LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2007 >> LS 460L >> Repair and Diagnosis >> Accessories & Equipment >> Cruise Control Systems >> Cruise Control >> Dynamic Radar Cruise Control System >> Data List / Active Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test

  1. DATA LIST 

    HINT:

    Using the intelligent tester or Techstream to read the DATA LIST allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the DATA LIST information early in troubleshooting is one way to save diagnostic time.

    NOTE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
    1. Connect the intelligent tester or Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the tester on.
    4. Using the intelligent tester or Techstream, enter the following menus:
      1. Intelligent tester - Select: DIAGNOSIS / OBD/ MODE / (desired system) / DATA LIST / ALL.
      2. Techstream - Select: All ECUs / (desired system) / Data List.
    5. Check the values by referring to the table below.
      1. Intelligent tester

        RADAR CRUISE 

        INTELLIGENT TESTER - RADAR CRUISE

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        MAIN SW Cruise control main switch signal/ ON or OFF ON: Cruise control main switch ON
        OFF: Cruise control main switch OFF        		 -
        RES/ACC SW +/RES switch signal/ON or OFF ON: +/RES switch ON
        OFF: +/RES switch OFF        		 -
        SET/COAST SW -/SET switch signal/ON or OFF ON: -/SET switch ON
        OFF: -/SET switch OFF        		 -
        CONST SPD MODE Constant speed mode signal/ON or OFF ON: Dynamic radar cruise control system is constant speed mode
        OFF: Dynamic radar cruise control system is vehicle-to-vehicle mode        		 -
        DIST CTRL SW Distance control switch signal/ON or OFF ON: Distance control switch ON
        OFF: Distance control switch OFF        		 -
        SNOW SW ECT SNOW switch signal/ON or OFF ON: ECT SNOW switch ON
        OFF: ECT SNOW switch OFF        		 -
        STP LIGHT SW1-M Stop light switch (Main-CPU) signal/ON or OFF OK: Depress brake pedal
        OFF: Release brake pedal        		 -
        STP LIGHT SW2-M Stop light switch (Main-CPU) signal/ON or OFF OK: Depress brake pedal
        OFF: Release brake pedal        		 -
        STP LIGHT SW1-S Stop light switch (Sub-CPU) signal/ON or OFF OK: Depress brake pedal
        OFF: Release brake pedal        		 -
        WIPER-INTERMIT Windshield wiper switch INT signal/ON or OFF ON: Windshield wiper switch INT
        OFF: Windshield wiper switch except INT        		 -
        WIPER-LO Windshield wiper Lo switch Lo signal/ON or OFF ON: Windshield wiper switch Lo
        OFF: Windshield wiper switch except Lo        		 -
        WIPER-HI Windshield wiper Lo switch Hi signal/ON or OFF ON: Windshield wiper switch Hi
        OFF: Windshield wiper switch except Hi        		 -
        WIPER STOP POS Wiper stop position signal/ON or OFF ON: Wiper stop position normally
        OFF: Wiper stop position abnormally        		 -
        V SPD(WHEEL) Vehicle speed/min.: -327 km/h (-523 mph) max.: 327 km/h (523 mph) Actual vehicle speed stored -
        V SPD(ECU) Vehicle speed/min.: -327 km/h (-523 mph) max.: 327 km/h (523 mph) Actual vehicle speed stored -
        INVALID SENSORS Vehicle speed/min.: 0 km/h (0 mph) max.: 255 km/h (408 mph) Actual vehicle speed stored -
        CRUISE CONTROL Cruise control system operation signal/ON or OFF ON: Cruise control system operating
        OFF: Cruise control system not operating        		 -
        CCS TERMINATE Cruise control terminate request signal/ON or OFF ON: Cruise control system operating
        OFF: Cruise control system not operating        		 -
        CCS MODE Cruise control mode signal/Hi Spd or Normal Hi Spd: Vehicle-to-vehicle distance code mode
        Normal: Constant speed mode        		 -
        Country# (ECU) Driving support ECU country signal/JPN, NA, EURO, GEN Actual country code -
        Country# (FRS) Front millimeter wave radar sensor country signal/JPN, NA, EURO, GEN Actual country code -
        FL W SPD SENSOR Front wheel speed sensor LH signal/Normal or Abnormal Normal: Wheel speed sensor normal
        Abnormal: Wheel speed sensor abnormal        		 -
        FR W SPD SENSOR Front wheel speed sensor RH signal/Normal or Abnormal Normal: Wheel speed sensor normal
        Abnormal: Wheel speed sensor abnormal        		 -
        RL W SPD SENSOR Rear wheel speed sensor LH signal/Normal or Abnormal Normal: Wheel speed sensor normal
        Abnormal: Wheel speed sensor abnormal        		 -
        RR W SPD SENSOR Rear wheel speed sensor RH signal/Normal or Abnormal Normal: Wheel speed sensor normal
        Abnormal: Wheel speed sensor abnormal        		 -
        YAW RATE Yaw rate value/min.: -100 deg/s, max.: 100 deg/s Min.; -100 deg/s
        Max.: 100 deg/s        		 -
        STEERING ANGLE Steering angle value/min.: -3072 deg, max.: 3070.5 deg Min.: -3072 deg
        Max.: 3070.5 deg        		 -
        ZERO POINT Zero point value/min.: -3072 deg, max.: 3070.5 deg Min.: -3072 deg
        Max.: 3070.5 deg        		 -
        DECELERAT SEN Deceleration sensor value/min.: -14.7 m/s2 , max.: 14.7 m/s2 Min.: -14.7 m/s2
        Max.: 14.7 m/s2        		 -
        DECELERAT SEN 2 Deceleration sensor value/min.: -14.7 m/s2 , max.: 14.7 m/s2 Min.: -14.7 m/s2
        Max.: 14.7 m/s2        		 -
        ZERO DECELERAT1 Zero point deceleration sensor value/min.: -4.5952 m/s2 max.: 4.5593 m/s2 Min.: -4.5952 m/s2
        Max.: 4.5593 m/s2        		 -
        ZERO DECELERAT2 Zero point deceleration sensor value/min.: -4.5952 m/s2 max.: 4.5593 m/s2 Min.: -4.5952 m/s2
        Max.: 4.5593 m/s2        		 -
        BRAKE CONTROL Brake control signal/ON or OFF ON: Depress brake pedal
        OFF: Release brake pedal        		 -
        VEHICLE STOP Vehicle stop signal/ON or OFF ON: Vehicle stop
        OFF: Vehicle running        		 -

