DTC P2119: Throttle Actuator Control Throttle Body Range / Performance [09/2014 - 10/2015]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
5. Read the DTCs.

   Result

   Result	Proceed to
   P2119 is output	A
   P2119 and other DTCs are output	B

   HINT: 

   If any DTCs other than P2119 are output, troubleshoot those DTCs first.

Result: 

B 

GO TO DTC CHART 

(Refer to DIAGNOSTIC TROUBLE CODE CHART [09/2014 - 10/2015] )

Result: 

A 

See step  2

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Clear DTCs (Refer to DTC CHECK / CLEAR [09/2014 - 10/2015] ).
5. Turn the engine switch off and wait for at least 30 seconds.
6. Turn the engine switch on (IG).
7. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1 and Throttle Position Command.
8. Read the values displayed on the Techstream while fully depressing and releasing the accelerator pedal quickly.

   Result

   Result	Proceed to
   Throttle Position No. 1 does not change	A
   Throttle Position No. 1 changes even a little	B

   HINT: 

   When a DTC is output, the system changes to fail-safe mode. Therefore, only use the data up until the time the DTC is stored for confirmation.

Result: 

B 

See step  4

Result: 

A 

See step  3

1. Inspect the throttle body assembly (Refer to INSPECTION [09/2014 - 10/2015] ).

Result: 

NG 

See step  7

Result: 

OK 

See step  4

1. Check for contamination between the throttle valve and housing. If necessary, clean the throttle body. Also, check that the throttle valve moves smoothly.

   OK

   Throttle valve is not contaminated with foreign objects and moves smoothly.

Result: 

NG 

See step  7

Result: 

OK 

See step  5

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Clear DTCs (Refer to DTC CHECK / CLEAR [09/2014 - 10/2015] ).
5. Turn the engine switch off and wait for at least 30 seconds.
6. Turn the engine switch on (IG) and turn the Techstream on.
7. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1, Throttle Position No. 2 and Throttle Position Command.
8. Read the values displayed on the Techstream while wiggling the ECM wire harness.
9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
10. Check for DTCs.

    Result

    Result	Proceed to
    Value in Data List changes when wire harness is wiggled, or DTC is output	A
    Other than above	B

Result: 

B 

See step  8

Result: 

A 

See step  6

1. As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector (Refer to ELECTRONIC CIRCUIT INSPECTION PROCEDURE [09/2014 - ] ).

Result: 

NEXT 

END 

1. Replace the throttle body assembly (Refer to REMOVAL [09/2014 - 10/2015] ).

   HINT: 

   Perform "Inspection After Repair" after replacing the throttle body assembly (Refer to INITIALIZATION [09/2014 - 10/2015] ).

Result: 

NEXT 

See step  8

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Clear DTCs (Refer to DTC CHECK / CLEAR [09/2014 - 10/2015] ).
5. Turn the engine switch off and wait for at least 30 seconds.
6. Turn the engine switch on (IG).
7. Turn the Techstream on.
8. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
10. Read the DTCs.

    Result

    Result	Proceed to
    DTC is not output	A
    DTC P2119 is output	B

Result: 

A 

END 

Result: 

B 

REPLACE ECM 

(Refer to REMOVAL [09/2014 - 10/2015] )