Data List / Active Test
- DATA LIST
HINT:
With the intelligent tester connected to the DLC3 and the ignition switch ON, the Electronically Controlled Brake, ABS, and VSC data list can be displayed. Follow the prompts on the tester screen to access the DATA LIST.
ABS / VSC / TRAC:
DATA LISTTester Display Measurement Item/Range Normal Condition Diagnostic Note ECB(1) MTR RELAY ABS motor relay / ON or OFF ON: Motor relay ON
OFF: Motor relay OFF- IDLE SW Main idle switch / ON or OFF ON: Accelerator pedal released
OFF: Accelerator pedal depressed- STOP LAMP SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released- PARKING BRAKE SW Parking brake switch / ON or OFF ON: Parking brake applied
OFF: Parking brake released- LEVER POSITION Shift lever position information / P/N, R, D/M, 1st-6th/B, FAIL - - FR WHEEL SPD Wheel speed sensor (FR) reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h) Actual wheel speed Similar speed as indicated on speedometer FL WHEEL SPD Wheel speed sensor (FL) reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h) Actual wheel speed Similar speed as indicated on speedometer RR WHEEL SPD Wheel speed sensor (RR) reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h) Actual wheel speed Similar speed as indicated on speedometer RL WHEEL SPD Wheel speed sensor (RL) reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h) Actual wheel speed Similar speed as indicated on speedometer DECELERAT SEN Deceleration sensor 1 reading / min.: -18.52 m/s2 , max.: -18.33 m/s2 Approximately m/s2 while stationary Reading changes when vehicle is bounced DECELERAT SEN 2 Deceleration sensor 2 reading / min.: -18.52 m/s2 , max.: -18.33 m/s2 Approximately m/s2 while stationary Reading changes when vehicle is bounced FR SPD OPN FR speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- FL SPD OPN FL speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- RR SPD OPN RR speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- RL SPD OPN RL speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- YAW RATE OPN Yaw rate sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- DECELERAT OPN Deceleration sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- STEERING OPN Steering angle sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- M/C OPN Master cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- ABS WARN LAMP ABS warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- BRAKE WARN LAMP BRAKE warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- SLIP INDI LAMP SLIP indicator light / ON or OFF ON: Indicator light ON
OFF: Indicator light OFF- BUZZER Skid control buzzer / ON or OFF ON: Buzzer ON
OFF: Buzzer OFF- VSC WARN LAMP VSC warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- VEHICLE SPD Maximum wheel speed sensor reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h) Actual vehicle speed Speed indicated on speedometer FR WHEEL ACCEL FR wheel acceleration / min.: -200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2
Max.: 199.27 m/s2- FL WHEEL ACCEL FL wheel acceleration / min.: -200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2
Max.: 199.27 m/s2- RR WHEEL ACCEL RR wheel acceleration / min.: -200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2
Max.: 199.27 m/s2- RL WHEEL ACCEL RL wheel acceleration / min.: -200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2
Max.: 199.27 m/s2- ZERO DECELERAT Memorized zero value / min.: -25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2
Max.: 24.91 m/s2- ZERO DECELERAT 2 Memorized zero value / min.: -25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2
Max.: 24.91 m/s2- ZERO STEERING Memorized zero value / min.: -3276.8 deg, max.: 3276.7 deg Min.: -3276.8 deg
Max.: 3276.7 deg- LATERAL G Lateral G/min.:-25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2
Max.: 24.91 m/s2- FORWARD & REA G Forward and rearward G / min.: -25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2
Max.: 24.91 m/s2- YAW RATE VALUE Yaw rate value / min.: -128 deg/s, max.: 127 deg/s Min.: -128 deg/s
Max.: 127 deg/s- STEERING ANGLE Steering angle value / min.: -3276.8 deg, max.: 3276.7 deg Min.: -3276.8 deg
Max.: 3276.7 deg- TRAC STATUS TRAC control status / ON or OFF ON: During the control - TRAC BRK STATUS TRAC brake control status / ON or OFF ON: During the control - FR VSC STATUS FR wheel VSC control status / ON or OFF ON: During the control - FL VSC STATUS FL wheel VSC control status / ON or OFF ON: During the control - RR VSC STATUS RR wheel VSC control status / ON or OFF ON: During the control - RL VSC STATUS RL wheel VSC control status / ON or OFF ON: During the control - YAW RATE SENS 1 Yaw rate sensor 1 / min.: -128 deg/s, max.: 127 deg/s Min.: -128 deg/s
Max.: 127 deg/s- YAW RATE SENS 2 Yaw rate sensor 2 / min.: -128 deg/s, max.: 127 deg/s Min.: -128 deg/s
Max.: 127 deg/s- ZERO YAW RATE Memorized zero value / min.: -128 deg/s, max.: 127 deg/s Min.: -128 deg/s
Max.: 127 deg/s- ZERO YAW RATE 2 Memorized zero value / min.: -128 deg/s, max.: 127 deg/s Min.: -128 deg/s
Max.: 127 deg/s- STEERING SEN Steering angle sensor/ min.: -3276.8 deg, max.: 3276.7 deg Left turn: Increase
