Data List / Active Test
- READ DATA LIST
HINT:
Using the Intelligent tester or Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.- Connect the Intelligent tester or Techstream to the DLC3.
- Turn the engine switch on (IG) and press the tester main switch ON.
- Enter the following menus:
- Intelligent tester - Select: DIAGNOSIS / OBD/ MOBD / CHASSIS / AIR SUSPENSION / DATA LIST/
- Techstream - Select: Chassis / Air suspension / Data List /
- Read the DATA LIST by following the directions on the tester screen.
- Intelligent tester
AIR SUSPENSION
INTELLIGENT TESTER - AIR SUSPENSION SPECIFICATIONTester Display Measurement Item/Range Normal Condition Diagnostic Note (UP & DOWN)G FR G (up & down) front acceleration sensor RH reading / min.: -1045.29 m/s2
max.: 1045.26 m/s20 +/-0.98 m/s2 at still condition Reading changes when vehicle (FR) is bounced (UP & DOWN)G FL G (up & down) front acceleration sensor LH reading / min.: -1045.29 m/s2
max.: 1045.26 m/s20 +/-0.98 m/s2 at still condition Reading changes when vehicle (FL) is bounced (UP & DOWN)G R G (up & down) rear acceleration sensor reading / min.:-1045.29 m/s2
max.: 1045.26 m/s20 +/-0.98 m/s2 at still condition Reading changes when vehicle (rear) is bounced (BACK & FORTH)G G sensor reading / min.: -4.5952 m/s2
max.: 4.5593 m/s20 +/-0.98 m/s2 at still condition Reading changes when vehicle is bounced FR HEIGHT Front height control sensor RH reading / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)- - FL HEIGHT Front height control sensor LH reading / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)- - RR HEIGHT Rear height control sensor RH reading / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)- - RL HEIGHT Rear height control sensor LH reading / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)- - HEIGHT MAX Display of amount of vehicle height calibration that is possible / min.: 0 mm
max.: 655.35 mm (25.8011 in)min.: 0 mm (0 in.)
max.: 20 mm (0.79 in.)- FR ADJUST Display of vehicle height offset recorded value of front right wheel / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)- - FL ADJUST Display of vehicle height offset recorded value of front left wheel / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)- - RR ADJUST Display of vehicle height offset recorded value of rear right wheel / min.:-3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)- - RL ADJUST Display of vehicle height offset recorded value of rear left wheel / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)- - FR AFTER ADJUST Display of after-calibration vehicle height value of front right wheel / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)When vehicle height normal: 0 +/-20 mm (0 +/- 0.79 in.)
When vehicle height is changing: Varies based on vehicle height
After HEIGHT HIGH adjustment: 20 +/- 20 mm (0.79 +/- 0.79 in.)- FL AFTER ADJUST Display of after-calibration vehicle height value of front left wheel / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)When vehicle height normal: 0 +/-20 mm (0 +/- 0.79 in.)
When vehicle height is changing: Varies based on vehicle height
After HEIGHT HIGH adjustment: 20 +/- 20 mm (0.79 +/- 0.79 in.)- RR AFTER ADJUST Display of after-calibration vehicle height value of rear right wheel / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)When vehicle height normal: 0 +/-20 mm (0 +/- 0.79 in.)
When vehicle height is changing: Varies based on vehicle height
After HEIGHT HIGH adjustment: 20 +/- 20 mm (0.79 +/- 0.79 in.)- RL AFTER ADJUST Display of after-calibration vehicle height value of rear left wheel / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)When vehicle height normal: 0 +/-20 mm (0 +/- 0.79 in.)
