Customize Parameters

HINT:

The following items can be customized.

1. Connect the intelligent tester or Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the tester on.
4. Enter the following menus:
   1. Intelligent tester - Select: CUSTOMIZE /
   2. Techstream - Select: Customize Setting /
5. Select the setting by referring to the table below.
   1. Intelligent tester

      SMART 

      INTELLIGENT TESTER - SMART
      
      

      Display (Item)	Default	Contents	Setting
      PARK WAIT TIME (Waiting time to permit unlocking door after locking)	2.5s	Function that sets waiting time to permit unlocking door after door is locked with entry lock function	0.5s/1.5s/2.5s/5s
      TRUNK OPEN MODE (Luggage compartment door open mode when vehicle is locked)	ON	Function to permit opening luggage compartment door	ON / OFF

      WARNING 

      INTELLIGENT TESTER - WARING
      
      

      Display (Item)	Default	Contents	Setting
      KEY LOW-BATT WRN (Warn when key battery becomes weak)	ON	Function that warns driver that key's battery power is low	ON / OFF

   2. Techstream

      Smart Key / Access 

      TECHSTREAM - SMART KEY / ACCESS
      
      

      Display (Item)	Default	Contents	Setting
      Park Wait Time (Waiting time to permit unlocking door after locking)	2.5s	Function that sets waiting time to permit unlocking door after door is locked with entry lock function	0.5s/1.5s/2.5s/5s
      Trunk Open Mode (Luggage compartment door open mode when vehicle is locked)	ON	Function to permit opening luggage compartment door	ON / OFF

      Warning 

      TECHSTREAM - WARNING
      
      

      Display (Item)	Default	Contents	Setting
      Key Low Battery Warning (Warn when key battery becomes weak)	ON	Function that warns driver that key's battery power is low	ON / OFF

1. To use the entry unlock mode switching function, make sure the engine switch is off and simultaneously press and hold the key's LOCK switch and another key switch for 5 seconds. When the switches are pressed and held for 5 seconds, the entry door unlock mode changes in the following order: driver door unlock mode, one door unlock mode, doors on one side unlock mode, all door unlock mode.
   NOTE: After pressing and holding the switches for 5 seconds, wait 5 seconds before performing the same procedure again.
   • One door unlock mode:

     When a touch sensor is touched, the touch sensor's door unlocks. For example, if the driver door's touch sensor is touched, the driver door unlocks.

   • All door unlock mode:

     When a touch sensor is touched, all doors unlock.

   • Driver door unlock mode (default):

     When the driver door's touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.

   • Doors on one side unlock mode:

     When a touch sensor is touched, the doors on the side of the touch sensor unlock. For example, when the driver door's touch sensor is touched, the driver door and driver side rear door unlock.

2. The certification ECU receives this signal from the entry door control receiver and changes the smart access system with push-button start to the entry unlock mode.
3. The certification ECU sounds the wireless door lock buzzer and combination meter buzzer to inform the user that the mode has been switched.
   Fig 1: Identifying Multi-Information Display

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   HINT:

   The function only changes the entry unlock mode of the smart access system with push-button start. It does not switch the unlocking of the wireless door lock control.

   • One door mode:
     Fig 2: Unlock Mode Switching Function Chart - One Door Mode

     Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   • All door unlock mode:
     Fig 3: Unlock Mode Switching Function Chart - All Door Unlock Mode

     Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   • Driver door unlock mode:
     Fig 4: Driver Door Unlock Mode:

     Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   • Doors on one side mode:
     Fig 5: Unlock Mode Switching Function Chart - Doors On One Side Mode

     Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

The key cancel operation disables the following functions:

• Entry Ignition
• Entry Unlock / Lock
• Entry Luggage Compartment Open
• Key Lock-in Prevention
• Warning
• Memory Call
  1. The operation procedures are as follows:

     Precondition:

     Engine switch off, driver side door closed and unlocked.

     1. Unlock the driver side door once with the UNLOCK switch of the key.
     2. Open the driver door within 5 seconds.
     3. Unlock the driver side door twice with the UNLOCK switch of the key within 5 seconds.
     4. Perform close → open twice for the driver door within 30 seconds.

        (Driver door: Open condition → Close → Open → Close → Open)

     5. Unlock the driver side door twice with the UNLOCK switch of the key within 5 seconds.
     6. Perform close → open once for the driver door within 30 seconds.

        (Driver door: Open condition → Close → Open)

     7. Close the driver door within 5 seconds.

        When key cancel is activated, the wireless door lock buzzer sounds twice.

        To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.