Right turn: Decrease- MAS CYL PRESS 1 Master cylinder pressure sensor 1 reading / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V Reading increases when brake pedal is depressed MAS CYL PRESS 2 Master cylinder pressure sensor 2 reading / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V Reading increases when brake pedal is depressed FR ABS STATUS FR wheel ABS control status / ON or OFF ON: During the control - FLABS STATUS FL Wheel ABS control status / ON or OFF ON: During the control - RR ABS STATUS RR wheel ABS control status / ON or OFF ON: During the control - RL ABS STATUS RL wheel ABS control status / ON or OFF ON: During the control - BA STATUS BA control status / ON or OFF ON: During the control - PBA STATUS PBA control status / ON or OFF ON: During the control - INSPECTION MODE Inspection mode / OTHER or INSPECT - - #IG ON2 Number of IG ON after entering the inspection mode / min.: 0, max.: 255 - - PEDAL STROKE Stroke sensor / min.: 0 V, max.: 5 V When brake pedal is released: 0.7 to 1.3 V - PEDAL STROKE 2 Stroke sensor 2 / min.: 0 V, max.: 5V When brake pedal is released: 3.7 to 4.3 V - ACC PRESS SENS Accumulator pressure sensor / min.: 0 V, max.: 5 V Specified value: 3.2 to 4.0 V - FR W/C SENS FR wheel cylinder pressure sensor / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V - FLW/CSENS FL wheel cylinder pressure sensor / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V - RR W/C SENS RR wheel cylinder pressure sensor / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V - RL W/C SENS RL wheel cylinder pressure sensor / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V - RESERVOIR SW Brake fluid level warning switch / ON or OFF ON: Reservoir level normal
OFF: Reservoir level low- ECB* WARN LAMP Brake control warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- FR RQST TORQ Front regenerative request torque / min.: 0 N*m, max.: 4,080 N*m - - FR OPERATE TORQ Front regenerative operation torque / min.: 0 N*m, max.: 4,080 N*m - - RR RQST TORQ Rear regenerative request torque / min.: 0 N*m, max.: 4,080 N*m - - RR OPERATE TORQ Rear regenerative operation torque / min.: 0 N*m, max.: 4,080 N*m - - REGEN COOP Regenerative cooperation / ON or OFF ON: Operate
OFF: Not operate- ECB* MTR RELAY 2 ABS motor relay 2 / ON or OFF ON: Motor relay ON
OFF: Motor relay OFF- ECB* RELAY ABS main relay / ON or OFF ON: Main relay ON
OFF: Main relay OFF- ECB* RELAY 2 ABS main relay 2 /ON or OFF ON: Main relay ON
OFF: Main relay OFF- VOLT M/C SEN Voltage of master cylinder pressure sensor / min.: -2.5 V, max.: 2.49 V - - VOLT M/C SEN 2 Voltage of master cylinder pressure sensor 2 / min.: -2.5 V, max.: 2.49 V - - VOLT STROK SEN Voltage of stroke sensor / min.: -2.5 V, max.: 2.49 V - - VOLT STROK SEN 2 Voltage of stroke sensor 2 / min.: -2.5 V, max.: 2.49 V - - SLAFR CUR SLAFR solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLAFL CUR SLAFL solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLARR CUR SLARR solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLARL CUR SLARL solenoid current/ min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLRFR CUR SLRFR solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLRFL CUR SLRFL solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLRRR CUR SLRRR solenoid current/ min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLRRL CUR SLRRL solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - M/C2 OPN Master cylinder pressure sensor 2 open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- STROKE OPN Stroke sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- FR W/C OPN FR wheel cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- FL W/C OPN FL wheel cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- RR W/C OPN RR wheel cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- RL W/C OPN RL wheel cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- ACC OPN Accumulator pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- SMC1 Master cut solenoid (SMC1) / ON or OFF ON: Operate
OFF: Not operate- SMC2 Master cut solenoid (SMC2) / ON or OFF ON: Operate
OFF: Not operate- SCSS Stroke simulator solenoid (SCSS) / ON or OFF ON: Operate
OFF: Not operate- # DTC Number of DTC recorded / min.: 0, max.: 255 - - (1) Electronically Controlled Brake - ACTIVE TEST
HINT:
Performing the ACTIVE TEST using the intelligent tester allows the relay, actuator, etc. to operate without removing any parts. Performing the ACTIVE TEST as the first step of troubleshooting is one of the methods to shorten labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch on.
- According to the display on the tester, perform the "ACTIVE TEST".
HINT:
The ignition switch must be turned to the ON position to proceed to the ACTIVE TEST using the intelligent tester.
ABS / VSC / TRAC:
ACTIVE TESTTester Display Test Part Control Range Diagnostic Note ABS WARN LAMP ABS warning light Warning light ON/OFF Observe combination meter VSC WARN LAMP VSC warning in multi information display Display ON/OFF Observe combination meter BRAKE WARN LAMP BRAKE warning light Warning light ON/OFF Observe combination meter SLIP INDI LAMP SLIP indicator light Indicator light ON/OFF Observe combination meter ECB* WARN LAMP Brake control warning light Warning light ON/OFF Observe combination meter BUZZER Skid control buzzer Buzzer ON/OFF Buzzer can be heard STP LAMP RELAY Stop light operation relay Relay ON/OFF Observe rear combination light (stop light) (Does not come on for 5 sec. or more) ECB* RELAY ABS No.1 relay Relay ON/OFF Operating sound of relay (clicking sound) can be heard ECB* RELAY 2 ABS No.2 relay Relay ON/OFF Operating sound of relay (clicking sound) can be heard ECB* MTR RELAY ABS MTR1 motor relay Relay ON/OFF Operating sound of relay (clicking sound) can be heard ECB(1) MTR RELAY 2 ABS MTR2 relay Relay ON/OFF Operating sound of relay (clicking sound) can be heard SMC1 Master cut solenoid (SMC1) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard SMC2 Master cut solenoid (SMC2) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard SCSS Stroke simulator solenoid (SCSS) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard (1) Electronically Controlled Brake