Diagnostic Trouble Code Table
HINT:
If a trouble code is displayed during the DTC check, check the circuit indicated by the DTC. For details of each code, refer to the information in the DTC table.
DTC table of ABS:
DTC TABLE OF ABS
| DTC No. | Detection Item | Trouble Area |
|---|---|---|
| C0200/31 | Right Front Wheel Speed Sensor Signal |
|
| C0205/32 | Front Speed Sensor LH Circuit |
|
| C0210/33 | Right Rear Wheel Speed Sensor Signal |
|
| C0215/34 | Rear Speed Sensor LH Circuit |
|
| C0226/21 | SFR Solenoid Circuit |
|
| C0236/22 | SFL Solenoid Circuit |
|
| C0246/23 | SRR Solenoid Circuit |
|
| C0256/24 | SRL Solenoid Circuit |
|
| C0273/13 | Open in ABS Motor Relay Circuit |
|
| C0274/14 | Short to B+ in ABS Motor Relay Circuit |
|
| C0278/11 | Open in ABS Solenoid Relay Circuit |
|
| C0279/12 | Short to B+ in ABS Solenoid Relay Circuit |
|
| C1225/25 | SM Solenoid Circuit |
|
| C1235/35 | Foreign Object is Attached on Tip of Front Speed Sensor RH |
|
| C1236/36 | Foreign Object is Attached on Tip of Front Speed Sensor LH |
|
| C1238/38 | Foreign Object is Attached on Tip of Rear Speed Sensor RH |
|
| C1239/39 | Foreign Object is Attached on Tip of Rear Speed Sensor LH |
|
| C1241/41 | Low Battery Positive Voltage |
|
| C1243/43 | Acceleration Sensor Stuck Malfunction |
|
| C1244/44 | Open or Short in Deceleration Sensor Circuit |
|
| C1245/45 | Acceleration Sensor Output Malfunction |
|
| C1246/46 | Master Cylinder Pressure Sensor Malfunction |
|
| C1249/49 | Open in Stop Light Switch Circuit |
|
| C1251/51 | Open in Pump Motor Circuit |
|
| C1267/67 | Brake Pedal Load Sensing Switch |
|
| C1337/37 | Different Diameter Tire Malfunction |
|
| C1361/91 | Short Circuit in ABS Motor Fail Safe Relay Circuit |
|
| C1381/97 | Yaw Rate and / or Acceleration Sensor Power Supply Voltage Malfunction |
|
| U0073/94 | Control Module Communication Bus OFF | CAN communication system |
| U0124/95 | Lost Communication with Lateral Acceleration Sensor Module | CAN communication system (Skid control ECU to yaw rate sensor and acceleration sensor) |
*1, *2:
Even after the trouble areas are repaired, the ABS warning light will not go off unless the following operations are performed.
- *1:
- Drive the vehicle at 12 mph (20 km/h) for 30 seconds or more and check that the ABS warning light goes off.
- Clear the DTC.
- *2:
- Keep the vehicle in a stationary condition for 5 seconds or more and depress the brake pedal lightly 2 or 3 times.
- Drive the vehicle at a speed of 31 mph (50 km/h). Then depress the brake pedal strongly for approximately 3 seconds.
- Repeat the above operation 3 times or more and check that the ABS warning light goes off.
- Clear the DTC.
HINT:
- In some cases, the intelligent tester cannot be used when the ABS warning light remains on.
- If any of U0073/94 and U0124/95 are displayed, inspect the CAN communication system.
DTC table of VSC:
DTC TABLEDTC No. Detection Item Trouble Area C1201/51 Engine Control System Malfunction Engine control system C1203/53 ECM Communication Circuit Malfunction ECM C1210/36 Zero Point Calibration of Yaw Rate Sensor Undone - Yaw rate and acceleration sensor
- Zero point calibration undone
C1223/43 ABS Control System Malfunction ABS control system C1231/31 Steering Angle Sensor Circuit Malfunction - Steering angle sensor
- Steering angle sensor circuit
- +B circuit
C1232/32 Stuck in Deceleration Sensor - Yaw rate and acceleration sensor
- Yaw rate and acceleration sensor circuit
C1234/34 Yaw Rate Sensor Malfunction - Yaw rate and acceleration sensor
- Yaw rate and acceleration sensor circuit
C1290/66 Steering Angle Sensor Zero Point Malfunction - Yaw rate and acceleration sensor zero point calibration incomplete
- Poor adjustment of the centered position of the steering wheel
- Poor adjustment of front wheel alignment
C1336/39 Zero Point Calibration of Acceleration Sensor Undone - Acceleration sensor
- Zero point calibration undone
U0100/65 Lost Communication with ECM/PCM CAN communication system (Skid control ECU to ECM) U0123/62 Lost Communication with Yaw Rate Sensor Module CAN communication system (Skid control ECU to yaw rate sensor and acceleration sensor) U0126/63 Lost Communication with Steering Angle Sensor Module CAN communication system (Skid control ECU to steering angle sensor) HINT:
- In some cases, the intelligent tester cannot be used when the VSC warning light remains on.
- If any of U0100/65, U0123/62 and U0126/63 are displayed, inspect the CAN communication system.
Test Mode DTC of ABS:
TEST MODE DTC OF ABSDTC No. Detection Item Trouble Area C1271/71 Low Output Signal of Front Speed Sensor RH (Test Mode DTC) - Front speed sensor RH
- Sensor installation
- Speed sensor rotor
C1272/72 Low Output Signal of Front Speed Sensor LH (Test Mode DTC) - Front speed sensor LH
- Sensor installation
- Speed sensor rotor
C1273/73 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC) - Rear speed sensor RH
- Sensor installation
- Speed sensor rotor
C1274/74 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) - Rear speed sensor LH
- Sensor installation
- Speed sensor rotor
C1275/75 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) Speed sensor rotor C1276/76 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) Speed sensor rotor C1277/77 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) Speed sensor rotor C1278/78 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) Speed sensor rotor C1279/79 Acceleration Sensor Output Voltage Malfunction (Test Mode DTC) - Yaw rate and acceleration sensor
- Sensor installation
C1281/81 Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC) - Stop light switch
- Brake pedal load sensing switch
- Master cylinder pressure sensor
Test Mode DTC of VSC:
TEST MODE DTC OF VSCDTC No. Detection Item Trouble Area C0371/71 Yaw Rate Sensor (Test Mode DTC) Yaw rate and acceleration sensor