LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2015 >> IS 250 Base, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 17 (Engine Control System (2GR-FSE) - Service Information) >> Camshaft Position Sensor >> Installation [04/2013 - 10/2017] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Installation [04/2013 - 10/2017]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2017 Lexus IS 350, 2017 Lexus IS 300, 2016 Lexus IS 350, 2016 Lexus IS 300, and 2015 Lexus IS 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL VVT SENSOR (for Exhaust Side of Bank 2) 
    1. Clean and degrease the threads of the bolt for the VVT sensor.
    2. Apply a light coat of engine oil to the O-ring of the VVT sensor.
    3. Install the VVT sensor to the cylinder head cover sub-assembly LH with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

      NOTE:
      • If a VVT sensor has been struck or dropped, replace it.
      • Make sure that the O-ring is not cracked or does not move out of place during installation.
    4. Connect the VVT sensor connector.
  2. INSTALL VVT SENSOR (for Intake Side of Bank 2) 
    1. Clean and degrease the threads of the bolt for the VVT sensor.
    2. Apply a light coat of engine oil to the O-ring of the VVT sensor.
    3. Install the VVT sensor to the cylinder head cover sub-assembly LH with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

      NOTE:
      • If a VVT sensor has been struck or dropped, replace it.
      • Make sure that the O-ring is not cracked or does not move out of place during installation.
    4. Connect the VVT sensor connector.
  3. INSTALL VVT SENSOR (for Exhaust Side of Bank 1) 
    1. Clean and degrease the threads of the bolt for the VVT sensor.
    2. Apply a light coat of engine oil to the O-ring of the VVT sensor.
    3. Install the VVT sensor to the cylinder head cover sub-assembly with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

      NOTE:
      • If a VVT sensor has been struck or dropped, replace it.
      • Make sure that the O-ring is not cracked or does not move out of place during installation.
    4. Connect the VVT sensor connector.
  4. INSTALL VVT SENSOR (for Intake Side of Bank 1) 
    1. Clean and degrease the threads of the bolt for the VVT sensor.
    2. Apply a light coat of engine oil to the O-ring of the VVT sensor.
    3. Install the VVT sensor to the cylinder head cover sub-assembly with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

      NOTE:
      • If a VVT sensor has been struck or dropped, replace it.
      • Make sure that the O-ring is not cracked or does not move out of place during installation.
    4. Connect the VVT sensor connector.
  5. INSTALL V-BANK COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 105 [04/2013 - 08/2015] , or refer to PROCEDURE - Step 106 [08/2015 - 10/2016] , or refer to PROCEDURE - Step 106 [10/2016 - 10/2017]

scientia non olet · About LEMON Manuals