LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2007 >> LS 460L >> Repair and Diagnosis >> Accessories & Equipment >> Cruise Control Systems >> Cruise Control >> Cruise Control System >> Data List / Active Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test

  1. DATA LIST 

    HINT:

    Using the intelligent tester or Techstream to read the DATA LIST allows values or status of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the DATA LIST information early in troubleshooting is one way to save diagnostic time.

    NOTE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
    1. Warm up the engine.
    2. Turn the engine switch to off.
    3. Connect the intelligent tester or Techstream to the DLC3.
    4. Turn the engine switch to on (IG).
    5. Turn the tester on.
    6. Using the intelligent tester or Techstream, enter the following menus:
      1. Intelligent tester - Select: DIAGNOSIS / OBD/ MOBD / (desired system) / DATA LIST / ALL /
      2. Techstream - Select: All ECUs / (desired system) / Data List /
    7. According to the display on tester, read the "DATA LIST".
      1. Intelligent tester

        CCS 

        INTELLIGENT TESTER - CCS

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        VEHICLE SPD Vehicle speed / min.: 0 km/h (0 mph) max.: 255 km/h (159 mph) Actual vehicle speed is display -
        MEMORY SPD Vehicle speed / mm.: 0 km/h (0 mph) max.: 255 km/h (159 mph) Actual vehicle speed stored in memory -
        CCS OPER STATUS Shift lever position signal / ON or OFF ON: Shift lever position D (8th, 7th, 6th, 5th or 4th gear)
        OFF: Shift lever position except D (8th, 7th, 6th, 5th or 4th gear)        		 -
        CRUISE CONTROL Cruise control / ON or OFF ON: Cruise control is SET
        OFF: Cruise control is UNSET        		 -
        CCS INDICATOR M CRUISE main indicator (Main CPU) / ON or OFF ON: CRUISE main indicator light is ON
        OFF: CRUISE main indicator light is OFF        		 -
        CCS READY M Cruise control system standby condition (Main CPU) / ON or OFF ON: CRUISE main indicator light is ON
        OFF: CRUISE main indicator light is OFF        		 -
        MAIN SW (MAIN) Cruise control switch (Main CPU) /ON or OFF ON: Cruise control switch is ON
        OFF: Cruise control switch is OFF        		 -
        CANCEL SW CANCEL switch / ON or OFF ON: CANCEL switch is ON
        OFF: CANCEL switch is OFF        		 -
        SET/COAST SW -/SET switch / ON or OFF ON: -/SET switch is ON
        OFF: -/SET switch is OFF        		 -
        RES/ACC SW +/RES switch / ON or OFF ON: +/RES switch is ON
        OFF: +/RES switch is OFF        		 -
        STP LIGHT SW M Stop light switch signal (Main CPU) / ON or OFF ON: Brake pedal depressed
        OFF: Brake pedal released        		 -
        RQST TORQUE Cruise control request torque / min.: -1,024 Nm, max.: 1,016 Nm Actual required torque -

        METER 

        INTELLIGENT TESTER - METER

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        SPEED METER Vehicle speed / min.: 0 km/h (0 mph) max.: 255 km/h (159 mph) Actual vehicle speed is display -
      2. Techstream

        Cruise Control 

        TECHSTREAM - CRUISE CONTROL

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        CCS Vehicle Spd Vehicle speed / min.: 0 km/h (0 mph) max.: 255 km/h (159 mph) Actual vehicle speed is display -
        CCS Mem Vehicle Spd Vehicle speed / min.: 0 km/h (0 mph) max.: 255 km/h (159 mph) Actual vehicle speed stored in memory -
        CCS Operation Status Shift lever position signal / ON or OFF ON: Shift lever position D (8th, 7th, 6th, 5th or 4th gear)
        OFF: Shift lever position except D (8th, 7th, 6th, 5th or 4th gear)        		 -
        Cruise Control Cruise control / ON or OFF ON: Cruise control is SET
        OFF: Cruise control is UNSET        		 -
        CCS Indicator M-CPU CRUISE main indicator (Main CPU)/ON or OFF ON: CRUISE main indicator light is ON
        OFF: CRUISE main indicator light is OFF        		 -
        CCS Ready M-CPU Cruise control system standby condition (Main CPU) / ON or OFF ON: Cruise control main switch (Main CPU) is SET
        OFF: Cruise control main switch (Main CPU) is UNSET        		 -
        CCS Main SW M-CPU Cruise control switch (Main CPU) / ON or OFF ON: Cruise control switch is ON
        OFF: Cruise control switch is OFF        		 -
        Cancel Switch CANCEL switch / ON or OFF ON: CANCEL switch is ON
        OFF: CANCEL switch is OFF        		 -
        SET/COAST Switch -/SET switch / ON or OFF ON: -/SET switch is ON
        OFF: -/SET switch is OFF        		 -
        RES/ACC Switch +/RES switch / ON or OFF ON: +/RES switch is ON
        OFF: +/RES switch is OFF        		 -
        Stop Light SW M-CPU Stop light switch signal (Main CPU)/ON or OFF ON: Brake pedal depressed
        OFF: Brake pedal released        		 -
        CCS Request Torque Cruise control request torque / min.: -1,024 Nm, max.: 1,016 Nm Actual required torque -

        Combination Meter 

        TECHSTREAM - COMBINATION METER

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        Speed Meter Vehicle speed / min.: 0 km/h (0 mph) max.: 255 km/h (159 mph) Actual vehicle speed is display -
  2. ACTIVE TEST 

    HINT:

    Using the intelligent tester or Techstream to perform ACTIVE TEST allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing ACTIVE TEST early in troubleshooting is one way to save diagnostic time. DATA LIST information can be displayed while performing ACTIVE TEST.

    1. Warm up the engine.
    2. Turn the engine switch to off.
    3. Connect the intelligent tester or Techstream to the DLC3.
    4. Turn the engine switch to on (IG).
    5. Turn the tester on.
    6. Enter the following menus:
      1. Intelligent tester - Select: DIAGNOSIS / OBD/ MOBD / METER / ACTIVE TEST / ALL DATA /
      2. Techstream - Select: Body / Combination Meter / Active Test /
    7. According to the display on tester, perform the "ACTIVE TEST".
      1. Intelligent tester

        METER 

        INTELLIGENT TESTER - METER

        Tester Display Test Part Control Range Diagnostic Note
        CRUISE INDIC CRUISE main indicator ON / OFF -
      2. Techstream

        Combination Meter 

        TECHSTREAM - COMBINATION METER

        Tester Display Test Part Control Range Diagnostic Note
        Indic. Lamp Cruise CRUISE main indicator ON / OFF -
scientia non olet · About LEMON Manuals