LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2011 >> HS 250h >> Repair and Diagnosis >> Body & Frame >> Seats >> Front Power Seat Control System (W/Memory) (Diagnostics - Introduction) >> FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) >> Data List / Active Test >> Data List / Active Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test

  1. DATA LIST 

    HINT: 

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    1. Turn the power switch off.
    2. Connect the Techstream to the DLC3.
    3. Turn the power switch on (IG).
    4. Turn the Techstream on.
    5. Enter the following menus: Body Electrical / Mirror L / Data List.
    6. Read the Data List according to the display on the Techstream.
      MIRROR L

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Seat Memory Switch 1 M1 switch / ON or OFF ON: M1 switch on
      OFF: M1 switch off      		 -
      Seat Memory Switch 2 M2 switch / ON or OFF ON: M2 switch on
      OFF: M2 switch off      		 -
      Seat Memory Switch 3 M3 switch / ON or OFF ON: M3 switch on
      OFF: M3 switch off      		 -
      Seat Memory Set Switch SET switch / ON or OFF ON: SET switch on
      OFF: SET switch off      		 -
    7. Enter the following menus: Body Electrical / Driver Seat / Data List.
    8. Read the Data List according to the display on the Techstream.
      DRIVER SEAT

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Reclining Rear Reclining switch signal (Rearward) / ON or OFF ON: Reclining switch (Rearward) on
      OFF: Reclining switch (Rearward) off      		 -
      Reclining Front Reclining switch signal (Forward) / ON or OFF ON: Reclining switch (Forward) on
      OFF: Reclining switch (Forward) off      		 -
      Front Vertical Down Front vertical switch signal (Downward) / ON or OFF ON: Front vertical switch (Downward) on
      OFF: Front vertical switch (Downward) off      		 -
      Front Vertical Up Front vertical switch signal (Upward) / ON or OFF ON: Front vertical switch (Upward) on
      OFF: Front vertical switch (Upward) off      		 -
      Lifter Switch Down Lifter switch signal (Downward) / ON or OFF ON: Lifter switch (Downward) on
      OFF: Lifter switch (Downward) off      		 -
      Lifter Switch Up Lifter switch signal (Upward) / ON or OFF ON: Lifter switch (Upward) on
      OFF: Lifter switch (Upward) off      		 -
      Slide Rear Sliding switch signal (Rearward) / ON or OFF ON: Sliding switch (Rearward) on
      OFF: Sliding switch (Rearward) off      		 -
      Slide Front Sliding switch signal (Forward) / ON or OFF ON: Sliding switch (Forward) on
      OFF: Sliding switch (Forward) off      		 -
      Seat Memory No1 Seat position memorized with M1 switch / Mem or Not Mem Mem: Memorized
      Not Mem: Not memorized      		 -
      Seat Memory No2 Seat position memorized with M2 switch / Mem or Not Mem Mem: Memorized
      Not Mem: Not memorized      		 -
      Seat Memory No3 Seat position memorized with M3 switch / Mem or Not Mem Mem: Memorized
      Not Mem: Not memorized      		 -
      Ignition Switch Communication state of power switch signal / ON or OFF ON: Power switch on (IG) signal received
      OFF: Power switch off signal not received      		 -
      P Switch Park (P) state signal / ON or OFF ON: Park (P) selected
      OFF: Shift state other than park (P) selected      		 -
      Parking Brake SW Parking brake switch status / ON or OFF ON: Parking brake applied
      OFF: Parking brake released      		 -
      Vehicle Speed Vehicle speed data / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) Actual vehicle speed -
      Power Voltage Power supply for front power seat switch LH / min: 0 V, max: 19.89 V Within range from 11 V to 14 V -
      Slide Position Seat sliding position / min: 0000, max: 65535 0: Foremost sliding position
      65535: Rearmost sliding position      		 -
      Reclining Position Seat reclining position / min: 0000, max: 65535 0: Rearmost reclining position
      65535: Foremost reclining position      		 -
      Front Vertical Position Seat front vertical position / min: 0000, max: 65535 0: Uppermost front vertical position
      65535: Lowermost front vertical position      		 -
      Lifter Position Seat lifter position / min: 0000, max: 65535 0: Uppermost lifter position
      65535: Lowermost lifter position      		 -
      Slide Pos Mem No1 Seat sliding position memorized with M1 switch / min: 0000, max: 65535 0: Foremost sliding position
      65535: Rearmost sliding position      		 -
      Reclining Pos Mem No1 Seat reclining position memorized with M1 switch / min: 0000, max: 65535 0: Foremost reclining position
      65535: Rearmost reclining position      		 -
