Typical Enabling Conditions
WARNING: This page is about a different variant/trim than selected.
All
TYPICAL ENABLING CONDITIONS CHART
| The monitor will run whenever the following DTCs are not stored | P0115, P0117, P0118: ECT (Engine coolant temperature) sensor circuit P0120, P0122, P0123, P0220, P0222, P0223, P2102, P2103, P2118, P2135: ETCS (Electronic throttle control system) P0327, P0328, P032C, P032D, P0332, P0333, P033C, P033D: KCS sensor circuit P0502, P0503: Output speed sensor circuit P0712, P0713: ATF temperature sensor circuit P0715, P0717: Turbine speed sensor circuit P0748: Shift solenoid valve SL1 circuit P0778: Shift solenoid valve SL2 circuit P0798: Shift solenoid valve SL3 circuit P0985, P0986: Shift solenoid valve SR circuit P2810: Shift solenoid valve SL4 circuit P2819: Shift solenoid valve SL5 circuit U0100: CAN communication circuit (ECM - TCM) |
| NSW switch | "D" |
| Duration time from shifting "N" to "D" | 4 sec. or more |
| ATF temperature | -10°C (14°F) or higher |
| Engine | Running |
OFF malfunction (A)
TYPICAL ENABLING CONDITIONS CHART
| TCM indicated pressure value of SL1 | 1600 kPa (16.3 kgf/cm2 , 232 psi) |
OFF malfunction (B)
TYPICAL ENABLING CONDITIONS CHART
| TCM selected gear | 1st |
| Duration time from vehicle speed reaching the following value | Less than 3 sec. |
| Vehicle speed | 2 km/h (1.24 mph) or more and less than 40 km/h (24.86 mph) |
| Engine speed - Turbine speed | 150 RPM or more |
| Calculated load value | 7.75% or more |
| ECT (Engine Coolant Temperature) | 40°C (104°F) or higher |
| Spark advance from max. retard timing by KCS control | Crankshaft angle 0° or more |
When either condition below is met: Condition (1) or (2)
Condition (1)
When one of the following conditions is met: Condition (a), (b), (c), (d), (e), (f), (g) or (h)
Condition (a)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 1st gear) | More than 3.9 and 8.0 or less (when output speed less than 130 RPM) |
Condition (b)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 2nd gear) | More than 2.4 and 2.9 or less (when output speed less than 200 RPM) |
Condition (c)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 3rd gear) | More than 1.72 and 2.07 or less (when output speed less than 400 RPM) |
Condition (d)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 4th gear) | More than 1.354 and 1.584 or less (when output speed less than 600 RPM) |
Condition (e)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 5th gear) | More than 1.141 and 1.291 or less (when output speed less than 600 RPM) |
Condition (f)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 6th gear) | More than 0.93 and 1.07 or less (when output speed less than 800 RPM) |
Condition (g)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 7th gear) | More than 0.759 and 0.889 or less (when output speed less than 800 RPM) |
Condition (h)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 8th gear) | More than 0.62 and 0.75 or less (when output speed less than 1000 RPM) |
Condition (2)
When all conditions below are met: Condition (a), (b), (c), (d), (e), (f), (g) and (h)
Condition (a)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 1st gear ratio (Actual 1st gear) | More than -50 RPM and 50 RPM or less (when output speed 130 RPM or more) |
Condition (b)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 2nd gear ratio (Actual 2nd gear) | More than -50 RPM and 50 RPM or less (when output speed 200 RPM or more) |
Condition (c)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 3rd gear ratio (Actual 3rd gear) | More than -50 RPM and 50 RPM or less (when output speed 400 RPM or more) |
Condition (d)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 4th gear ratio (Actual 4th gear) | More than -50 RPM and 50 RPM or less (when output speed 600 RPM or more) |
Condition (e)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 5th gear ratio (Actual 5th gear) | More than -50 RPM and 50 RPM or less (when output speed 600 RPM or more) |
Condition (f)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 6th gear ratio (Actual 6th gear) | More than -50 RPM and 50 RPM or less (when output speed 800 RPM or more) |
Condition (g)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 7th gear ratio (Actual 7th gear) | More than -50 RPM and 50 RPM or less (when output speed 800 RPM or more) |
Condition (h)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 8th gear ratio (Actual 8th gear) | More than -50 RPM and 50 RPM or less (when output speed 1000 RPM or more) |