        CCS 

        INTELLIGENT TESTER - CCS

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        CCS READY M-CPU Cruise control system standby condition (Main CPU)/ON or OFF ON: Cruise control main switch (Main CPU) is SET
        OFF: Cruise control main switch (Main CPU) is UNSET        		 -
        CCS INDICATOR M-CPU Cruise indicator signal (Main CPU)/ON or OFF ON: CRUISE main indicator light is ON
        OFF: CRUISE main indicator light is OFF        		 -

        STEERING PAD 

        INTELLIGENT TESTER - STEERING PAD

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        ACC SW Steering pad switch with modulator (distance control switch) signal/ON or OFF ON: Steering pad switch with modulator (distance control switch) is ON
        OFF: Steering pad switch with modulator (distance control switch) is OFF        		 -
      2. Techstream

        Radar Cruise 

        TECHSTREAM - RADAR CRUISE

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        Cruise Control Main Switch Cruise control switch signal/ON or OFF ON: Cruise control switch ON
        OFF: Cruise control switch OFF        		 -
        RES/ACC Switch +/RES switch signal/ON or OFF ON: +/RES switch ON
        OFF: +/RES switch OFF        		 -
        SET/COAST Switch -/SET switch signal/ON or OFF ON: -/SET switch ON
        OFF: -/SET switch OFF        		 -
        Constant Speed Mode Constant speed mode signal/ON or OFF ON: Dynamic radar cruise control system is constant speed mode
        OFF: Dynamic radar cruise control system is vehicle-to-vehicle mode        		 -
        Distance Control Switch Distance control switch signal/ON or OFF ON: Distance control switch ON
        OFF: Distance control switch OFF        		 -
        Snow Switch ECT SNOW switch signal/ON or OFF ON: ECT SNOW switch ON
        OFF: ECT SNOW switch OFF        		 -
        Stop Light SW 1 (M CPU) Stop light switch (Main-CPU) signal/ON or OFF OK: Depress brake pedal
        OFF: Release brake pedal        		 -
        Stop Light SW 2 (M CPU) Stop light switch (Main-CPU) signal/ON or OFF OK: Depress brake pedal
        OFF: Release brake pedal        		 -
        Stop Light SW 1 (S CPU) Stop light switch (Sub-CPU) signal/ON or OFF OK: Depress brake pedal
        OFF: Release brake pedal        		 -
        Wiper (Intermit) Windshield wiper switch INT signal/ON or OFF ON: Windshield wiper switch INT
        OFF: Windshield wiper switch except INT        		 -
        Wiper (Lo) Windshield wiper Lo switch Lo signal/ON or OFF ON: Windshield wiper switch Lo
        OFF: Windshield wiper switch except Lo        		 -
        Wiper (Hi) Windshield wiper Lo switch Hi signal/ON or OFF ON: Windshield wiper switch Hi
        OFF: Windshield wiper switch except Hi        		 -
        Wiper Stop Position Wiper stop position signal/ON or OFF ON: Wiper stop position normally
        OFF: Wiper stop position abnormally        		 -