When vehicle height is changing: Varies based on vehicle height
After HEIGHT HIGH adjustment: 20 +/- 20 mm (0.79 +/- 0.79 in.)- STOP LIGHT SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released- COMFORT SW Absorber control switch ON or OFF ON: COMFORT
OFF: Normal- SPORT SW Absorber control switch ON or OFF ON: SPORT
OFF: Normal- DOOR SW Door switch / ON or OFF ON: Open a door
OFF: Close all doors- DAMPER SW 1 Height control switch / ON or OFF ON: Switch is pressed and held
OFF: Switch is not pressed- HEIGHT CTRL Vehicle height control condition reading / ON or OFF ON: Vehicle height control operating
OFF: Vehicle height control not operating- HEIGHT OFFSET Vehicle height offset calibration condition reading / ON or OFF ON: Vehicle height offset calibration complete
OFF: Before vehicle height offset calibration- HV READY - OFF - TD TD terminal / ON or OFF ON: Height control is not operating
OFF: Height control is operating- TC TC terminal / ON or OFF ON: DTC is output
OFF: DTC is not output- TS TS terminal / ON or OFF ON: During test mode
OFF: Normal mode- FR WHEEL SPD Front right wheel speed reading / min.: 0 km/h (0 mph)
max.: 255 km/h (159 mph)Actual vehicle speed Speed indicated on the combination meter FL WHEEL SPD Front left wheel speed reading / min.: 0 km/h (0 mph)
max.: 255 km/h (159 mph)Actual vehicle speed Speed indicated on the combination meter RR WHEEL SPD Rear right wheel speed reading / min.: 0 km/h (0mph)
max.: 255 km/h (159 mph)Actual vehicle speed Speed indicated on the combination meter RL WHEEL SPD Rear left wheel speed reading / min.: 0 km/h (0 mph)
max.: 255 km/h (159 mph)Actual vehicle speed Speed indicated on the combination meter IG VOLTAGE ECU power supply voltage / min.: 0 V
max.: 255 VActual ECU power supply voltage: 10 to 14 V - STEERING ANGLE Steering angle sensor reading / min.:-49152°
max. 49150.5°Actual steering angle Left turn: reading increases Right turn: reading decreases - ENGINE SPEED Cam position sensor reading / min.: 0 rpm
max.: 25,500 rpmActual engine speed Speed indicated on the combination meter DMPFR Damper step (Front RH) / min.: 0 step
max.: 255 stepmin.: 1 step max.: 17 step - DMP FL Damper step (Front LH) / min.: 0 step
max.: 255 stepmin.: 1 step max.: 17 step - DMP RR Damper step (Rear RH) / min.: 0 step
max.: 255 stepmin.: 1 step max.: 17 step - DMP RL Damper step (Rear LH) / min.: 0 step
max.: 255 stepmin.: 1 step max.: 17 step - MAX DMP STEP FR Damper step (Front LH) / min.: 0 step
max.: 255 step17 step - MAX DMP STEP FL Damper step (Front LH) / min.: 0 step
max.: 255 step17 step - MAX DMP STEP RR Damper step (Rear RH) / min.: 0 step
max.: 255 step17 step - MAX DMP STEP RL Damper step (Rear LH) / min.: 0 step
max.: 255 step17 step - #CODES Number of DTC recorded/ min.: 0
max.: 2550 - - Techstream
Air suspension
TECHSTREAM - AIR SUSPENSION SPECIFICATIONTester Display Measurement Item/Range Normal Condition Diagnostic Note (Up & Down)G Sensor FR G (up & down) front acceleration sensor RH reading / min.:-1045.29 m/s2
max.: 1045.26 m/s20 +/-0.98 m/s2 at still condition Reading changes when vehicle (FR) is bounced (Up & Down)G Sensor FL G (up & down) front acceleration sensor LH reading / min.:-1045.29 m/s2
max.: 1045.26 m/s20 +/-0.98 m/s2 at still condition Reading changes when vehicle (FL) is bounced (Up & Down)G Sensor Rear G (up & down) rear acceleration sensor reading / min.: -1045.29 m/s2
max.: 1045.26 m/s20 +/-0.98 m/s2 at still condition Reading changes when vehicle (rear) is bounced (Back & Forth)G Sensor G sensor reading / min.: -4.5952 m/s2
