Data List / Active Test
- DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTE:In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
- Turn the engine switch off.
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Body Electrical / Mirror L / Data List.
- Read the Data List according to the display on the Techstream.MIRROR L
Tester Display Measurement Item/Range Normal Condition Diagnostic Note Seat Memory Switch 1 M1 switch / ON or OFF ON: M1 switch on
OFF: M1 switch off- Seat Memory Switch 2 M2 switch / ON or OFF ON: M2 switch on
OFF: M2 switch off- Seat Memory Switch 3 M3 switch / ON or OFF ON: M3 switch on
OFF: M3 switch off- Seat Memory Set Switch SET switch / ON or OFF ON: SET switch on
OFF: SET switch off- - Enter the following menus: Body Electrical / D-Seat / Data List.
- Read the Data List according to the display on the Techstream.DRIVER SEAT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note Reclining Rear Reclining switch signal (Rearward) / ON or OFF ON: Reclining switch (Rearward) on
OFF: Reclining switch (Rearward) off- Reclining Front Reclining switch signal (Forward) / ON or OFF ON: Reclining switch (Forward) on
OFF: Reclining switch (Forward) off- Front Vertical Down Front vertical switch signal (Downward) / ON or OFF ON: Front vertical switch (Downward) on
OFF: Front vertical switch (Downward) off- Front Vertical Up Front vertical switch signal (Upward) / ON or OFF ON: Front vertical switch (Upward) on
OFF: Front vertical switch (Upward) off- Lifter Switch Down Lifter switch signal (Downward) / ON or OFF ON: Lifter switch (Downward) on
OFF: Lifter switch (Downward) off- Lifter Switch Up Lifter switch signal (Upward) / ON or OFF ON: Lifter switch (Upward) on
OFF: Lifter switch (Upward) off- Slide Rear Sliding switch signal (Rearward) / ON or OFF ON: Sliding switch (Rearward) on
OFF: Sliding switch (Rearward) off- Slide Front Sliding switch signal (Forward) / ON or OFF ON: Sliding switch (Forward) on
OFF: Sliding switch (Forward) off- Seat Memory No1 Seat position memorized with M1 switch / Mem or Not Mem Mem: Memorized
Not Mem: Not memorized- Seat Memory No2 Seat position memorized with M2 switch / Mem or Not Mem Mem: Memorized
Not Mem: Not memorized- Seat Memory No3 Seat position memorized with M3 switch / Mem or Not Mem Mem: Memorized
Not Mem: Not memorized- Ignition Switch Communication state of engine switch signal / ON or OFF ON: Engine switch on (IG) signal received
OFF: Engine switch off signal not received- P Switch Shift lever position P signal / ON or OFF ON: Shift lever in P
OFF: Shift lever not in P- Parking Brake SW Parking brake switch status / ON or OFF ON: Parking brake applied
OFF: Parking brake released- Vehicle Speed Vehicle speed data / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) Actual vehicle speed - Power Voltage Power supply for position control ECU and switch assembly / min: 0 V, max: 19.89 V Within range from 11 V to 14 V - Slide Position Seat sliding position / min: 0000, max: 65535 0: Frontmost sliding position
65535: Rearmost sliding position- Reclining Position Seat reclining position / min: 0000, max: 65535 0: Uppermost reclining position
65535: Lowest reclining position- Front Vertical Position Seat front vertical position / min: 0000, max: 65535 0: Frontmost front vertical position
65535: Rearmost front vertical position- Lifter Position Seat lifter position / min: 0000, max: 65535 0: Uppermost lifter position
65535: Lowest lifter position- Slide Pos Mem No1 Seat sliding position memorized with M1 switch / min: 0000, max: 65535 0: Frontmost sliding position
65535: Rearmost sliding position- Reclining Pos Mem No1 Seat reclining position memorized with M1 switch / min: 0000, max: 65535 0: Uppermost reclining position
65535: Lowest reclining position- Frnt Vrtcl Pos Mem No1 Front vertical position memorized with M1 switch / min: 0000, max: 65535 0: Frontmost front vertical position
65535: Rearmost front vertical position- Lifter Pos Mem No1 Lifter position memorized with M1 switch / min: 0000, max: 65535 0: Uppermost lifter position
65535: Lowest lifter position- Slide Pos Mem No2 Seat sliding position memorized with M2 switch / min: 0000, max: 65535 0: Frontmost sliding position
65535: Rearmost sliding position- Reclining Pos Mem No2 Seat reclining position memorized with M2 switch / min: 0000, max: 65535 0: Uppermost reclining position
65535: Lowest reclining position- Frnt Vrtcl Pos Mem No2 Front vertical position memorized with M2 switch / min: 0000, max: 65535 0: Frontmost front vertical position
65535: Rearmost front vertical position- Lifter Pos Mem No2 Lifter position memorized with M2 switch / min: 0000, max: 65535 0: Uppermost lifter position