      Frnt Vrtcl Pos Mem No1 Front vertical position memorized with M1 switch / min: 0000, max: 65535 0: Uppermost front vertical position
      65535: Lowermost front vertical position      		 -
      Lifter Pos Mem No1 Lifter position memorized with M1 switch / min: 0000, max: 65535 0: Uppermost lifter position
      65535: Lowermost lifter position      		 -
      Slide Pos Mem No2 Seat sliding position memorized with M2 switch / min: 0000, max: 65535 0: Foremost sliding position
      65535: Rearmost sliding position      		 -
      Reclining Pos Mem No2 Seat reclining position memorized with M2 switch / min: 0000, max: 65535 0: Foremost reclining position
      65535: Rearmost reclining position      		 -
      Frnt Vrtcl Pos Mem No2 Front vertical position memorized with M2 switch / min: 0000, max: 65535 0: Uppermost front vertical position
      65535: Rearmost front vertical position      		 -
      Lifter Pos Mem No2 Lifter position memorized with M2 switch / min: 0000, max: 65535 0: Uppermost lifter position
      65535: Lowermost lifter position      		 -
      Slide Pos Mem No3 Seat sliding position memorized with M3 switch / min: 0000, max: 65535 0: Foremost sliding position
      65535: Rearmost sliding position      		 -
      Reclining Pos Mem No3 Seat reclining position memorized with M3 switch / min: 0000, max: 65535 0: Foremost reclining position
      65535: Rearmost most reclining position      		 -
      Frnt Vrtcl Pos Mem No3 Front vertical position memorized with M3 switch / min: 0000, max: 65535 0: Uppermost front vertical position
      65535: Lowermost front vertical position      		 -
      Lifter Pos Mem No3 Lifter position memorized with M3 switch / min: 0000, max: 65535 0: Uppermost lifter position
      65535: Lowermost lifter position      		 -
      Headrest Switch UP Headrest switch signal (UP) / ON or OFF ON: Headrest switch (UP) on
      OFF: Headrest switch (UP) off      		 Although it is displayed in the Techstream, the vehicle does not have this switch
      Headrest Switch Down Headrest switch signal (Down) / ON or OFF ON: Headrest switch (Down) on
      OFF: Headrest switch (Down) off      		 Although it is displayed in the Techstream, the vehicle does not have this switch
      Motor Status State of slide motor control/STANDBY, MOVING, LOCK STANDBY: Slide motor is idle
      MOVING: Slide motor is moving
      LOCK: Slide motor is locked      		 -
      Lifter Initialize Flag Seat lifter limit position memory / ON or OFF ON: Memorized
      OFF: Not memorized      		 -
      Front Vertical Init Flag Seat front vertical limit position memory / ON or OFF ON: Memorized
      OFF: Not memorized      		 -
      Reclining Position Init Flg Seat reclining limit position memory / ON or OFF ON: Memorized
      OFF: Not memorized      		 -
      Slide Position Init Flg Seat sliding limit position memory / ON or OFF ON: Memorized
      OFF: Not memorized      		 -
      Slide Position Front Limit Seat sliding position / min: 0000, max: 65535 0: Foremost sliding position
      65535: Rearmost sliding position      		 -
      Slide Position Rear Limit Seat sliding position / min: 0000, max: 65535 0: Foremost sliding position
      65535: Rearmost sliding position      		 -
      Reclining Position Front Limit Seat reclining position / min: 0000, max: 65535 0: Foremost reclining position
      65535: Rearmost reclining position      		 -
      Reclining Position Rear Limit Seat reclining position / min: 0000, max: 65535 0: Foremost reclining position
      65535: Rearmost reclining position      		 -
      Front Vertical UP Limit Seat front vertical position / min: 0000, max: 65535 0: Uppermost front vertical position
      65535: Lowermost front vertical position      		 -
      Front Vertical Down Limit Seat front vertical position / min: 0000, max: 65535 0: Uppermost front vertical position
      65535: Lowermost front vertical position      		 -
      Lifter Position UP Limit Seat lifter position / min: 0000, max: 65535 0: Uppermost lifter position
      65535: Lowermost lifter position      		 -
      Lifter Position Down Limit Seat lifter position / min: 0000, max: 65535 0: Uppermost lifter position
      65535: Lowermost lifter position      		 -
      Shift P SW (PMN) Park (P) state signal / ON or OFF ON: Park (P) selected
      OFF: Shift state other than park (P) selected      		 -
      Memory Button Buzzer Request Driver seat buzzer request display / OFF, MOVE, REGISTRY, CANCEL, REG NG, REG WAIT OFF: Buzzer does not sound
      MOVE: Request to sound buzzer when starting memory replay
      REGISTRY: Request to sound buzzer when starting memory registration