max.: 4.5593 m/s20 +/-0.98 m/s2 at still condition Reading changes when vehicle is bounced FR Height Control Sensor Front height control sensor RH reading / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)- - FL Height Control Sensor Front height control sensor LH reading / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)- - RR Height Control Sensor Rear height control sensor RH reading / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)- - RL Height Control Sensor Rear height control sensor LH reading / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)- - Height Offset Max Display of amount of vehicle height calibration that is possible / min.: 0 mm
max.: 655.35 mm (25.8011 in)min.: 0 mm (0 in.) max.: 20 mm (0.79 in.) - FR Height Adjust Display of vehicle height offset recorded value of front right wheel / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)- - FL Height Adjust Display of vehicle height offset recorded value of front left wheel / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)- - RR Height Adjust Display of vehicle height offset recorded value of rear right wheel / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)- - RL Height Adjust Display of vehicle height offset recorded value of rear left wheel / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)- - FR After Height Adjust Display of after-calibration vehicle height value of front right wheel / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)When vehicle height normal: 0 +/-20 mm (0 +/- 0.79 in.) When vehicle height is changing: Varies based on vehicle height After HEIGHT HIGH adjustment: 20 +/- 20 mm (0.79 +/- 0.79 in.) - FL After Height Adjust Display of after-calibration vehicle height value of front left wheel / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)When vehicle height normal: 0 +/-20 mm (0 +/- 0.79 in.) When vehicle height is changing: Varies based on vehicle height After HEIGHT HIGH adjustment: 20 +/- 20 mm (0.79 +/- 0.79 in.) - RR After Height Adjust Display of after-calibration vehicle height value of rear right wheel / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)When vehicle height normal: 0 +/-20 mm (0 +/- 0.79 in.) When vehicle height is changing: Varies based on vehicle height After HEIGHT HIGH adjustment: 20 +/- 20 mm (0.79 +/- 0.79 in.) - RL After Height Adjust Display of after-calibration vehicle height value of rear left wheel / min.: -3276.8 mm (-129 in.)
max.: 3276.7 mm (129 in.)When vehicle height normal: 0 +/-20 mm (0 +/- 0.79 in.) When vehicle height is changing: Varies based on vehicle height After HEIGHT HIGH adjustment: 20 +/- 20 mm (0.79 +/- 0.79 in.) - Stop Light Switch Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released- COMFORT Switch Absorber control switch ON or OFF ON: COMFORT
OFF: Normal- SPORT Switch Absorber control switch ON or OFF ON: SPORT
OFF: Normal- Door Switch Door switch / ON or OFF ON: Open a door
OFF: Close all doors- Damping Force Switch 1 Height control switch / ON or OFF ON: Switch is pressed and held
OFF: Switch is not pressed- Height Control Vehicle height control condition reading / ON or OFF ON: Vehicle height control operating
OFF: Vehicle height control not operating- Height Offset Vehicle height offset calibration condition reading / ON or OFF ON: Vehicle height offset calibration complete
OFF: Before vehicle height offset calibration- HV Ready - OFF - TD Terminal TD terminal / ON or OFF ON: Height control is not operating
