Data List / Active Test

1. READ DATA LIST 

   HINT:

   Using the intelligent tester's DATA LIST allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the DATA LIST early in troubleshooting is one way to save time.

   1. Connect the intelligent tester (with CAN VIM) to the DLC3.
   2. Turn the ignition switch ON.
   3. Read the DATA LIST by following the directions on the tester screen.

   Power window control system 

   DATA LIST - POWER WINDOW CONTROL SYSTEM
   
   

   Item	Measurement Item / Display (Range)	Normal Condition	Diagnostic Note
   P/W AUTO SW	Driver side power window auto up/down switch / ON or OFF	ON: Driver side door P/W auto switch is ON position OFF: Driver side door P/W auto switch is OFF position	-
   P P/W AUTO SW	Front passenger side power window auto up/down switch/ ON or OFF	ON: Front passenger side door remote P/W auto switch is ON position OFF: Front passenger side door remote P/W auto switch is OFF position	-
   RR P/W AUTO SW	Rear power window RH auto up/ down switch/ ON or OFF	ON: Rear door RH remote P/W auto switch is ON position OFF: Rear door RH remote P/W auto switch is OFF position	-
   RL P/W AUTO SW	Rear power window LH auto up/ down switch/ ON or OFF	ON: Rear door LH P/W auto switch is ON position OFF: Rear door LH P/W auto switch is OFF position	-
   LIMIT SW	Jam protection limit switch / ON or OFF	ON: Jam protection limit switch is ON position OFF: Jam protection limit switch is OFF position	-
   LOCK POS SW	Power window lock switch / ON or OFF	ON: Door unlock detection switch is ON position OFF: Door unlock detection switch is OFF position	-
   GLASS POS-1/4	Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open position / OK or CAUTION	OK Margin is sufficient during manual UP operation: CAUTION: May be displayed even when no resistance is applied in either position. In this case there is a foreign object stuck in that position	-
   GLASS POS-2/4	Margin for jam protection triggering force of window glass within range of fully closed to 1/2 open position / OK or CAUTION	OK: Margin is sufficient during manual UP operation CAUTION: May be displayed even when no resistance is applied in either position. In this case there is a foreign object stuck in that position	-
   GLASS POS-3/4	Margin for jam protection triggering force of window glass within range of fully closed to 3/4 open position / OK or CAUTION	OK: Margin is sufficient during manual UP operation: CAUTION: May be displayed even when no resistance is applied in either position. In this case there is a foreign object stuck in that position	-
   GLASS POS-OPEN	Margin for jam protection triggering force of window glass within range of fully closed to 3/4 to fully open position / OK or CAUTION	OK: Margin is sufficient during manual UP operation CAUTION: May be displayed even when no resistance is applied in either position. In this case there is a foreign object stuck in that position	-
   UP/DOOR KEY	Make all door windows go up manually by holding driver's side door key to lock side for 1.5 seconds when ignition switch is OFF / NOT AVL or AVAIL	NOT AVL: Function is not available AVAIL: Function is available	-
   DOWN/DOOR KEY	Make all door windows go down manually by holding driver's side door key to lock side for 1.5 seconds when ignition switch is OFF / NOT AVL or AVAIL	NOT AVL: Function is not available AVAIL: Function is available	-

2. PERFORM ACTIVE TEST 

   HINT:

   Perform the intelligent tester's ACTIVE TEST allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the ACTIVE TEST early in troubleshooting is one way to save time. The DATA LIST can be displayed during the ACTIVE TEST.

   1. Connect the intelligent tester (with CAN VIM) to the DLC3.
   2. Turn the ignition switch ON.
   3. Perform the ACTIVE TEST by following the directions on the tester screen.

Power window control system