        Vhcl Spd Calc-Whl Spd Vehicle speed/min.: -327 km/h (-523 mph), max.: 327 km/h (523 mph) Actual vehicle speed stored -
        Vhcl Spd-Brake ECU Vehicle speed/min.: -327 km/h (-523 mph), max.: 327 km/h (523 mph) Actual vehicle speed stored -
        Invalid Whl Spd Sens Num Vehicle speed/min.: 0 km/h (0 mph), max.: 255 km/h (408 mph) Actual vehicle speed stored -
        Cruise Control Cruise control system operation signal/ON or OFF ON: Cruise control system operating
        OFF: Cruise control system not operating        		 -
        CCS Terminate Request Cruise control terminate request signal/ON or OFF ON: Cruise control system not operating
        OFF: Cruise control system operating        		 -
        CCS Mode Cruise control mode signal/Hi Spd or Normal Hi Spd: Vehicle-to-vehicle distance code mode
        Normal: Constant speed mode        		 -
        Country# (F Radar Sens) Front millimeter wave radar sensor country signal/JPN, NA, EURO, GEN Actual country code -
        Country# (DSS) Driving support ECU country signal/JPN, NA, EURO, GEN Actual country code -
        Front Whl Spd LH Sensor Front wheel speed sensor LH signal/Normal or Abnormal Normal: Wheel speed sensor normal
        Abnormal: Wheel speed sensor abnormal        		 -
        Front Whl Spd RH Sensor Front wheel speed sensor RH signal/Normal or Abnormal Normal: Wheel speed sensor normal
        Abnormal: Wheel speed sensor abnormal        		 -
        Rear Whl Spd LH Sensor Rear wheel speed sensor LH signal/Normal or Abnormal Normal: Wheel speed sensor normal
        Abnormal: Wheel speed sensor abnormal        		 -
        Rear Whl Spd RH Sensor Rear wheel speed sensor RH signal/Normal or Abnormal Normal: Wheel speed sensor normal
        Abnormal: Wheel speed sensor abnormal        		 -
        Yaw Rate Sensor Yaw rate value/min.: -100 deg/s, max.: 100 deg/s Min.; -100 deg/s
        Max.: 100 deg/s        		 -
        Steering Angle Steering angle value/min.: -3072 deg, max.: 3070.5 deg Min.: -3072 deg
        Max.: 3070.5 deg        		 -
        Zero Point Angle Sens Zero point value/min.: -3072 deg, max.: 3070.5 deg Min.: -3072 deg
        Max.: 3070.5 deg        		 -
        Deceleration Sensor 1 Deceleration sensor value/min.: -14.7 m/s2 , max.: 14.7 m/s2 Min.:-14.7 m/s2
        Max.: 14.7 m/s2        		 -
        Deceleration Sensor 2 Deceleration sensor value/min.: -14.7 m/s2 , max.: 14.7 m/s2 Min.: -14.7 m/s2
        Max.: 14.7 m/s2        		 -
        Zero Deceleration Sensor 1 Zero point deceleration sensor value/min.: -4.5952 m/s2 max.: 4.5593 m/s2 Min.: -4.5952 m/s2
        Max.: 4.5593 m/s2        		 -
        Zero Deceleration Sensor 2 Zero point deceleration sensor value/min.: -4.5952 m/s2 max.: 4.5593 m/s2 Min.: -4.5952 m/s2
        Max.: 4.5593 m/s2        		 -
        Brake Control Brake control signal/ON or OFF ON: Depress brake pedal
        OFF: Release brake pedal        		 -
        Vehicle Stop Vehicle stop signal/ON or OFF ON: Vehicle stop
        OFF: Vehicle running        		 -

