFF.
    2. Check harness continuity between condenser-1 terminal - and ground. Refer to WIRING DIAGRAM .

      Continuity should exist. 

    3. Also check harness for short to power.

    OK or NG 

    OK: GO TO 9.

    NG: Repair open circuit or short to power in harness or connectors.

  9. CHECK CONDENSER-1 

    Refer to "COMPONENT INSPECTION ".

    OK or NG 

    OK: GO TO 10.

    NG: Replace condenser-1.

  10. CHECK IGNITION COIL POWER SUPPLY CIRCUIT-V 
    1. Turn ignition switch OFF.
    2. Reconnect all harness connectors disconnected.
    3. Disconnect ignition coil harness connector.
      Fig 7: Identifying Ignition Coil Harness Connector
      G04905864Courtesy of NISSAN NORTH AMERICA, INC.
    4. Turn ignition switch ON.
    5. Check voltage between ignition coil terminal 3 and ground with CONSULT-II or tester.

      Voltage: Battery voltage 

    OK or NG 

    OK: GO TO  12.

    NG: GO TO 11.

    Fig 8: Checking Voltage Between Ignition Coil Terminal 3 And Ground
    G04875257Courtesy of NISSAN NORTH AMERICA, INC.
  11. DETECT MALFUNCTIONING PART 

    Check the following.

    • Harness connectors F43, F201
    • Harness for open or short between ignition coil and harness connector F14

    : Repair or replace harness or connectors.

  12. CHECK IGNITION COIL GROUND CIRCUIT FOR OPEN AND SHORT 
    1. Turn ignition switch OFF.
    2. Check harness continuity between ignition coil terminal 2 and ground.

      Refer to WIRING DIAGRAM .

      Continuity should exist. 

    3. Also check harness for short to power.

    OK or NG 

    OK: GO TO  14.

    NG: GO TO 13.

  13. DETECT MALFUNCTIONING PART 

    Check the following.

    • Harness connectors F201, F43
    • Harness for open or short between ignition coil and ground

    : Repair open circuit or short to power in harness or connectors.

  14. CHECK IGNITION COIL OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT 
    1. Disconnect ECM harness connector.
    2. Check harness continuity between ECM terminals 60, 61, 62, 79, 80, 81 and ignition coil terminal 1.

      Refer to WIRING DIAGRAM .

      Continuity should exist. 

    3. Also check harness for short to ground and short to power.

    OK or NG 

    OK: GO TO  16.

    NG: GO TO 15.

  15. DETECT MALFUNCTIONING PART 

    Check the following.

    • Harness connectors F43, F201
    • Harness for open or short between ignition coil and ECM

    : Repair open circuit or short to ground or short to power in harness or connectors.

  16. CHECK IGNITION COIL WITH POWER TRANSISTOR 

    Refer to "COMPONENT INSPECTION ".

    OK or NG 

    OK: GO TO 17.

    NG: Replace malfunctioning ignition coil with power transistor.

  17. CHECK INTERMITTENT INCIDENT 

    Refer to "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT ".

    : INSPECTION END 

scientia non olet · About LEMON Manuals