LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2007 >> LS 460 >> Repair and Diagnosis >> External Pages >> Different car >> Section 776 (Engine Control System - Component Testing) >> Fuel Injector >> Diagnostic Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnostic Procedure

WARNING: This page is about a different car, the 2007 Nissan Pathfinder. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSPECTION START 

    Turn ignition switch to START.

    Is any cylinder ignited? 

    Yes or No 

    Yes (With CONSULT-II): GO TO 2.

    Yes (Without CONSULT-II): GO TO  3.

    No: GO TO  7.

  2. CHECK OVERALL FUNCTION 

    With CONSULT-II 

    1. Start engine.
    2. Perform "POWER BALANCE" in "ACTIVE TEST" mode with CONSULT-II.
      Fig 1: Identifying CONSULT-II Display - ACTIVE TEST
      G04900123Courtesy of NISSAN NORTH AMERICA, INC.
    3. Make sure that each circuit produces a momentary engine speed drop.

    OK or NG 

    OK: INSPECTION END 

    NG: GO TO  7.

  3. CHECK FUNCTION OF FUEL INJECTOR-I 

    Without CONSULT-II 

    1. Stop engine.
    2. Disconnect harness connector F44, F101.
      Fig 2: Identifying Harness Connector F44 And F101
      G04896951Courtesy of NISSAN NORTH AMERICA, INC.
    3. Turn ignition switch ON.
    4. Check voltage between harness connector F44 terminal 3 and ground with CONSULT-II or tester.

      Voltage: Battery voltage 

      Fig 3: Checking Voltage Between Harness Connector F44 Terminal 3 And Ground
      G04896952Courtesy of NISSAN NORTH AMERICA, INC.
    5. Turn ignition switch OFF.
    6. Disconnect ECM harness connector.
    7. Check harness continuity between harness connector F44 and ECM as follows.

      Refer to Wiring Diagram .

      CONTINUITY REFERENCE CHART

      Cylinder Harness connector F44 terminal ECM terminal
      1 2 23
      3 1 22
      5 4 21

      Continuity should exist  .

    8. Also check harness for short to ground and short to power.

    OK or NG 

    OK: GO TO  5.

    NG: GO TO 4.

  4. DETECT MALFUNCTIONING PART 

    Check the following.

    • Harness connectors E2, F32
    • IPDM E/R harness connector E119
    • 15A fuse
    • Harness for open or short between harness connector F44 and fuse
    • Harness for open or short between harness connector F101 and fuel injector

    Repair open circuit or short to ground or short to power in harness or connectors.

  5. CHECK FUNCTION OF FUEL INJECTOR-II 

    Provide battery voltage between harness connector F101 as follows and then interrupt it. Listen to each fuel injector operating sound.

    VOLTAGE CHART

    Cylinder Harness connector F101 terminal
    (+) (-)
    1 3 2
    3 3 1
    5 3 4

    Operating sound should exist  .

    Fig 4: Applying Battery Voltage Between Harness Connector F101
    G04896953Courtesy of NISSAN NORTH AMERICA, INC.

    OK or NG 

    OK: GO TO 6.

    NG: GO TO  7.

  6. CHECK FUNCTION OF FUEL INJECTOR-III 
    1. Reconnect all harness connector disconnected.
    2. Start engine.
    3. Listen to fuel injectors No. 2, No. 4, No. 6 operating sound.

      Clicking noise should exist  .

      Fig 5: Checking Fuel Injector
      G04900354Courtesy of NISSAN NORTH AMERICA, INC.

    OK or NG 

    OK: INSPECTION END 

    NG: GO TO 7.

  7. CHECK FUEL INJECTOR POWER SUPPLY CIRCUIT 
    1. Turn ignition switch OFF.
    2. Disconnect fuel injector harness connector.
      Fig 6: Identifying Fuel Injector Harness Connector
      G04897401Courtesy of NISSAN NORTH AMERICA, INC.
    3. Turn ignition switch ON.
    4. Check voltage between fuel injector terminal 1 and ground with CONSULT-II or tester.

      Voltage: Battery voltage 

      Fig 7: Checking Voltage Between Fuel Injector Terminal 1 And Ground
      G04900780Courtesy of NISSAN NORTH AMERICA, INC.

    OK or NG 

    OK: GO TO  9.

    NG: GO TO 8.

  8. DETECT MALFUNCTIONING PART 

    Check the following.

    • Harness connectors E2, F32
    • Harness connectors F44, F101
    • IPDM E/R harness connector E119
    • 15A fuse
    • Harness for open or short between fuel injector and fuse

    Repair harness or connectors.

  9. CHECK FUEL INJECTOR OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT 
    1. Turn ignition switch OFF.
    2. Disconnect ECM harness connector.
    3. Check harness continuity between fuel injector terminal 2 and ECM terminals 21, 22, 23, 40, 41, 42. Refer to Wiring Diagram .

      Continuity should exist  .

    4. Also check harness for short to ground and short to power.

    OK or NG 

    OK: GO TO  11.

    NG: GO TO 10.

  10. DETECT MALFUNCTIONING PART 

    Check the following.

    • Harness connectors F101, F44
    • Harness for open or short between fuel injector and ECM

    Repair open circuit or short to ground or short to power in harness or connectors.

  11. CHECK FUEL INJECTOR 

    Refer to "COMPONENT INSPECTION ".

    OK or NG 

    OK: GO TO 12.

    NG: Replace fuel injector.

  12. CHECK INTERMITTENT INCIDENT 

    Refer to "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT ".

    INSPECTION END 

scientia non olet · About LEMON Manuals