        Cruise Control 

        TECHSTREAM - CRUISE CONTROL

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        CCS Ready M Cruise control system standby condition (Main CPU)/ON or OFF ON: Switch ready (Main CPU) is SET
        OFF: Switch ready (Main CPU) is UNSET        		 -
        CCS Indicator M Cruise indicator signal (Main CPU)/ON or OFF ON: "CCS READY" ON
        OFF: "CCS READY" OFF        		 -

        Steering Pad Switch 

        TECHSTREAM - STEERING PAD SWITCH

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        ACC SW Steering pad switch with modulator (distance control switch) signal/ON or OFF ON: Steering pad switch with modulator (distance control switch) is ON
        OFF: Steering pad switch with modulator (distance control switch) is OFF        		 -
  2. ACTIVE TEST 

    HINT:

    Using the intelligent tester or Techstream to perform ACTIVE TEST allows relays, VSVs, actuators and parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing ACTIVE TEST early in troubleshooting is one way to save diagnostic time. DATA LIST information can be display while performing ACTIVE TEST.

    1. Connect the intelligent tester or Techstream to the DLC3.
    2. Turn the engine switch to on (IG).
    3. Turn the tester on.
    4. Using the intelligent tester or Techstream, enter the following menus:
      1. Intelligent tester - Select: DIAGNOSIS/OBD/ MODE / (desired system) /ACTIVE TEST.
      2. Techstream - Select: Body Electrical /(desired system) / Active Test / All.
    5. Perform the Active Test by referring to the table below.
      1. Intelligent tester

        METER 

        INTELLIGENT TESTER - METER

        Tester Display Test Part Control Range Diagnostic Note
        CRUISE INDIC CRUISE main indicator light ON/OFF -

        ABS/VSC 

        INTELLIGENT TESTER - ABS/VSC

        Tester Display Test Part Control Range Diagnostic Note
        BUZZER Skid control buzzer sounds ON/OFF -
      2. Techstream

        Combination Meter 

        TECHSTREAM - COMBINATION METER

        Tester Display Test Part Control Range Diagnostic Note
        Indicat. Lamp Cruise CRUISE main indicator light ON/OFF -

        ABS/VSC/TRAC 

        TECHSTREAM - ABS/VSC/TRAC

        Tester Display Test Part Control Range Diagnostic Note
        Buzzer Skid control buzzer sounds ON/OFF -
scientia non olet · About LEMON Manuals