65535: Lowest lifter position- Slide Pos Mem No3 Seat sliding position memorized with M3 switch / min: 0000, max: 65535 0: Frontmost sliding position
65535: Rearmost sliding position- Reclining Pos Mem No3 Seat reclining position memorized with M3 switch / min: 0000, max: 65535 0: Uppermost reclining position
65535: Lowest reclining position- Frnt Vrtcl Pos Mem No3 Front vertical position memorized with M3 switch / min: 0000, max: 65535 0: Frontmost front vertical position
65535: Rearmost front vertical position- Lifter Pos Mem No3 Lifter position memorized with M3 switch / min: 0000, max: 65535 0: Uppermost lifter position
65535: Lowest lifter position- Headrest Switch UP Headrest switch signal (UP) / ON or OFF ON: Headrest switch (UP) on
OFF: Headrest switch (UP) off- Headrest Switch Down Headrest switch signal (Down) / ON or OFF ON: Headrest switch (Down) on
OFF: Headrest switch (Down) off- Lifter Initialize Flag Seat lifter limit position memory / ON or OFF ON: memorized
OFF: not memorized- Front Vertical Init Flag Seat front vertical limit position memory / ON or OFF ON: memorized
OFF: not memorized- Reclining Position Init Flg Seat reclining limit position memory / ON or OFF ON: memorized
OFF: not memorized- Slide Position Init Flg Seat sliding limit position memory / ON or OFF ON: memorized
OFF: not memorized- Slide Position Front Limit Seat sliding position / min: 0000, max: 65535 0: Frontmost sliding position
65535: Rearmost sliding position- Slide Position Rear Limit Seat sliding position / min: 0000, max: 65535 0: Frontmost sliding position
65535: Rearmost sliding position- Reclining Position Front Limit Seat reclining position / min: 0000, max: 65535 0: Uppermost reclining position
65535: Lowest reclining position- Reclining Position Rear Limit Seat reclining position / min: 0000, max: 65535 0: Uppermost reclining position
65535: Lowest reclining position- Front Vertical UP Limit Seat front vertical position / min: 0000, max: 65535 0: Frontmost front vertical position
65535: Rearmost front vertical position- Front Vertical Down Limit Seat front vertical position / min: 0000, max: 65535 0: Frontmost front vertical position
65535: Rearmost front vertical position- Lifter Position UP Limit Seat lifter position / min: 0000, max: 65535 0: Uppermost lifter position
65535: Lowest lifter position- Lifter Position Down Limit Seat lifter position / min: 0000, max: 65535 0: Uppermost lifter position
65535: Lowest lifter position- Shift P SW (PMN) Shift lever position P signal / ON or OFF ON: Shift lever in P
OFF: Shift lever not in P- Memory Button Buzzer Request Driver seat buzzer request display / OFF, MOVE, REGISTRY, CANCEL, REG NG, REG WAIT OFF: Buzzer does not sound
MOVE: Request to sound buzzer when starting memory replay
REGISTRY: Request to sound buzzer when starting memory registration
CANCEL: Request to sound buzzer when canceling memory call registration
REG NG: Request to sound buzzer when memory call registration not possible
REG WAIT: Request to sound buzzer when starting memory call cabin scan- Driver Seat Request Command Driver seat operation request received / OFF, MEMORY, MEM MOV, MEM SOD, RES MOV, AWY MOV, ASY SOD, MEM AWY or MEM RET OFF: No instruction
MEMORY: Request to memorize
MEM MOV: Request to recall memory
MEM SOD: Request to replay
RET MOV: Request to return
AWAY MOV: Request to move away
AWAY SOD: Request to recall away position memory
MEM AWAY: Request to recall memorized position of seat back
MEM RET: Request to restore seat back to memorized position- Driver Seat POS REQ Seat memory switch operation value / OFF, MEM1, MEM2, MEM3, DRV1, DRV2 or DRV3 OFF: No operation
MEM1: M1 switch operation status
MEM2: M2 switch operation status
MEM3: M3 switch operation status
DRV1: Other 1 operation status
DRV2: Other 2 operation status
DRV3: Other 3 operation status- Away Move Range Scale Driver seat slide away distance / NONE, SMALL, STANDARD or LONG NONE: No movement
SMALL: Moves short distance
STANDARD: Moves standard distance- Return Move Return destination / AVAIL or NOT AVAIL AVAIL: Return destination set
NOT AVAIL: Return destination not set- Return and Away Function Power easy access system status / ON or OFF ON: Power easy access system functioning
OFF: Power easy access system not functioning- Driver Seat Buckle SW Status of the driver seatbelt / ON or OFF ON: Tongue plate engaged
OFF: Tongue plate not engaged- Slide Pos Mem Drv1 Seat sliding position memorized with seat memory switch DRV1 / min: 0000, max: 65535 0: Frontmost sliding position