OFF malfunction (C)
TYPICAL ENABLING CONDITIONS CHART
| TCM selected gear | 2nd |
| Vehicle speed | 2 km/h (1.24 mph) or more |
| Throttle valve opening amount | 6.5% or more at engine speed 2000 RPM (condition varies with engine speed) |
| Calculated load value | 7.75% or more |
| ECT (Engine Coolant Temperature) | 40°C (104°F) or higher |
| Spark advance from max. retard timing by KCS control | Crankshaft angle 0° or more |
When either condition below is met: Condition (1) or (2)
Condition (1)
When one of the following conditions is met: Condition (a), (b), (c), (d), (e), (f), (g) or (h)
Condition (a)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 1st gear) | More than 3.9 and 8.0 or less (when output speed less than 130 RPM) |
Condition (b)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 2nd gear) | More than 2.4 and 2.9 or less (when output speed less than 200 RPM) |
Condition (c)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 3rd gear) | More than 1.72 and 2.07 or less (when output speed less than 400 RPM) |
Condition (d)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 4th gear) | More than 1.354 and 1.584 or less (when output speed less than 600 RPM) |
Condition (e)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 5th gear) | More than 1.141 and 1.291 or less (when output speed less than 600 RPM) |
Condition (f)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 6th gear) | More than 0.93 and 1.07 or less (when output speed less than 800 RPM) |
Condition (g)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 7th gear) | More than 0.759 and 0.889 or less (when output speed less than 800 RPM) |
Condition (h)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 8th gear) | More than 0.62 and 0.75 or less (when output speed less than 1000 RPM) |
Condition (2)
When all conditions below are met: Condition (a), (b), (c), (d), (e), (f), (g) and (h)
Condition (a)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 1st gear ratio (Actual 1st gear) | More than -50 RPM and 50 RPM or less (when output speed 130 RPM or more) |
Condition (b)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 2nd gear ratio (Actual 2nd gear) | More than -50 RPM and 50 RPM or less (when output speed 200 RPM or more) |
Condition (c)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 3rd gear ratio (Actual 3rd gear) | More than -50 RPM and 50 RPM or less (when output speed 400 RPM or more) |
Condition (d)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 4th gear ratio (Actual 4th gear) | More than -50 RPM and 50 RPM or less (when output speed 600 RPM or more) |
Condition (e)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 5th gear ratio (Actual 5th gear) | More than -50 RPM and 50 RPM or less (when output speed 600 RPM or more) |
Condition (f)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 6th gear ratio (Actual 6th gear) | More than -50 RPM and 50 RPM or less (when output speed 800 RPM or more) |
Condition (g)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 7th gear ratio (Actual 7th gear) | More than -50 RPM and 50 RPM or less (when output speed 800 RPM or more) |
Condition (h)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 8th gear ratio (Actual 8th gear) | More than -50 RPM and 50 RPM or less (when output speed 1000 RPM or more) |
OFF malfunction (D)
TYPICAL ENABLING CONDITIONS CHART
| TCM selected gear | 3rd |
| Vehicle speed | 2 km/h (1.24 mph) or more |
| Throttle valve opening amount | 6.5% or more at engine speed 2000 RPM (condition varies with engine speed) |
| Calculated load value | 7.75% or more |
| ECT (Engine Coolant Temperature) | 40°C (104°F) or higher |
| Spark advance from max. retard timing by KCS control | Crankshaft angle 0° or more |
When either condition below is met: Condition (1) or (2)
Condition (1)
When one of the following conditions is met: Condition (a), (b), (c), (d), (e), (f), (g) or (h)
Condition (a)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 1st gear) | More than 3.9 and 8.0 or less (when output speed less than 130 RPM) |
Condition (b)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 2nd gear) | More than 2.4 and 2.9 or less (when output speed less than 200 RPM) |
Condition (c)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 3rd gear) | More than 1.72 and 2.07 or less (when output speed less than 400 RPM) |
