LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2009 >> LS 600hL >> Repair and Diagnosis >> External Pages >> Different car >> Section 25 (Cruise Control) >> Cruise Control System >> Data List / Active Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test

WARNING: This page is about a different car, the 2008 Lexus LS 600hL. However, it is still accessible from the selected car via links, so may be relevant.
  1. DATA LIST 

    HINT.

    Using the Intelligent tester or Techstream to read the DATA LIST allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed Reading the DATA LIST information early in troubleshooting is one way to save diagnostic time.

    NOTE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
    1. Connect the Intelligent tester or Techstream to the DLC3
    2. Turn the power switch ON (IG)
    3. Turn the tester on
    4. Using the Intelligent tester or Techstream, enter the following menus.
      1. Intelligent tester - Select DIAGNOSIS / OBD/ MOBD / CCS / DATA LIST
      2. Techstream - Select' Powertrain / Cruise Control / Data List
    5. According to the display on tester, read the "DATA LIST"
      1. Intelligent tester

        CCS

        DIAGNOSTIC NOTE NORMAL CONDITION CHART

        Tester Display Measurement Item/Range Normal Condition
        VEHICLE SPD Vehicle speed/min 0 km/h (0 mph)max 255 km/h (159 mph) Actual vehicle speed is display
        MEMORY SPD Vehicle speed/min 0 km/h (0 mph) max 255 km/h (159 mph) Actual vehicle speed stored in memory
        THROTTLE Throttle operating angle/mm 0 %, max 125 % Actual throttle operating angle
        CCS OPER STATUS Shift lever position signal/ON or OFF ON Shift lever position D or S (8th, 7th, 6th, 5th or 4th gear)
        OFF Shift lever position except D or S (8th, 7th, 6th, 5th or 4th gear)
        CRUISE CONTROL Cruise control/ON or OFF ON Cruise control is ON
        OFF Cruise control is OFF
        CCS INDICATOR M CRUISE main indicator (M-CPU)/ ON or OFF ON CRUISE main indicator light is ON
        OFF CRUISE main indicator light is OFF
        CCS READY M Cruise control system standby condition (M-CPU)/ON or OFF ON Cruise control switch is ON
        OFF Cruise control switch is OFF
        MAIN SW (MAIN) Cruise control switch (M-CPU)/ ON or OFF ON' Cruise control switch is ON
        OFF Cruise control switch is OFF
        VEHICLE SPD CHG Vehicle speed sudden change signal/ON or OFF ON Sudden vehicle speed change
        OFF No sudden vehicle speed change
        CANCEL SW CANCEL switch/ON or OFF ON CANCEL switch is ON
        OFF CANCEL switch is OFF
        SET/COAST SW -/SET switch/ON or OFF ON -/SET switch is ON
        OFF -/SET switch is OFF
        RES/ACC SW +/RES switch/ON or OFF ON +/RES switch is ON
        OFF +/RES switch is OFF
        STP LIGHT SW1 M Stop light switch signal (Main CPU)/ON or OFF ON Brake pedal depressed
        OFF Brake pedal released
      2. Techstream Cruise Control

        Cruise Control

        DIAGNOSTIC NOTE NORMAL CONDITION CHART

        Tester Display Measurement Item/Range Normal Condition
        CCS Vehicle Spd Vehicle speed/min 0 km/h (0 mph) max 255 km/h (159 mph) Actual vehicle speed is display
        CCS Mem Vehicle Spd Vehicle speed/min 0 km/h (0 mph) max 255 km/h (159 mph) Actual vehicle speed stored in memory
        Throttle Opening Angle Throttle operating angle/mm 0 %, max 125% Actual throttle operating angle
        Cruise Operation Status Shift lever position signal/ON or OFF ON Shift lever position D or S (8th, 7th, 6th, 5th or 4th gear)
        OFF Shift lever position except D or S (8th, 7th, 6th, 5th or 4th gear)
        Cruise Control Cruise control/ON or OFF ON Cruise control is ON
        OFF Cruise control is OFF
        CCS Indicator M-CPU CRUISE main indicator (M-CPU)/ ON or OFF ON CRUISE main indicator light is ON
        OFF CRUISE main indicator light is OFF
        CCS Ready M-CPU Cruise control system standby condition (M-CPU)/ON or OFF ON Cruise control switch is ON
        OFF Cruise control switch is OFF
        Main SW M-CPU Cruise control switch (M-CPU)/ ON or OFF ON Cruise control switch is ON
        OFF Cruise control switch is OFF
        Vehicle Spd Change Vehicle speed sudden change signal/ON or OFF ON Sudden vehicle speed change
        OFF No sudden vehicle speed change
        Cancel Switch CANCEL switch/ON or OFF ON CANCEL switch is ON
        OFF CANCEL switch is OFF
        SET/COAST Switch -/SET switch/ON or OFF ON -/SET switch is ON
        OFF -/SET switch Is OFF
        RES/ACC Switch +/RES switch/ON or OFF ON +/RES switch is ON
        OFF +/RES switch is OFF
        Stop Light SW M-CPU Stop light switch signal (Main CPU)/ON or OFF ON Brake pedal depressed
        OFF Brake pedal released
        # Codes Number of present trouble codes/ mm 0, max 255 Number of DTCs will be displayed
  2. ACTIVE TEST 

    HINT:

    Using the Intelligent tester or Techstream to perform ACTIVE TESTs allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing ACTIVE TESTs early in troubleshooting is one way to save diagnostic time. DATA LIST information can be displayed while performing ACTIVE TESTs.

    1. Connect the Intelligent tester or Techstream to the DLC3.
    2. Turn the power switch ON (IG).
    3. Turn the tester on.
    4. Using the Intelligent tester or Techstream, enter the following menus:
      1. Intelligent tester - Select: DIAGNOSIS / OBD/ MOBD / METER / ACTIVE TEST.
      2. Techstream - Select: Body Electrical / Combination Meter / Active Test.
    5. According to the display on the tester, perform the "ACTIVE TEST".
      1. Intelligent tester

        METER

        TESTER DISPLAY CHART

        Tester Display Test Part Control Range
        CRUISE INDIC CRUISE main indicator ON / OFF
      2. Techstream

      Combination Meter

      TESTER DISPLAY CHART

      Tester Display Test Part Control Range
      Indicat Lamp Cruise CRUISE main indicator ON / OFF
scientia non olet · About LEMON Manuals