LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2015 >> IS 250 Base, RWD >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Occupant Classification System - Diagnostics - Introduction >> Occupant Classification System >> Data List / Active Test [04/2013 - ] >> Data List / Active Test [04/2013 - ]
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test [04/2013 - ]

  1. DATA LIST 

    HINT: 

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    1. Turn the engine switch off.
    2. Connect the Techstream to the DLC3.
    3. Turn the engine switch on (IG).
    4. Turn the Techstream on.
    5. Enter the following menus: Body Electrical / Occupant Detection / Data List.
    6. Check the values by referring to the table below.

      Body Electrical > Occupant Detection > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      IG Switch Engine switch condition ON: Engine switch on (IG)
      OFF: Engine switch off      		 ON/OFF -
      Passenger Buckle SW Passenger side buckle switch Set: The seat belt is fastened
      Unset: The seat belt is not fastened
      NG: Data is not determined      		 Set/Unset -
      Passenger Classification Passenger classification AM50: Adult is seated
      AF05: Adult is seated
      Child: Child is seated
      CRS: Child restraint system is installed
      OFF: Vacant      		 AM50/AF05/Child/CRS/OFF -
      Sensor Range Info Sensor range information OK: Always OK As sensor range is not set, OK is always displayed
      FL Sensor Range Info Front left sensor range information OK: Always OK As front left sensor range is not set, OK is always displayed
      RL Sensor Range Info Rear left sensor range information OK: Always OK As rear left sensor range is not set, OK is always displayed
      FL Sensor Voltage Front left sensor voltage Min.: 0.000 V
      Max.: 19.800 V      		 0.000 to 5.000 V -
      RL Sensor Voltage Rear left sensor voltage Min.: 0.000 V
      Max.: 19.800 V      		 0.000 to 5.000 V -
      FL Sensor Weight Info Front left sensor weight information Min.: -10.00 kg (-22.05 lb)
      Max.: 20.00 kg (44.09 lb)      		 -10.00 to 20.00 kg
      (-22.05 to 44.09 lb)      		 -
      RL Sensor Weight Info Rear left sensor weight information Min.: -10.00 kg (-22.05 lb)
      Max.: 30.00 kg (66.13 lb)      		 -10.00 to 30.00 kg
      (-22.05 to 66.13 lb)      		 -
      Total Weight Information Total weight information Min.: -40.00 kg (-88.19 lb)
      Max.: 100.00 kg (220.46 lb)      		 -40.00 to 100.00 kg
      (-88.19 to 220.46 lb)      		 -
      Number of Present DTC Number of present DTC recorded Min.: 0, Max.: 255 0 -
      Number of Past DTC Number of past DTC recorded Min.: 0, Max.: 255 0 -
scientia non olet · About LEMON Manuals