65535: Rearmost sliding position- Reclining Pos Mem Drv1 Seat reclining position memorized with seat memory switch DRV1 / min: 0000, max: 65535 0: Uppermost reclining position
65535: Lowest reclining position- Front Vertical Pos Mem Drv1 Seat front vertical position memorized with seat memory switch DRV1 / min: 0000, max: 65535 0: Frontmost front vertical position
65535: Rearmost front vertical position- Lifter Pos Mem Drv1 Seat lifter position memorized with seat memory switch DRV1 / min: 0000, max: 65535 0: Uppermost lifter position
65535: Lowest lifter position- Slide Pos Mem Drv2 Seat sliding position memorized with seat memory switch DRV2 / min: 0000, max: 65535 0: Frontmost sliding position
65535: Rearmost sliding position- Reclining Pos Mem Drv2 Seat reclining position memorized with seat memory switch DRV2 / min: 0000, max: 65535 0: Uppermost reclining position
65535: Lowest reclining position- Front Vertical Pos Mem Drv2 Seat front vertical position memorized with seat memory switch DRV2 / min: 0000, max: 65535 0: Frontmost front vertical position
65535: Rearmost front vertical position- Lifter Pos Mem Drv2 Seat lifter position memorized with seat memory switch DRV2 / min: 0000, max: 65535 0: Uppermost lifter position
65535: Lowest lifter position- Return Position Return position / min: 0000, max: 65535 0: Frontmost sliding position
65535: Rearmost sliding position- Sensor Power Voltage Sensor Power Voltage / min: 0 V, max: 19.89 V Within range from 11 V to 14 V - Slide Pos Mem Drv3 Seat sliding position memorized with seat memory switch DRV3 / min: 0000, max: 65535 0: Frontmost sliding position
65535: Rearmost sliding position- Reclining Pos Mem Drv3 Seat reclining position memorized with seat memory switch DRV3 / min: 0000, max: 65535 0: Uppermost reclining position
65535: Lowest reclining position- Front Vertical Pos Mem Drv3 Seat front vertical position memorized with seat memory switch DRV3 / min: 0000, max: 65535 0: Frontmost front vertical position
65535: Rearmost front vertical position- Lifter Pos Mem Drv3 Seat lifter position memorized with seat memory switch DRV3 / min: 0000, max: 65535 0: Uppermost lifter position
65535: Lowest lifter position- - Enter the following menus: Body Electrical / Main Body / Data List.
- Read the Data List according to the display on the Techstream.MAIN BODY
Tester Display Measurement Item/Range Normal Condition Diagnostic Note Mem SW No. w/KeyID1 Memory switch linked with key ID1 / NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID1
MEM SW1: M1 switch linked with key ID1
MEM SW2: M2 switch linked with key ID1
MEM SW3: M3 switch linked with key ID1- Mem SW No. w/KeyID2 Memory switch linked with key ID2 / NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID2
MEM SW1: M1 switch linked with key ID2
MEM SW2: M2 switch linked with key ID2
MEM SW3: M3 switch linked with key ID2- Mem SW No. w/KeyID3 Memory switch linked with key ID3 / NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID3
MEM SW1: M1 switch linked with key ID3
MEM SW2: M2 switch linked with key ID3
MEM SW3: M3 switch linked with key ID3- Mem SW No. w/KeyID4 Memory switch linked with key ID4 / NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID4
MEM SW1: M1 switch linked with key ID4
MEM SW2: M2 switch linked with key ID4
MEM SW3: M3 switch linked with key ID4- Mem SW No. w/KeyID5 Memory switch linked with key ID5 / NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID5
MEM SW1: M1 switch linked with key ID5
MEM SW2: M2 switch linked with key ID5
MEM SW3: M3 switch linked with key ID5- Mem SW No. w/KeyID6 Memory switch linked with key ID6 / NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID6
MEM SW1: M1 switch linked with key ID6
MEM SW2: M2 switch linked with key ID6
MEM SW3: M3 switch linked with key ID6- Mem SW No. w/KeyID7 Memory switch linked with key ID7 / NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID7
MEM SW1: M1 switch linked with key ID7
MEM SW2: M2 switch linked with key ID7
MEM SW3: M3 switch linked with key ID7-
- ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
- Turn the engine switch off.
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Body Electrical / Driver Seat / Active Test.
- Perform the Active Test according to the display on the Techstream.DRIVER SEAT
Tester Display Test Part Control Range Diagnostic Note Seat Slide Operation Seat sliding operation Front / OFF / Rear - Lifter Operation Seat lifter operation Up / OFF / Down - Front Vertical Operation Seat front vertical operation Up / OFF / Down - Seat Reclining Seat reclining operation Front / OFF / Rear - Headrest Operation Seat headrest operation Up / OFF / Down - Buzzer Buzzer operation ON / OFF -