      CANCEL: Request to sound buzzer when canceling memory call registration
      REG NG: Request to sound buzzer when memory call registration not possible
      REG WAIT: Request to sound buzzer when starting memory call cabin scan      		 -
      Driver Seat Request Command Driver seat operation request received / OFF, MEMORY, MEM MOV, MEM SOD, RES MOV, AWY MOV, ASY SOD, MEM AWY or MEM RET OFF: No instruction
      MEMORY: Request to memorize
      MEM MOV: Request to recall memory
      MEM SOD: Request to replay
      RET MOV: Request to return
      AWAY MOV: Request to move away
      AWAY SOD: Request to recall away position memory
      MEM AWAY: Request to recall memorized position of seat back
      MEM RET: Request to restore seat back to memorized position      		 -
      Driver Seat POS REQ Seat memory switch operation value / OFF, MEM1, MEM2, MEM3, DRV1, DRV2 or DRV3 OFF: No operation
      MEM1: M1 switch operation status
      MEM2: M2 switch operation status
      MEM3: M3 switch operation status
      DRV1: Other 1 operation status
      DRV2: Other 2 operation status
      DRV3: Other 3 operation status      		 -
      Away Move Range Scale Driver seat slide away distance / NONE, SMALL, STANDARD or LONG NONE: No movement
      SMALL: Moves short distance
      STANDARD: Moves standard distance      		 -
      Return Move Return destination / AVAIL or NOT AVAIL AVAIL: Return destination set
      NOT AVAIL: Return destination not set      		 -
      Return & Away Function Power easy access system status / AVAIL or NOT AVAIL AVAIL: Power easy access system functioning
      NOT AVAIL: Power easy access system not functioning      		 -
      Driver Seat Buckle SW Status of the driver seatbelt / ON or OFF ON: Tongue plate engaged
      OFF: Tongue plate not engaged      		 -
      Slide Pos Mem Drv1 Seat sliding position memorized with seat memory switch DRV1 / min: 0000, max: 65535 0: Foremost sliding position
      65535: Rearmost sliding position      		 -
      Reclining Pos Mem Drv1 Seat reclining position memorized with seat memory switch DRV1 / min: 0000, max: 65535 0: Foremost reclining position
      65535: Rearmost reclining position      		 -
      Front Vertical Pos Mem Drv1 Seat front vertical position memorized with seat memory switch DRV1 / min: 0000, max: 65535 0: Uppermost front vertical position
      65535: Lowermost front vertical position      		 -
      Lifter Pos Mem Drv1 Seat lifter position memorized with seat memory switch DRV1 / min: 0000, max: 65535 0: Uppermost lifter position
      65535: Lowermost lifter position      		 -
      Slide Pos Mem Drv2 Seat sliding position memorized with seat memory switch DRV2 / min: 0000, max: 65535 0: Foremost sliding position
      65535: Rearmost sliding position      		 -
      Reclining Pos Mem Drv2 Seat reclining position memorized with seat memory switch DRV2 / min: 0000, max: 65535 0: Foremost reclining position
      65535: Rearmost reclining position      		 -
      Front Vertical Pos Mem Drv2 Seat front vertical position memorized with seat memory switch DRV2 / min: 0000, max: 65535 0: Uppermost front vertical position
      65535: Lowermost front vertical position      		 -
      Lifter Pos Mem Drv2 Seat lifter position memorized with seat memory switch DRV2 / min: 0000, max: 65535 0: Uppermost lifter position
      65535: Lowermost lifter position      		 -
      Return Position Return position / min: 0000, max: 65535 0: Foremost sliding position
      65535: Rearmost sliding position      		 -
      Sensor Power Voltage Sensor Power Voltage / min: 0 V, max: 19.89 V 11 to 14 V -
      Slide Pos Mem Drv3 Seat sliding position memorized with seat memory switch DRV3 / min: 0000, max: 65535 0: Foremost sliding position
      65535: Rearmost sliding position      		 -
      Reclining Pos Mem Drv3 Seat reclining position memorized with seat memory switch DRV3 / min: 0000, max: 65535 0: Foremost reclining position
      65535: Rearmost reclining position      		 -
      Front Vertical Pos Mem Drv3 Seat front vertical position memorized with seat memory switch DRV3 / min: 0000, max: 65535 0: Uppermost front vertical position
      65535: Lowermost front vertical position      		 -
      Lifter Pos Mem Drv3 Seat lifter position memorized with seat memory switch DRV3 / min: 0000, max: 65535 0: Uppermost lifter position
      65535: Lowermost lifter position      		 -
      Number of Trouble Codes Number of trouble codes/Min.: 0 or Max.: 255 Number of DTCs will be displayed -
    9. Enter the following menus: Body Electrical / Main Body / Data List.
    10. Read the Data List according to the display on the Techstream.
      MAIN BODY

