Shift Lever Position Sensor: Installation

1. Install the park/neutral position switch to the manual valve shaft.
2. Temporarily install the 2 bolts.
   Fig 1: Locating Shift Lever Position Sensor Bolts

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Place new lock plate and tighten the nut.

   Torque: 6.9 N*m (70 kgf*cm, 61 in.*lbf) 

   Fig 2: Identifying Lock Plate And Lock Nut

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Temporarily install the control shaft lever.
5. Turn the lever counterclockwise until it stops, then turn it clockwise 2 notches.
Fig 3: Identifying Control Shaft Lever
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Remove the control shaft lever.
7. Align the protruding part with the neutral basic line.
   NOTE: There is play on the nut stopper side (protruding part). Align the center point of the range of the play with the neutral basic line.
   Fig 4: Aligning Protruding Part With Neutral Basic Line

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
8. Tighten the 2 bolts in the order shown in the illustration.

   Torque: 13 N*m (133 kgf*cm, 10 ft.*lbf) 

   Fig 5: Locating Park/Neutral Position Switch Bolts

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
9. Using a screwdriver, stake the nut with the lock plate.
   Fig 6: Identifying Lock Plate

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
10. Install the control shaft lever, washer and nut.

    Torque: 6.9 N*m (70 kgf*cm, 61 in.*lbf) 

    Fig 7: Locating Control Shaft Lever

    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Move the shift lever to the N position.
2. Install a new clip to the control bracket.
3. Install the control cable to the control bracket.
   NOTE:

   • Make sure that the A claws on the clip are securely fit into the bracket holes.
   • Make sure that the cable is securely installed inside of the B claws of the clip.
   Fig 8: Identifying Control Cable

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Connect the park/neutral position switch connector.
Fig 9: Locating Park/Neutral Position Switch Connector
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Move the control shaft lever to the N position.
6. Temporarily install the control cable to the control shaft lever with the nut.
   Fig 10: Locating Control Cable

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
7. Lightly push up the control cable end.
   NOTE: Do not push the control cable end excessively.
   Fig 11: Pushing Up Control Cable End

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
8. Release your hand from the control cable end and then fully tighten the nut.

   Torque: 15 N*m (150 kgf*cm, 11 ft.*lbf) 

1. Using SST and a wrench, tighten the 2 new oil cooler tubes.

   SST 09023-12701 

   Torque: 34 N*m (350 kgf*cm, 25 ft.*lbf) 

   Fig 12: Locating Oil Cooler Tube

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the oil cooler tube to the control cable bracket with the bolt.

   Torque: 8.2 N*m (84 kgf*cm, 73 in.*lbf) 

   Fig 13: Locating Oil Cooler Hoses

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the oil cooler hoses to the oil cooler tubes.

(See INITIALIZATION )