Condition (d)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 4th gear) | More than 1.354 and 1.584 or less (when output speed less than 600 RPM) |
Condition (e)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 5th gear) | More than 1.141 and 1.291 or less (when output speed less than 600 RPM) |
Condition (f)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 6th gear) | More than 0.93 and 1.07 or less (when output speed less than 800 RPM) |
Condition (g)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 7th gear) | More than 0.759 and 0.889 or less (when output speed less than 800 RPM) |
Condition (h)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 8th gear) | More than 0.62 and 0.75 or less (when output speed less than 1000 RPM) |
Condition (2)
When ail conditions below are met: Condition (a), (b), (c), (d), (e), (f), (g) and (h)
Condition (a)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 1st gear ratio (Actual 1st gear) | More than -50 RPM and 50 RPM or less (when output speed 130 RPM or more) |
Condition (b)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 2nd gear ratio (Actual 2nd gear) | More than -50 RPM and 50 RPM or less (when output speed 200 RPM or more) |
Condition (c)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 3rd gear ratio (Actual 3rd gear) | More than -50 RPM and 50 RPM or less (when output speed 400 RPM or more) |
Condition (d)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 4th gear ratio (Actual 4th gear) | More than -50 RPM and 50 RPM or less (when output speed 600 RPM or more) |
Condition (e)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 5th gear ratio (Actual 5th gear) | More than -50 RPM and 50 RPM or less (when output speed 600 RPM or more) |
Condition (f)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 6th gear ratio (Actual 6th gear) | More than -50 RPM and 50 RPM or less (when output speed 800 RPM or more) |
Condition (g)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 7th gear ratio (Actual 7th gear) | More than -50 RPM and 50 RPM or less (when output speed 800 RPM or more) |
Condition (h)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 8th gear ratio (Actual 8th gear) | More than -50 RPM and 50 RPM or less (when output speed 1000 RPM or more) |
OFF malfunction (E)
TYPICAL ENABLING CONDITIONS CHART
| TCM selected gear | 4th |
| Vehicle speed | 2 km/h (1.24 mph) or more |
| Throttle valve opening amount | 6.5% or more at engine speed 2000 RPM (condition varies with engine speed) |
| Calculated load value | 7.75% or more |
| ECT (Engine Coolant Temperature) | 40°C (104°F) or higher |
| Spark advance from max. retard timing by KCS control | Crankshaft angle 0° or more |
When either condition below is met: Condition (1) or (2)
Condition (1)
When one of the following conditions is met: Condition (a), (b), (c), (d), (e), (f), (g) or (h)
Condition (a)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 1st gear) | More than 3.9 and 8.0 or less (when output speed less than 130 RPM) |
Condition (b)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 2nd gear) | More than 2.4 and 2.9 or less (when output speed less than 200 RPM) |
Condition (c)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 3rd gear) | More than 1.72 and 2.07 or less (when output speed less than 400 RPM) |
Condition (d)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 4th gear) | More than 1.354 and 1.584 or less (when output speed less than 600 RPM) |
Condition (e)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 5th gear) | More than 1.141 and 1.291 or less (when output speed less than 600 RPM) |
Condition (f)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 6th gear) | More than 0.93 and 1.07 or less (when output speed less than 800 RPM) |
Condition (g)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 7th gear) | More than 0.759 and 0.889 or less (when output speed less than 800 RPM) |
Condition (h)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 8th gear) | More than 0.62 and 0.75 or less (when output speed less than 1000 RPM) |
Condition (2)
When all conditions below are met: Condition (a), (b), (c), (d), (e), (f), (g) and (h)
Condition (a)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 1st gear ratio (Actual 1st gear) | More than -50 RPM and 50 RPM or less (when output speed 130 RPM or more) |
Condition (b)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 2nd gear ratio (Actual 2nd gear) | More than -50 RPM and 50 RPM or less (when output speed 200 RPM or more) |