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Seat Move Distance Power easy access system customization state / OFF, Little or Standard OFF: Power easy access system set to OFF
      Little: Power easy access system set to Little
      Standard: Power easy access system set to Standard      		 -
      Seat position/Tilt & Telesco memory recall setting Memory call customization state / D Door or ANY Door D Door: Memory call operate with driver door open
      ANY Door: Memory call operate with any door open      		 -
      Mem SW No. w/KeyID1 Memory switch linked with key ID1 / NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID1
      MEM SW1: M1 switch linked with key ID1
      MEM SW2: M2 switch linked with key ID1
      MEM SW3: M3 switch linked with key ID1      		 -
      Mem SW No. w/KeyID2 Memory switch linked with key ID2 / NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID2
      MEM SW1: M1 switch linked with key ID2
      MEM SW2: M2 switch linked with key ID2
      MEM SW3: M3 switch linked with key ID2      		 -
      Mem SW No. w/KeyID3 Memory switch linked with key ID3 / NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID3
      MEM SW1: M1 switch linked with key ID3
      MEM SW2: M2 switch linked with key ID3
      MEM SW3: M3 switch linked with key ID3      		 -
      Mem SW No. w/KeyID4 Memory switch linked with key ID4 / NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID4
      MEM SW1: M1 switch linked with key ID4
      MEM SW2: M2 switch linked with key ID4
      MEM SW3: M3 switch linked with key ID4      		 -
      Mem SW No. w/KeyID5 Memory switch linked with key ID5 / NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID5
      MEM SW1: M1 switch linked with key ID5
      MEM SW2: M2 switch linked with key ID5
      MEM SW3: M3 switch linked with key ID5      		 -
      Mem SW No. w/KeyID6 Memory switch linked with key ID6 / NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID6
      MEM SW1: M1 switch linked with key ID6
      MEM SW2: M2 switch linked with key ID6
      MEM SW3: M3 switch linked with key ID6      		 -
      Mem SW No. w/KeyID7 Memory switch linked with key ID7 / NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID7
      MEM SW1: M1 switch linked with key ID7
      MEM SW2: M2 switch linked with key ID7
      MEM SW3: M3 switch linked with key ID7      		 -
      Driver Seat Memory1 Seat position memorized with M1 switch/OFF or ON OFF: Not memorized
      ON: Memorized      		 -
      Driver Seat Memory2 Seat position memorized with M2 switch/OFF or ON OFF: Not memorized
      ON: Memorized      		 -
      Driver Seat Memory3 Seat position memorized with M3 switch/OFF or ON OFF: Not memorized
      ON: Memorized      		 -
      D Seat Configuration Driver seat configuration/NONE, Not RTN or Return NONE: Driver seat without memory system
      Not RTN: Driver seat with memory system (w/o power easy access system)
      Return: Driver seat with memory system (w/ power easy access system)      		 -
  2. ACTIVE TEST 

    HINT: 

    Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Turn the power switch off.
    2. Connect the Techstream to the DLC3.
    3. Turn the power switch on (IG).
    4. Turn the Techstream on.
    5. Enter the following menus: Body Electrical / Driver Seat / Active Test.
    6. Perform the Active Test according to the display on the Techstream.
      DRIVER SEAT

      Tester Display Test Part Control Range Diagnostic Note
      Seat Reclining Seat reclining operation Front / OFF / Rear -
      Front Vertical Operation Seat front vertical operation Up / OFF / Down -
      Lifter Operation Seat lifter operation Up / OFF / Down -
      Seat Slide Operation Seat sliding operation Front / OFF / Rear -
      Buzzer Buzzer operation ON / OFF -
      Headrest Operation Headrest operation Up / OFF / Down Although it is displayed in the Techstream, the vehicle does not have this function
scientia non olet · About LEMON Manuals