OFF: Height control is operating- TC Terminal TC terminal / ON or OFF ON: DTC is output
OFF: DTC is not output- TS Terminal TS terminal / ON or OFF ON: During test mode
OFF: Normal mode- FR Wheel Speed Front right wheel speed reading / min.: 0 km/h (0 mph)
max.: 255 km/h (159 mph)Actual vehicle speed Speed indicated on the combination meter FL Wheel Speed Front left wheel speed reading / min.: 0 km/h (0 mph)
max.: 255 km/h (159 mph)Actual vehicle speed Speed indicated on the combination meter RR Wheel Speed Rear right wheel speed reading / min.: 0 km/h (0 mph)
max.: 255 km/h (159 mph)Actual vehicle speed Speed indicated on the combination meter RL Wheel Speed Rear left wheel speed reading / min.: 0 km/h (0 mph)
max.: 255 km/h (159 mph)Actual vehicle speed Speed indicated on the combination meter IG Power Source Voltage ECU power supply voltage / min.:0V
max.: 255 VActual ECU power supply voltage: 10 to 14 V - Steering Angle Steering angle sensor reading / min.: -49152°
max. 49150.5°Actual steering angle
Left turn: reading increases
Right turn: reading decreases- Engine Speed Cam position sensor reading / min.: 0 rpm
max.: 25,500 rpmActual engine speed Speed indicated on the combination meter Damper Step FR Damper step (Front RH) / min.: 0 step
max.: 255 stepmin.: 1 step
max.: 17 step- Damper Step FL Damper step (Front LH) / min.: 0 step
max.: 255 stepmin.: 1 step
max.: 17 step- Damper Step RR Damper step (Rear RH) / min.: 0 step
max.: 255 stepmin.: 1 step
max.: 17 step- Damper Step RL Damper step (Rear LH) / min.: 0 step
max.: 255 stepmin.: 1 step
max.: 17 step- Max Damper Step FR Damper step (Front LH) / min.: 0 step
max.: 255 step17 step - Max Damper Step FL Damper step (Front LH) / min.: 0 step
max.: 255 step17 step - Max Damper Step RR Damper step (Rear RH) / min.: 0 step
max.: 255 step17 step - Max Damper Step RL Damper step (Rear LH) / min.: 0 step
max.: 255 step17 step - Number of Trouble Codes Number of DTC recorded/ min.: 0
max.: 2550 -
- Intelligent tester
- Enter the following menus:
- Intelligent tester - Select: DIAGNOSIS / OBD/ MOBD / BODY / CENTER CONSOLE / DATA LIST/
- Techstream - Select: Body Electrical / Center Console Switch / Data List /
- Read the DATA LIST by following the directions on the tester screen.
- Intelligent tester
CENTER CONSOLE
INTELLIGENT TESTER - CENTER CONSOLE SPECIFICATIONTester Display Measurement Item/Range Normal Condn Diagnostic Note SPORT SW Absorber control switch ON or OFF ON: SPORT
OFF: Normal- COMFORT SW Absorber control switch ON or OFF ON: COMFORT
OFF: Normal- HEIGHT HIGH SW Height control switch / ON or OFF ON: Switch is pressed and held
OFF: Switch is not pressed- - Techstream
Center Console Switch
TECHSTREAM - CENTER CONSOLE SWITCH SPECIFICATIONTester Display Measurement Item/Range Normal Condn Diagnostic Note SPORT Mode Switch Absorber control switch ON or OFF ON: SPORT
OFF: Normal- COMFORT Mode Switch Absorber control switch ON or OFF ON: COMFORT
OFF: Normal- HEIGHT HIGH Switch Height control switch / ON or OFF ON: Switch is pressed and held
OFF: Switch is not pressed-
- Intelligent tester
- PERFORM ACTIVE TEST
HINT:
Using the Intelligent tester or Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
- Connect the Intelligent tester or Techstream to the DLC3.
- Turn the engine switch on (IG) and turn the tester ON.
- Enter the following menus:
- Intelligent tester - Select: DIAGNOSIS / OBD/ MOBD / CHASSIS / AIR SUSPENSION / ACTIVE TEST /
- Techstream - Select: Chassis / Air suspension / Active Test /
- Perform the ACTIVE TEST by following the prompts on the tester.