Condition (c)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 3rd gear ratio (Actual 3rd gear) | More than -50 RPM and 50 RPM or less (when output speed 400 RPM or more) |
Condition (d)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 4th gear ratio (Actual 4th gear) | More than -50 RPM and 50 RPM or less (when output speed 600 RPM or more) |
Condition (e)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 5th gear ratio (Actual 5th gear) | More than -50 RPM and 50 RPM or less (when output speed 600 RPM or more) |
Condition (f)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 6th gear ratio (Actual 6th gear) | More than -50 RPM and 50 RPM or less (when output speed 800 RPM or more) |
Condition (g)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 7th gear ratio (Actual 7th gear) | More than -50 RPM and 50 RPM or less (when output speed 800 RPM or more) |
Condition (h)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 8th gear ratio (Actual 8th gear) | More than -50 RPM and 50 RPM or less (when output speed 1000 RPM or more) |
OFF malfunction (F)
TYPICAL ENABLING CONDITIONS CHART
| TCM selected gear | 5th |
| Vehicle speed | 2 km/h (1.24 mph) or more |
| Throttle valve opening amount | 6.5% or more at engine speed 2000 RPM (condition varies with engine speed) |
| Calculated load value | 7.75% or more |
| ECT (Engine Coolant Temperature) | 40°C (104°F) or higher |
| Spark advance from max. retard timing by KCS control | Crankshaft angle 0° or more |
When either condition below is met: Condition (1) or (2)
Condition (1)
When one of the following conditions is met: Condition (a), (b), (c), (d), (e), (f), (g) or (h)
Condition (a)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 1st gear) | More than 3.9 and 8.0 or less (when output speed less than 130 RPM) |
Condition (b)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 2nd gear) | More than 2.4 and 2.9 or less (when output speed less than 200 RPM) |
Condition (c)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 3rd gear) | More than 1.72 and 2.07 or less (when output speed less than 400 RPM) |
Condition (d)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 4th gear) | More than 1.354 and 1.584 or less (when output speed less than 600 RPM) |
Condition (e)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 5th gear) | More than 1.141 and 1.291 or less (when output speed less than 600 RPM) |
Condition (f)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 6th gear) | More than 0.93 and 1.07 or less (when output speed less than 800 RPM) |
Condition (g)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 7th gear) | More than 0.759 and 0.889 or less (when output speed less than 800 RPM) |
Condition (h)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed/Output speed (NT/NO) (Actual 8th gear) | More than 0.62 and 0.75 or less (when output speed less than 1000 RPM) |
Condition (2)
When all conditions below are met: Condition (a), (b), (c), (d), (e), (f), (g) and (h)
Condition (a)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 1st gear ratio (Actual 1st gear) | More than -50 RPM and 50 RPM or less (when output speed 130 RPM or more) |
Condition (b)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 2nd gear ratio (Actual 2nd gear) | More than -50 RPM and 50 RPM or less (when output speed 200 RPM or more) |
Condition (c)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 3rd gear ratio (Actual 3rd gear) | More than -50 RPM and 50 RPM or less (when output speed 400 RPM or more) |
Condition (d)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 4th gear ratio (Actual 4th gear) | More than -50 RPM and 50 RPM or less (when output speed 600 RPM or more) |
Condition (e)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 5th gear ratio (Actual 5th gear) | More than -50 RPM and 50 RPM or less (when output speed 600 RPM or more) |
Condition (f)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 6th gear ratio (Actual 6th gear) | More than -50 RPM and 50 RPM or less (when output speed 800 RPM or more) |
Condition (g)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 7th gear ratio (Actual 7th gear) | More than -50 RPM and 50 RPM or less (when output speed 800 RPM or more) |
Condition (h)
TYPICAL ENABLING CONDITIONS CHART
| Turbine speed - Output speed (NT - NO) x 8th gear ratio (Actual 8th gear) | More than -50 RPM and 50 RPM or less (when output speed 1000 RPM or more) |