Reference Value From Consult-II

WARNING: This page is about a different car, the 2005 Nissan Titan. However, it is still accessible from the selected car via links, so may be relevant.

CAUTION: The display shows the control unit calculation data, so a normal value might be displayed even in the event the output circuit (harness) is open or short circuited.

REFERENCE VALUE FROM CONSULT-II CHART

Monitor item	Display content	Data monitor		NOTE: Error inspection checklist
Monitor item	Display content	Condition	Reference value in normal operation	NOTE: Error inspection checklist
N POSI SIG	PNP switch signal ON/OFF condition	A/T shift position = N position	ON	, "CAN Communication System Inspection "
N POSI SIG	PNP switch signal ON/OFF condition	A/T shift position = other than N positions	OFF	, "CAN Communication System Inspection "
P POSI SIG	PNP switch signal ON/OFF condition	A/T shift position P position	ON	, "CAN Communication System Inspection "
P POSI SIG	PNP switch signal ON/OFF condition	A/T shift position = other than P positions	OFF	, "CAN Communication System Inspection "
GEAR	A/T gear position	1st gear	1	-
		2nd gear	2
		3rd gear	3
		4th gear	4
		5th gear	5
FR RH SENSOR FR LH SENSOR RR RH SENSOR RR LH SENSOR	Wheel speed	Vehicle stopped	0 [km/h (MPH)]	, "WHEEL SENSOR SYSTEM "
FR RH SENSOR FR LH SENSOR RR RH SENSOR RR LH SENSOR	Wheel speed	Vehicle running (Note 1)	Almost in accordance with speedometer display (within +/-10%)	, "WHEEL SENSOR SYSTEM "
BATTERY VOLT	Battery voltage supplied to ABS actuator and electric unit (control unit)	Ignition switch ON	10 to 16V	, "ABS Control Unit Power and Ground Systems Inspection "
STOP LAMP SW	Stop lamp switch operation	Brake pedal depressed	ON	-
STOP LAMP SW	Stop lamp switch operation	Brake pedal not depressed	OFF	-
ABS WARN LAMP	ABS warning lamp ON condition (Note 2)	ABS warning lamp ON	ON	, "ABS Warning Lamp Does Not Come On When Ignition Switch Is Turned On "
ABS WARN LAMP	ABS warning lamp ON condition (Note 2)	ABS warning lamp OFF	OFF
MOTOR RELAY	Operation status of motor and motor relay	Ignition switch ON or running (ABS not activated)	OFF	, "ACTUATOR MOTOR, MOTOR RELAY, AND CIRCUIT INSPECTION "
MOTOR RELAY	Operation status of motor and motor relay	Ignition switch ON or engine running (ABS activated)	ON	, "ACTUATOR MOTOR, MOTOR RELAY, AND CIRCUIT INSPECTION "
ACTUATOR RLY	Actuator relay operation status	Vehicle stopped (Ignition switch ON)	OFF	, "ACTUATOR MOTOR, MOTOR RELAY, AND CIRCUIT INSPECTION "
ACTUATOR RLY	Actuator relay operation status	Vehicle stopped (Engine running)	ON	, "ACTUATOR MOTOR, MOTOR RELAY, AND CIRCUIT INSPECTION "
FR LH IN SOL FR LH OUT SOL FR RH IN SOL FR RH OUT SOL REAR IN SOL REAR OUT SOL	Solenoid valve operation	Actuator (solenoid) is active ("ACTIVE TEST" with CONSULT-II) or actuator relay is inactive (in fail-safe mode).	ON	, "SOLENOID VALVE SYSTEM INSPECTION "
	Solenoid valve operation	When actuator (solenoid) is not active and actuator relay is active (ignition switch ON).	OFF	, "SOLENOID VALVE SYSTEM INSPECTION "
FLUID LEV SW	ON/OFF status of brake fluid level switch	When brake fluid level switch ON	ON	WARNING LAMPS
FLUID LEV SW	ON/OFF status of brake fluid level switch	When brake fluid level switch OFF	OFF	WARNING LAMPS
ABS SIGNAL EBD SIGNAL	Signal status	ABS active EBD active	ON	ABS system EBD system
ABS SIGNAL EBD SIGNAL	Signal status	ABS not active EBD not active	OFF	ABS system EBD system
ABS FAIL SIG EBD FAIL SIG	Fail signal status	ABS fail EBD fail	ON	ABS system EBD system
ABS FAIL SIG EBD FAIL SIG	Fail signal status	ABS normal EBD normal	OFF	ABS system EBD system
NOTE: 1: Confirm tire pressure is normal. NOTE: 2: ON/OFF timing of ABS warning lamp ON: For approximately 2 seconds after ignition switch is turned ON, or when a malfunction is detected. OFF: Approximately 2 seconds after ignition switch is turned ON (when system is in normal operation).