- Intelligent tester
AIR SUSPENSION
INTELLIGENT TESTER - AIR SUSPENSION SPECIFICATIONTester Display Test Part Control Range Diagnostic Note DAMPER FR Changes damper step (Front RH) / min.: 1 step
max.: 17 stepShock absorber hardens as damper step increases DAMPER FL Changes damper step (Front LH) / min.: 1 step
max.: 17 stepShock absorber hardens as damper step increases DAMPER RR Changes damper step (Rear RH) / min.: 1 step
max.: 17 stepShock absorber hardens as damper step increases DAMPER RL Changes damper step (Rear LH) / min.: 1 step
max.: 17 stepShock absorber hardens as damper step increases FR UP & DOWN Right front vehicle height / UP or DOWN - FL UP & DOWN Left front vehicle height / UP or DOWN - RR UP & DOWN Right rear vehicle height / UP or DOWN - RL UP & DOWN Left rear vehicle height / UP or DOWN - FR SOL Turn OFF front solenoid valve RH 1 second after turning it ON - Operation of solenoid (clicking sound) can be heard FL SOL Turn OFF front solenoid valve LH 1 second after turning it ON - Operation of solenoid (clicking sound) can be heard RR SOL Turn OFF rear solenoid valve RH 1 second after turning it ON - Operation of solenoid (clicking sound)can be heard RL SOL Turn OFF rear solenoid valve LH 1 second after turning it ON - Operation of solenoid (clicking sound) can be heard MOTOR RELAY Suspension control relay / ON or OFF Operation of solenoid (clicking sound) can be heard EXHAUST SOL Exhaust solenoid / ON or OFF Operation of solenoid (clicking sound)can be heard - Techstream
Air suspension
TECHSTREAM - AIR SUSPENSION SPECIFICATIONTester Display Test Part Control Range Diagnostic Note Damper Step FR Changes damper step (Front RH) / min.: 1 step
max.: 17 stepShock absorber hardens as damper step increases Damper Step FL Changes damper step (Front LH) / min.: 1 step
max.: 17 stepShock absorber hardens as damper step increases Damper Step RR Changes damper step (Rear RH) / min.: 1 step
max.: 17 stepShock absorber hardens as damper step increases Damper Step RL Changes damper step (Rear LH) / min.: 1 step
max.: 17 stepShock absorber hardens as damper step increases FR Wheel Up/Down Right front vehicle height / UP or DOWN - FL Wheel Up/Down Left front vehicle height / UP or DOWN - RR Wheel Up/Down Right rear vehicle height / UP or DOWN - RL Wheel Up/Down Left rear vehicle height / UP or DOWN - Front Right Solenoid Turn OFF front solenoid valve RH 1 second after turning it ON - Operation of solenoid (clicking sound)can be heard Front Left Solenoid Turn OFF front solenoid valve LH 1 second after turning it ON - Operation of solenoid (clicking sound) can be heard Rear Right Solenoid Turn OFF rear solenoid valve RH 1 second after turning it ON - Operation of solenoid (clicking sound) can be heard Rear Left Solenoid Turn OFF rear solenoid valve LH 1 second after turning it ON - Operation of solenoid (clicking sound) can be heard Motor Relay Suspension control relay / ON or OFF Operation of solenoid (clicking sound) can be heard Exhaust Solenoid Exhaust solenoid / ON or OFF Operation of solenoid (clicking sound) can be heard
- Intelligent tester
- Enter the following menus:
- Intelligent tester - Select: DIAGNOSIS / OBD/ MOBD / BODY / METER / ACTIVE TEST /
- Techstream - Select: Body Electrical / Combination Meter / Active Test /
- Perform the ACTIVE TEST by following the prompts on the tester.
- Intelligent tester
METER
INTELLIGENT TESTER - METER SPECIFICATIONTester Display Test Part Control Range Diagnostic Note TEMS SPORTS Absorber control indicator light (SPORT)/ ON or OFF - TEMS COMFORT Absorber control indicator light (COMFORT)/ ON or OFF - HEIGHT INDIC Height control indicator light (HEIGHT HIGH)/ ON or OFF - - Techstream
Combination Meter
TECHSTREAM - COMBINATION METER SPECIFICATIONTester Display Test Part Control Range Diagnostic Note Indicat. TEMS Sports Absorber control indicator light (SPORT)/ ON or OFF - Indicat. TEMS Comfort Absorber control indicator light (COMFORT)/ ON or OFF - Indicat. Height High Height control indicator light (HEIGHT HIGH)/ ON or OFF -
- Intelligent tester