LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2008 >> LS 460 >> Repair and Diagnosis >> External Pages >> Different car >> Section 51 (Smart Key System (Keyless Entry) (Diagnostics - Introduction)) >> Smart Key System >> Data List / Active Test >> Data List / Active Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test

WARNING: This page is about a different car, the 2011 Toyota Avalon. However, it is still accessible from the selected car via links, so may be relevant.
  1. DATA LIST 

    HINT: 

    By accessing the Data List displayed on Techstream, you can perform such functions as reading the values of switches and sensors without removing any parts. Reading the Data List is the first step of troubleshooting and is one method to shorten labor time.

    1. Connect Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Following the display on the tester, select "Data List".
      POWER SOURCE CONTROL ECU:

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Shift P Signal Status of shift P position switch / ON or OFF ON: Shift lever is P position
      OFF: Shift lever is non-P position      		 -
      Steering Unlock Switch Status of steering unlock switch / ON or OFF ON: Steering unlock switch is UNLOCK
      OFF: Steering unlock switch is LOCK      		 -
      Stop Light Switch 1 Status of stop light switch1 / ON or OFF ON: Brake pedal pressed
      OFF: Brake pedal depressed      		 -
      Start Switch 1 Status of start switch1 / ON or OFF ON: Engine switch is ON (IG)
      OFF: Engine switch is OFF      		 -
      Start Switch 2 Status of start switch2 / ON or OFF ON: Engine switch is ON (IG)
      OFF: Engine switch is OFF      		 -
      Neutral SW/Clutch SW Status of Neutral SW / ON or OFF ON: Shift lever is N position
      OFF: Shift lever is non-N position      		 -
      Latch Circuit Status of latch circuit / ON or OFF ON: Engine switch is ON (IG)
      OFF: Engine switch is OFF or ON (ACC) or ENGINE START      		 -
      IG1 Relay Monitor (Outside) Status of ignition1 relay monitor (outside) / ON or OFF ON: Engine switch is ON (IG)
      OFF: Engine switch is OFF      		 -
      IG1 Relay Monitor (Inside) Status of ignition1 relay monitor (inside) / ON or OFF ON: Engine switch is ON (IG)
      OFF: Engine switch is OFF      		 -
      IG2 Relay Monitor (Outside) Status of ignition2 relay monitor (outside) / ON or OFF ON: Engine switch is ON (IG)
      OFF: Engine switch is OFF      		 -
      IG2 Relay Monitor (Inside) Status of ignition2 relay monitor (inside) / ON or OFF ON: Engine switch is ON (IG)
      OFF: Engine switch is OFF      		 -
      Starter Relay Monitor Status of starter relay monitor / ON or OFF ON: ST relay is ON
      OFF: ST relay is OFF      		 -
      Stater Request Signal Status of starter requesting signal monitor / ON or OFF ON: ST relay is ON
      OFF: ST relay is OFF      		 -
      ACC Relay Monitor Status of ACC relay monitor / ON or OFF ON: Engine switch is ON (ACC)
      OFF: Engine switch is OFF      		 -
      ACC Relay Cut Signal Status of ACC relay cut signal / ON or OFF ON: Engine switch is OFF
      OFF: Engine switch is ON (ACC)      		 -
      Vehicle Speed Signal Status of vehicle speed signal / STOP or RUN ON: Vehicle is stopped
      OFF: Vehicle is running      		 -
      Engine Condition Status of engine condition / STOP or RUN ON: Engine is stopped
      OFF: Engine is running      		 When engine condition is rotating
      Power Supply Condition Status of power supply condition / ALL, ACC ON, IG1, IG2, ST ON ALL: All relay is ON
      ACC ON: ACC relay is ON
      IG1: IG1 relay is ON
      IG2: IG2 relay is ON
      ST ON: ST relay is ON      		 When ready signal allows to be capable driving
      #Code Status of Number of diagnosis codes / Min.: 0, Max.: 255 - -
      CERTIFICATION ECU:

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      D-Door Touch Sensor Status of touch sensor front LH / ON or OFF ON: Touch sensor is touched
      OFF: Touch sensor does not touched      		 -
      P-Door Touch Sensor Status of touch sensor front RH / ON or OFF ON: Touch sensor is touched
      OFF: Touch sensor does not touched      		 -
      Dr-Door Touch Sensor Status of touch sensor rear LH / ON or OFF ON: Touch sensor is touched
      OFF: Touch sensor does not touched      		 -
      Pr-Door Touch Sensor Status of touch sensor rear RH / ON or OFF ON: Touch sensor is touched
      OFF: Touch sensor does not touched      		 -
      D-Door Trigger Switch Lock switch front LH / ON or OFF ON: Lock switch is pushed
      OFF: Lock switch is not pushed      		 -
      P-Door Trigger Switch Lock switch front RH / ON or OFF ON: Lock switch is pushed
      OFF: Lock switch is not pushed      		 -
      Dr-Door Trigger Switch Lock switch rear LH / ON or OFF ON: Lock switch is pushed
      OFF: Lock switch is not pushed      		 -
      Pr-Door Trigger Switch Lock switch rear RH / ON or OFF ON: Lock switch is pushed
      OFF: Lock switch is not pushed      		 -
      TR/B-Door Unlock SW Luggage compartment open switch condition / ON or OFF ON: Luggage compartment open switch is pushed
      OFF: Luggage compartment open switch does not pushed      		 -
      IG SW Engine switch IG condition / ON or OFF ON: Engine switch ON (IG)
      OFF: Engine switch OFF      		 -
      ACC SW Engine switch ACC condition / ON or OFF ON: Engine switch ON (ACC)
      OFF: Engine switch OFF      		 -
      Ignition Available Area Ignition available area / FRONT or ALL Customization status is displayed -
      Parking Wait Time Parking wait time / 0.5s, 1.5s, 2.5s, 5s Customization status is displayed -
      Trunk Open Mode Luggage compartment door open mode with vehicle locked / ON or OFF Customization status is displayed -
      Key Lo-batt Wrn Low key battery warning / ON or OFF Customization status is displayed -
      Unmatched Vehicle-ID No communication condition between vehicle and electrical key transmitter (vehicle-ID) / YES or NO YES: Key ID does not match vehicle
      NO: Key ID matches vehicle      		 -
      No Response No Communication condition between vehicle and electrical key transmitter (response) / Yes or No Yes: Key ID code not matched to vehicle
      No: Key ID code matched to vehicle      		 -
      Unmatch Code Form No communication condition between vehicle and electrical key transmitter (response code and format) / YES or NO YES: Key ID code does not match
      NO: Key ID code matches      		 -
      Key Low Battery Key low battery / YES or NO YES: Key battery voltage drops
      NO: Key battery voltage is normal      		 -
      ID Code Different (Resp) No communication condition between vehicle and electrical key transmitter (ID code) / YES or NO YES: Key ID code does not match
      NO: Key ID code matches      		 -
      C Code Different No communication condition between vehicle and electrical key transmitter (challenge code) / YES or NO YES: Key ID code does not match
      NO: Key ID code matches      		 -
      P/S 10-Min Power save counter 10 minutes / Min.: 0, Max.: 255 The number of power saved for 10 minutes is displayed -
      P/S 5-Day Power save counter 5 days / Min.: 0, Max.: 255 The number of power saved for 5 days is displayed -
      P/S 14-Day Power save counter 14 days / Min.: 0, Max.: 255 The number of power saved for 10 days is displayed -
      ID Code Different No communication condition between vehicle and electrical key transmitter (ID code) / YES or NO YES: Key ID code does not match
      NO: Key ID code matches      		 -
      Different Rolling Code No communication condition between vehicle and electrical key transmitter (rolling code) / YES or NO YES: Key rolling code does not match
      NO: Key rolling code matches      		 -
      Door Unlock Mod Door unlock mode / ALL, EACH, D_DOOR, SIDE Mode status is displayed -
      Auto Entry Cancel SW Entry door lock function cancel / ON or OFF Mode status is displayed -
      Permit (Start) PERMIT(START) / NG or OK NG: Engine start without permission
      OK: Engine start permission      		 -
      Immobilizer Immobilizer function status / SET or UNSET SET: The key is not inside the cabin
      UNSET: Push the engine switch with the key inside the cabin with depressing the brake pedal      		 -
      Master Key Master key / MATCH or NO MATCH MATCH: Key code is sent
      NO MATCH: Unmatched key code      		 -
      Sub Key Sub key / MATCH or NO MATCH MATCH: Key code is sent
      NO MATCH: Unmatched key code      		 -
      BCC Malfunction BCC malfunction / NG or OK NG: Correct data sensing
      OK: Incorrect data sensing      		 -
      Abnormal Status Abnormal status / NG or OK NG: Malfunction
      OK: Normal      		 -
      Different Encrypt Code Different encrypt code / NG or OK NG: Data error
      OK: Normal      		 -
      Different Serial Number Different serial number / NG or OK NG: Data error
      OK: Normal      		 -
      Frame Error Frame error / NG or OK NG: Data error
      OK: Normal      		 -
      Response Response / NG or OK NG: With no response
      OK: Those with a response      		 -
      Wireless Com ID Wireless starter communication ID / Registered or No registered - -
      Wireless C-Code Wireless C code / Registered or No registered - -
      Steering Lock Sleep Cond Steering lock sleep condition / YES or NO - -
      Steering lock Start Cond Steering lock start condition / YES or NO - -
      Steering Lock Steering lock / SET or UNSET - This status changes depending on the state of some sensors.
      Steering Unlock Steering unlock / SET or UNSET - This status changes depending on the state of some sensors.
      Engine Start Condition Engine start condition / OK or NG OK: Engine start permission
      NG: Engine start without permission      		 -
      Sensor Value Sensor malfunction / NG (PAST) or OK NG (PAST): Sensor malfunction
      OK: No malfunction      		 -
      Power Supply Short Short in ECU / NG (PAST) or OK NG (PAST): Short in ECU
      OK: No malfunction      		 -
      Power Supply Open Open in ECU / NG (PAST) or OK NG (PAST): Open in ECU
      OK: No malfunction      		 -
      Motor Driver Shrt Short in driver ECU / NG (PAST) or OK NG (PAST): Short in driver ECU
      OK: No malfunction      		 -
      Motor Driver Open Open in driver ECU / NG (PAST) or OK NG (PAST): Open in driver ECU
      OK: No malfunction      		 -
      Lock/Unlock Receive Steering lock command reception record / YES or NO YES: Steering lock / unlock signal received
      NO: Steering lock / unlock signal not received      		 -
      Lock Bar Stuck Error Lock bar stuck malfunction / NG (PAST) or OK NG (PAST): Lock bar stuck malfunction
      OK: No malfunction      		 -
      Push Start Err Push button start function malfunction / NG (PAST) or OK NG (PAST): Malfunction in push button start
      OK: No malfunction      		 -
      IG2 Status IG2 status / ON or OFF ON: 10 to 14 V
      OFF: Below 1 V      		 -
      IG (Lin) LIN bus start-up status / ON or OFF ON: LIN bus started-up
      OFF: LIN bus not started-up      		 -
      ID-BOX Sleep Condition ID code box sleep condition / YES or NO YES: ID code box sleep available
      NO: ID code box sleep not available      		 -
      ID-BOX Start Condition ID code box start condition / YES or NO YES: ID code box started-up
      NO: ID code box not started-up      		 -
      EFI Code Receive EFI code receive / NG or OK NG: EFI code does not receive
      OK: EFI code received      		 -
      Engine Start Request ID code box start request condition / YES or NO YES: ID code box start request condition
      NO: ID code box non-start request condition      		 -
      3bit Code Request 3 bit code request / NG or OK NG: 3 bit code does not receive
      OK: 3 bit code received      		 -
      S Code Check Code verification result / OK or NG OK: Verification confirmed
      NG: Verification not conformed      		 -
      L Code Check Code verification result / OK or NG OK: Verification confirmed
      NG: Verification not conformed      		 -
      Unlock Request Receive Steering unlock request / YES or NO YES: Steering unlock
      NO: Steering lock      		 -
      Lock Request Receive Steering lock request / YES or NO YES / NO -
      Engine Start Request (Past) Engine start request / YES or NO YES / NO -
      EFI Communication EFI communication / OK or NG NG: EFI code does not receive
      OK: EFI code received      		 -
      L Code Check (Past) Code verification result / OK or NG OK: Verification confirmed
      NG (PAST): Verification not conformed      		 -
      S Code Check (Past) Code verification result / OK or NG OK: Verification confirmed
      NG (PAST): Verification not conformed      		 -
      #Code Diagnostic trouble code / Min.: 0, Max.: 255 - -
      COMBINATION METER:

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Vehicle Speed Meter Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Almost the same as the actual vehicle speed (Wheel driving) -
      Engine RPM Engine speed / Min.: 0 RPM, Max.: 12,750 RPM Almost the same as the actual engine speed (When engine is running) -
      Key Remind Volum Key remind warning volume / LARGE, MEDIUM, SMALL Customization status is displayed -
      Key Remind Sound Key remind warning sound / FAST, NORMAL, SLOW Customization status is displayed -
  2. ACTIVE TEST 

    HINT: 

    Perform the Active Test using Techstream to operate the motors of the front seat outer belts. Performing the Active Test is one of the methods to shorten labor time. It is possible to display the Data List during the Active Test.

    1. Connect Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Following the display on the tester, select the "Active Test".
      CERTIFICATION ECU:

      Tester Display Test Part Control Range Diagnostic Note
      Overhead Tuner Cabin Tuner ON / OFF -
      D Transmitter Door Oscillator (Front LH) ON / OFF -
      P Transmitter Door Oscillator (Front RH) ON / OFF -
      Fr Transmitter Cabin Oscillator (Front) ON / OFF -
      In-Bdr Transmitter Luggage Compartment Oscillator (Inner) ON / OFF -
      Bdoor Transmitter Luggage Compartment Oscillator (Outer) ON / OFF -
      D Select Sig D-sheet Select ON / OFF The same condition as when the key is brought near the vehicle will occur even if the key is not brought near the vehicle.
      P Select Sig P-sheet Select ON / OFF The same condition as when the key is brought near the vehicle will occur even if the key is not brought near the vehicle.
      Security Indic Security Indicator Light ON / OFF -
      COMBINATION METER:

      Tester Display Test Part Control Range Diagnostic Note
      Indicat Lamp Door Open Door Warning Light ON / OFF -
      Key Remind Buzzer Key Remained Buzzer ON / OFF -
      Warning Buzzer Warning Buzzer ON / OFF -
      Indicat SMART KEY Smart Key System Warning Light ON / OFF -
scientia non olet · About LEMON Manuals